Realtek ARM64 based SoC DT for v5.5
Add RTD1293 and RTD1296 DTs. Add the watchdog for all of RTD129x DTs.
Add reset controllers for RTD129x and start using them for UARTs.
* tag 'realtek-arm64-dt-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek:
arm64: dts: realtek: Add RTD129x UART resets
arm64: dts: realtek: Add RTD129x reset controller nodes
dt-bindings: reset: Add Realtek RTD1295
arm64: dts: realtek: Add watchdog node for RTD129x
arm64: dts: realtek: Add oscillator for RTD129x
arm64: dts: realtek: Add RTD1296 and Synology DS418
dt-bindings: arm: realtek: Document RTD1296 and Synology DS418
arm64: dts: realtek: Add RTD1293 and Synology DS418j
arm64: dts: realtek: Change dual-license from MIT to BSD
dt-bindings: arm: realtek: Document RTD1293 and Synology DS418j
dt-bindings: arm: realtek: Tidy up conversion to json-schema
Link: https://lore.kernel.org/r/20191030041000.31848-2-afaerber@suse.de
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCFPGA DTS updates for v5.5
- Arria10
- modify QSPI read-delay property
- Agilex
- Add QSPI support
- Enable USB and LEDs
- Add service layer, fpga manager support
- Stratix10
- Update QSPI reg address
* tag 'socfpga_dts_updates_for_v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: agilex: add service layer, fpga manager and fpga region
arm64: agilex: enable USB and LEDs on agilex devkit
arm64: dts: altera: update QSPI reg addresses for Stratix10
arm64: dts: agilex: add QSPI support for Intel Agilex
ARM: dts: arria10: Modify QSPI read_delay for Arria10
Link: https://lore.kernel.org/r/20191029143737.24850-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a header with symbolic reset indices for Realtek RTD1295 SoC.
Naming was derived from reset-names in an OEM's Device Tree.
Acked-by: Rob Herring <robh@kernel.org>
[AF: Dropped RTD1295 specific binding definition, updated SPDX]
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add the watchdog node to the RTD129x Device Tree.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
[AF: Moved from RTD1295 to new RTD129x]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move the SPDX-License-Identifier to the top line and update to SPDX 2.0.
While at it, switch from GPLv2+/MIT to GPLv2+/BSD2c before adding more.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
STM32 DT updates for v5.5, round 1
Highlights:
----------
MPU part:
-Add and enable ADC support on stm32mp157a-dk1
-Add DAC support on stm32mp157c-ed1
-Add and enable VREFBUF support on stm32mp157a-dk1
-Add focaltech touchscreen on stm32mp157c-dk2
-Add hdmi support on stm32mp157a-dk1
-Fix issues seen during YAML DT validation
-Fix regulators issues for all MPU boards
MCU part:
-Fix issues seen during YAML DT validation
* tag 'stm32-dt-for-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: remove useless dma-ranges property for stm32f469
ARM: dts: stm32: remove useless dma-ranges property for stm32f429
ARM: dts: stm32: disable active-discharge for vbus_otg on stm32mp157a-avenger96
ARM: dts: stm32: Fix active discharge usage on stm32mp157
ARM: dts: stm32: change default minimal buck1 value on stm32mp157
ARM: dts: stm32: add PWR regulators support on stm32mp157
ARM: dts: stm32: remove useless interrupt from dsi node for stm32f469
ARM: dts: stm32: add hdmi audio support to stm32mp157a-dk1 board
ARM: dts: stm32: Add DAC support to stm32mp157c-ed1
ARM: dts: stm32: Add DAC pins used on stm32mp157c-ed1
ARM: dts: stm32: fix regulator-sd_switch node on stm32mp157c-ed1 board
ARM: dts: stm32: remove usb phy-names entries on stm32mp157c-ev1
ARM: dts: stm32: fix joystick node on stm32f746 and stm32mp157c eval boards
ARM: dts: stm32: fix memory nodes to match with DT validation tool
ARM: dts: stm32: add focaltech touchscreen on stm32mp157c-dk2 board
ARM: dts: stm32: enable ADC support on stm32mp157a-dk1
ARM: dts: stm32: add ADC pins used on stm32mp157a-dk1
ARM: dts: stm32: Enable VREFBUF on stm32mp157a-dk1
ARM: dts: stm32: move ltdc pinctrl on stm32mp157a dk1 board
Link: https://lore.kernel.org/r/02c39510-f36d-abbb-c76f-49aff07c0a08@st.com
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv8 Juno update for v5.5
Single patch to add support for Mali GPU on all versions of Juno.
Though it's disabled by default, it is very useful to test panfrost
drivers.
* tag 'juno-update-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: add GPU subsystem
Link: https://lore.kernel.org/r/20191028040022.GC20568@e107533-lin.cambridge.arm.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Restore the device names for compatible strings as comments.
Prepare for adding more SoCs by inserting oneOf.
Fixes: 693af5f3ee ("dt-bindings: arm: Convert Realtek board/soc bindings to json-schema")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Active discharge is not needed on vbus_otg and generate unneeded current
consumption.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Minimal value is the value set during boot or before suspend.
We must ensure that the value is a functional value to boot.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of STM32 PWR regulators on
stm32mp157c. This replace dummy fixed regulators on
stm32mp157c-ed1 and stm32mp157c-dk2.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DSI driver doesn't use interrupt, remove it from the node since it
breaks yaml check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c-ed1 board has digital-to-analog converter signals routed
to JP11 and JP10 jumpers (e.g. PA4/PA5).
It's easier then to configure them both. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used by digital-to-analog converter on
stm32mp157c eval daughter board:
- PA4 and PA5 pins are available respectively on JP11 and JP10
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"phy-names" entries are not used. To be compliant with DT validation
tool, those entries have to be remove.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"#size-cells" entry is not needed for "gpio-keys" driver. Indeed "reg"
entry is not used. This commit will fix a warnings seen by DT validation
tool.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DT validation ("make dtbs_check") has shown that some memory nodes were not
correctly written. This commit fixes this kind of issue:
"stm32f746-disco.dt.yaml: /: memory: False schema does not allow
{'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}"
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure ADC support on stm32mp157a-dk1. It can be used for various
purpose:
- AIN connector has several analog inputs: ANA0, ANA1, ADC2 in6 & in2,
ADC1 in13 & in6
- USB Type-C CC1 & CC2 pins wired to in18 & in19
It's easier then to Configure them all. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Add VDD and VDDA supplies to ADC on stm32mp157c-dk1 board. This allows to
get full ADC analog performances in case VDDA is below 2.7V (not the case
by default).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used for ADC on stm32mp157a-dk1 board:
- AIN connector has ADC input pins
- USB Type-C CC1 & CC2 pins (e.g. in18, in19)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The ltdc pinctrl must be in the display controller node and
not in the peripheral node (hdmi bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
Device tree changes for omaps for v5.5
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
* tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: add DTS for NetCom Plus 4xx and 8xx device series
ARM: dts: add DTS for NetCom Plus 1xx and 2xx device series
ARM: dts: add DTS for NetCAN Plus devices
ARM: dts: omap: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo-37xx-devkit: Increase camera pixel clock
ARM: dts: am: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo: Disable Bluetooth Serial DMA
ARM: dts: IGEP: Add WiLink UART node
ARM: dts: LogicPD Torpedo: Add WiLink UART node
ARM: dts: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel
ARM: dts: logicpd-torpedo-baseboard: Reduce video regulator chatter
ARM: dts: Add minimal support for Droid Bionic xt875
ARM: dts: omap4-droid4: Allow 300mA current for USB peripherals
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
* tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: add label to sp805 watchdog
ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
arm64: dts: broadcom: Add reference to RPi 4 B
ARM: dts: Add minimal Raspberry Pi 4 support
dt-bindings: arm: bcm2835: Add Raspberry Pi 4 to DT schema
dt-bindings: arm: Convert BCM2835 board/soc bindings to json-schema
ARM: dts: bcm283x: Move BCM2835/6/7 specific to bcm2835-common.dtsi
ARM: dts: bcm283x: Remove brcm,bcm2835-pl011 compatible
ARM: dts: bcm283x: Remove simple-bus from fixed clocks
Link: https://lore.kernel.org/r/20191023212814.30622-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This DTS file covers all four and eight port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers all one and two port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers both NetCAN Plus 110 and 120 WLAN models.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe musb with ti-sysc interconnect driver and dts data
with the following changes:
1. Swap the old ti,am33xx-usb compatible wrapper to generic ti-sysc
driver. This means later on we can also remove the old wrapper driver
drivers/usb/musb/musb_am335x.c
2. Update the child nodes to use the ranges provided by ti-sysc
3. Drop unneeded status = "enabled" tinkering for SoC internal devices.
This allows us to remove some useless board specific boilerplate code
in the following patches
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
