- Remove unused static pcie_base and pcie_dev (Geert Uytterhoeven)
* pci/controller/rcar:
PCI: rcar: Use correct product family name for Renesas R-Car
PCI: rcar-host: Remove unused static pcie_base and pcie_dev
- Disable register write access after init for IP v2.3.3, v2.9.0
(Manivannan Sadhasivam)
- Use DWC helpers for enabling/disabling writes to DBI registers
(Manivannan Sadhasivam)
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0 (Manivannan Sadhasivam)
- Reuse v2.3.2 post-init sequence for v2.4.0 (Manivannan Sadhasivam)
-
* pci/controller/qcom:
PCI: qcom: Do not advertise hotplug capability for IP v2.1.0
PCI: qcom: Do not advertise hotplug capability for IP v1.0.0
PCI: qcom: Use post init sequence of IP v2.3.2 for v2.4.0
PCI: qcom: Do not advertise hotplug capability for IP v2.3.2
PCI: qcom: Do not advertise hotplug capability for IPs v2.3.3 and v2.9.0
PCI: qcom: Do not advertise hotplug capability for IPs v2.7.0 and v1.9.0
PCI: qcom: Disable write access to read only registers for IP v2.9.0
PCI: qcom: Use DWC helpers for modifying the read-only DBI registers
PCI: qcom: Disable write access to read only registers for IP v2.3.3
- Wait for link to come up only if we've initiated link training (Ajay
Agarwal)
- Save and restore imx6 Root Port MSI control to work around hardware
defect (Richard Zhu)
* pci/controller/dwc:
PCI: imx6: Save and restore root port MSI control in suspend and resume
PCI: dwc: Wait for link up only if link is started
- Wait for link retrain to complete when working around the J721E i2085
erratum with Gen2 mode (Siddharth Vadapalli)
* pci/controller/cadence:
PCI: cadence: Fix Gen2 Link Retraining process
- Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM hang
when guest is rebooted (Mike Pastore)
- Add function 1 DMA alias quirk for Marvell 88SE9235 (Robin Murphy)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SE9235
PCI: Delay after FLR of Solidigm P44 Pro NVMe
- When we coalesce host bridge windows, remove invalidated resources from
the resource tree so future allocations work correctly (Ross Lagerwall)
* pci/resource:
PCI: Release resource invalidated by coalescing
- Reduce wait time for secondary bus to be ready to speed up resume (Mika
Westerberg)
- Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in D3cold
(Ondrej Zary)
- Call _REG when transitioning D-states so AML that uses the PCI config
space OpRegion works, which fixes some ASMedia GPIO controllers (Mario
Limonciello)
* pci/pm:
PCI/ACPI: Call _REG when transitioning D-states
PCI/ACPI: Validate acpi_pci_set_power_state() parameter
PCI/PM: Avoid putting EloPOS E2/S2/H2 PCIe Ports in D3cold
PCI/PM: Shorten pci_bridge_wait_for_secondary_bus() wait time for slow links
- Simplify Attention Button logging (Bjorn Helgaas)
- Cancel bringup sequence if card is not present, to keep from blinking
Power Indicator indefinitely (Rongguang Wei)
- Reassign bridge resources if necessary for ACPI hotplug (Igor Mammedov)
* pci/hotplug:
PCI: acpiphp: Reassign resources on bridge if necessary
PCI: pciehp: Cancel bringup sequence if card is not present
PCI: pciehp: Simplify Attention Button logging
- Add PCI_EXT_CAP_ID_PL_32GT define (Ben Dooks)
- Propagate firmware node by calling device_set_node() for better
modularity (Andy Shevchenko)
- Discover Data Link Layer Link Active Reporting earlier so quirks can take
advantage of it (Maciej W. Rozycki)
- Use cached Data Link Layer Link Active Reporting capability in pciehp,
powerpc/eeh, and mlx5 (Maciej W. Rozycki)
- Run quirk for devices that require OS to clear Retrain Link earlier, so
later quirks can rely on it (Maciej W. Rozycki)
- Export pcie_retrain_link() for use outside ASPM (Maciej W. Rozycki)
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up (Maciej W. Rozycki)
- Work around link training failures (especially on the ASMedia ASM2824
switch) by training first at 2.5GT/s and then attempting higher rates
(Maciej W. Rozycki)
* pci/enumeration:
PCI: Add failed link recovery for device reset events
PCI: Work around PCIe link training failures
PCI: Use pcie_wait_for_link_status() in pcie_wait_for_link_delay()
PCI: Add support for polling DLLLA to pcie_retrain_link()
PCI: Export pcie_retrain_link() for use outside ASPM
PCI: Export PCIe link retrain timeout
PCI: Execute quirk_enable_clear_retrain_link() earlier
PCI/ASPM: Factor out waiting for link training to complete
PCI/ASPM: Avoid unnecessary pcie_link_state use
PCI/ASPM: Use distinct local vars in pcie_retrain_link()
net/mlx5: Rely on dev->link_active_reporting
powerpc/eeh: Rely on dev->link_active_reporting
PCI: pciehp: Rely on dev->link_active_reporting
PCI: Initialize dev->link_active_reporting earlier
PCI: of: Propagate firmware node by calling device_set_node()
PCI: Add PCI_EXT_CAP_ID_PL_32GT define
# Conflicts:
# drivers/pci/pcie/aspm.c
- Disable ASPM on MFD function removal to avoid use-after-free (Ding Hui)
- Tighten up pci_enable_link_state() and pci_disable_link_state()
interfaces so they don't enable/disable states the driver didn't specify
(Ajay Agarwal)
- Avoid link retraining race that can happen if ASPM sets link control
parameters while the link is in the midst of training for some other
reason (Ilpo Järvinen)
* pci/aspm:
PCI/ASPM: Avoid link retraining race
PCI/ASPM: Factor out pcie_wait_for_retrain()
PCI/ASPM: Return 0 or -ETIMEDOUT from pcie_retrain_link()
PCI/ASPM: Remove unnecessary ASPM_STATE_L1SS check
PCI/ASPM: Rename L1.2-specific functions from 'l1ss' to 'l12'
PCI/ASPM: Set ASPM_STATE_L1 when driver enables L1.1 or L1.2
PCI/ASPM: Set only ASPM_STATE_L1 when driver enables L1
PCI/ASPM: Disable only ASPM_STATE_L1 when driver disables L1
PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free
- Unexport pci_save_aer_state() since it's only used in drivers/pci/ (Bjorn
Helgaas)
- Drop recommendation for drivers to configure AER Capability, since the
PCI core does this for all devices (Dave Jiang, Bjorn Helgaas)
* pci/aer:
Documentation: PCI: Tidy AER documentation
Documentation: PCI: Update cross references to .rst files
Documentation: PCI: Drop recommendation to configure AER Capability
PCI: Unexport pci_save_aer_state()
ACPI r6.5, sec 6.5.4, describes how AML is unable to access an
OperationRegion unless _REG has been called to connect a handler:
The OS runs _REG control methods to inform AML code of a change in the
availability of an operation region. When an operation region handler is
unavailable, AML cannot access data fields in that region. (Operation
region writes will be ignored and reads will return indeterminate data.)
The PCI core does not call _REG at any time, leading to the undefined
behavior mentioned in the spec.
The spec explains that _REG should be executed to indicate whether a
given region can be accessed:
Once _REG has been executed for a particular operation region, indicating
that the operation region handler is ready, a control method can access
fields in the operation region. Conversely, control methods must not
access fields in operation regions when _REG method execution has not
indicated that the operation region handler is ready.
An example included in the spec demonstrates calling _REG when devices are
turned off: "when the host controller or bridge controller is turned off
or disabled, PCI Config Space Operation Regions for child devices are
no longer available. As such, ETH0’s _REG method will be run when it
is turned off and will again be run when PCI1 is turned off."
It is reported that ASMedia PCIe GPIO controllers fail functional tests
after the system has returning from suspend (S3 or s2idle). This is because
the BIOS checks whether the OSPM has called the _REG method to determine
whether it can interact with the OperationRegion assigned to the device as
part of the other AML called for the device.
To fix this issue, call acpi_evaluate_reg() when devices are transitioning
to D3cold or D0.
[bhelgaas: split pci_power_t checking to preliminary patch]
Link: https://uefi.org/specs/ACPI/6.5/06_Device_Configuration.html#reg-region
Link: https://lore.kernel.org/r/20230620140451.21007-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Previously acpi_pci_set_power_state() assumed the requested power state was
valid (PCI_D0 ... PCI_D3cold). If a caller supplied something else, we
could index outside the state_conv[] array and pass junk to
acpi_device_set_power().
Validate the pci_power_t parameter and return -EINVAL if it's invalid.
Link: https://lore.kernel.org/r/20230621222857.GA122930@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
PCIe r6.0.1, sec 7.5.3.7, recommends setting the link control parameters,
then waiting for the Link Training bit to be clear before setting the
Retrain Link bit.
This avoids a race where the LTSSM may not use the updated parameters if it
is already in the midst of link training because of other normal link
activity.
Wait for the Link Training bit to be clear before toggling the Retrain Link
bit to ensure that the LTSSM uses the updated link control parameters.
[bhelgaas: commit log, return 0 (success)/-ETIMEDOUT instead of bool for
both pcie_wait_for_retrain() and the existing pcie_retrain_link()]
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/20230502083923.34562-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Attempt to handle cases such as with a downstream port of the ASMedia
ASM2824 PCIe switch where link training never completes and the link
continues switching between speeds indefinitely with the data link layer
never reaching the active state.
It has been observed with a downstream port of the ASMedia ASM2824 Gen 3
switch wired to the upstream port of the Pericom PI7C9X2G304 Gen 2 switch,
using a Delock Riser Card PCI Express x1 > 2 x PCIe x1 device, P/N 41433,
wired to a SiFive HiFive Unmatched board. In this setup the switches
should negotiate a link speed of 5.0GT/s, falling back to 2.5GT/s if
necessary.
Instead the link continues oscillating between the two speeds, at the rate
of 34-35 times per second, with link training reported repeatedly active
~84% of the time. Limiting the target link speed to 2.5GT/s with the
upstream ASM2824 device makes the two switches communicate correctly.
Removing the speed restriction afterwards makes the two devices switch to
5.0GT/s then.
Make use of these observations and detect the inability to train the link
by checking for the Data Link Layer Link Active status bit being off while
the Link Bandwidth Management Status indicating that hardware has changed
the link speed or width in an attempt to correct unreliable link operation.
Restrict the speed to 2.5GT/s then with the Target Link Speed field,
request a retrain and wait 200ms for the data link to go up. If this is
successful, lift the restriction, letting the devices negotiate a higher
speed.
Also check for a 2.5GT/s speed restriction the firmware may have already
arranged and lift it too with ports of devices known to continue working
afterwards (currently only ASM2824), that already report their data link
being up.
[bhelgaas: reorder and squash stubs from
https://lore.kernel.org/r/alpine.DEB.2.21.2306111619570.64925@angie.orcam.me.uk
to avoid adding stubs that do nothing]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203022037020.56670@angie.orcam.me.uk/
Link: https://source.denx.de/u-boot/u-boot/-/commit/a398a51ccc68
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2305310038540.59226@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove a DLLLA status bit polling loop from pcie_wait_for_link_delay() and
call almost identical code in pcie_wait_for_link_status() instead. This
reduces the lower bound on the polling interval from 10ms to 1ms, possibly
increasing the CPU load on the system in favour to reducing the wait time.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306111611170.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Let the caller of pcie_retrain_link() specify whether they want to use the
LT bit or the DLLLA bit of the Link Status Register to determine if link
training has completed. It is up to the caller to verify whether the use
of the DLLLA bit, the implementation of which is optional, is valid for the
device requested.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110310540.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export pcie_retrain_link() for link retrain needs outside ASPM. Struct
pcie_link_state is local to ASPM and only used by pcie_retrain_link() to
get at the associated PCI device, so change the operand and adjust the lone
call site accordingly. Document the interface. No functional change at
this point.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110229010.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
SoCs making use of Qcom PCIe controller IP v2.1.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IPs v2.3.3 and v2.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot
and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's not set the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-6-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot and
suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The imx6 PCI host controller suffers from a HW integration bug whereby
the MSI enable bit in the root port MSI capability enables/disables MSIs
interrupts for all downstream components in the PCI tree.
This requires, as implemented in
75cb8d20c1 ("PCI: imx: Enable MSI from downstream components")
that the root port MSI enable bit should be set in order for downstream
PCI devices MSIs to function.
The MSI enable bit programming might be lost during the suspend and
should be re-stored during resume.
Save the MSI control during suspend and restore it in resume.
Link: https://lore.kernel.org/r/1670479534-22154-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[lpieralisi@kernel.org: commit log]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Use separate local variables to hold the respective values retrieved from
the Link Control Register and the Link Status Register. Improves
readability and it makes it possible for the compiler to detect actual
uninitialised use should this code change in the future.
[bhelgaas: reorder to clean up before exposing to PCI core]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110252260.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is native"),
the PCI core enables PCIe device error reporting for all devices during
enumeration, so drivers don't need to do it.
Remove the recommendation for drivers to configure AER and call
pci_enable_pcie_error_reporting() themselves.
Also remove the suggestion that drivers may change AER mask and severity
registers. Ownership of these registers is negotiated between the OS and
platform firmware. If firmware owns these registers, the OS must not
change them.
Link: https://lore.kernel.org/r/20230609222500.1267795-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
