When the remain on channel is removed at the time it should
have expired, we have a race: the driver could be handling
the flow of the expiration while mac80211 is cancelling
that very same remain on channel request.
This wouldn't be problem in itself, but since mac80211
can send the next request to the driver in the cancellation
flow, we can get to the following situation:
CPU0 CPU1
expiration of roc in driver
ieee80211_remain_on_channel_expired()
Cancellation of the roc
schedules a worker (hw_roc_done)
Add next roc
hw_roc_done_wk runs and ends
the second roc prematurely.
Since, by design, there is only one single request sent to the
driver at a time, we can safely assume that after the cancel()
request returns from the driver, we should not handle any worker
that handles the expiration of the request.
Cancel the hw_roc_done worker after the cancellation to make
sure we start the next one with a clean slate.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.4e4469be20ac.Iab0525f5cc4698acf23eab98b8b1eec02099cde0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the scan parameters for a 6GHz scan specify a unicast
BSSID address, and the corresponding AP is found in the scan
list, add a corresponding entry in the collocated AP list,
so this AP would be directly probed even if it was not
advertised as a collocated AP.
This is needed for handling a scan request that is intended
for a ML probe flow, where user space can requests a scan
to retrieve information for other links in the AP MLD.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.54b954bc02ad.I1c072793d3d77a4c8fbbc64b4db5cce1bbb00382@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we have a per-link debugfs directory which contains the
per-link files. In case of non-MLO we would like to put the per-link
files in the netdev directory to keep it how it was before MLO.
- Upon interface creation the netdev will be created with the per-link
files in it.
- Upon switching to MLO: delete the entire netdev directory and then
recreate it without the per-link files. Then the per-link directories
with the per-link files in it will be created in ieee80211_link_init()
- Upon switching to non-MLO: delete the entire netdev directory
(including the per-link directories) and recreate it with the per-link
files in it.
Note that this also aligns to always call the vif link debugfs
method for the deflink as promised in the documentation, which
wasn't done before.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.082e698caca9.I5bef7b2026e0f58b4a958b3d1f459ac5baeccfc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a callback which the driver can use to add the vif debugfs.
We used to have this back until commit d260ff12e7 ("mac80211:
remove vif debugfs driver callbacks") where we thought that it
will be easier to just add them during interface add/remove.
However, now with multi-link, we want to have proper debugfs
for drivers for multi-link where some files might be in the
netdev for non-MLO connections, and in the links for MLO ones,
so we need to do some reconstruction when switching the mode.
Moving to this new call enables that and MLO drivers will have
to use it for proper debugfs operation.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.ac38913f6ab7.Iee731d746bb08fcc628fa776f337016a12dc62ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a race when the device is unbound (maybe because the
module is unloaded) while the opmode start hasn't finished yet.
The complete(request_firmware_complete) after the opmode start
was meant (and commented accordingly) to prevent this problem,
but it's not sufficient when the opmode module is loaded after
the firmware load already completed, which happens regularly
now because firmware load doesn't require userspace, unlike
module load.
Fix this by using the existing opmode registration mutex to
protected the start/stop flows against each other properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926110319.85951554fed8.I62f20f40d79d0f136fa05e46d7fc16dc437fa3db@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enabling KASAN and running some iperf tests raises some memory issues with
vmm_table:
BUG: KASAN: slab-out-of-bounds in wilc_wlan_handle_txq+0x6ac/0xdb4
Write of size 4 at addr c3a61540 by task wlan0-tx/95
KASAN detects that we are writing data beyond range allocated to vmm_table.
There is indeed a mismatch between the size passed to allocator in
wilc_wlan_init, and the range of possible indexes used later: allocation
size is missing a multiplication by sizeof(u32)
Fixes: 40b717bfce ("wifi: wilc1000: fix DMA on stack objects")
Cc: stable@vger.kernel.org
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231017-wilc1000_tx_oops-v3-1-b2155f1f7bee@bootlin.com
DCFO tracking compensate the CFO (carrier frequency offset) by digital
hardware that provides fine CFO estimation. Although the avg_cfo which
is a coarse information becomes zero, still we need DCFO tracking to
compensate the residual CFO. However, the original flow skips the case
when avg_cfo is zero, so we fix it to have expected performance.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-5-pkshih@realtek.com
Change naming to disambiguate the functions because their names are common
and not clear about the purpose. Not change logic at all.
These functions are to control baseband AGC while BT coexists with WiFi.
Among these functions, ctrl_btg_bt_rx is used to control AGC related
settings, which is affected by BT RX, while BT shares the same path
with wifi; ctrl_nbtg_bt_tx is used to control AGC settings under
non-shared path condition, which is affected by BT TX.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-2-pkshih@realtek.com
Sometimes firmware may enter strange state or infinite
loop due to unknown bug, and then it will lead critical
function fail, such as sending H2C command or changing
power mode. In these abnormal states, we add more debug
information, including hardware register status, to help
further investigation.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016053554.744180-3-pkshih@realtek.com
This is a kconfig warning in a randconfig when CONFIG_PCI is not set:
WARNING: unmet direct dependencies detected for SSB_EMBEDDED
Depends on [n]: SSB [=y] && SSB_DRIVER_MIPS [=y] && SSB_PCICORE_HOSTMODE [=n]
Selected by [y]:
- BCM47XX_SSB [=y] && BCM47XX [=y]
This is caused by arch/mips/bcm47xx/Kconfig's symbol BCM47XX_SSB
selecting SSB_EMBEDDED when CONFIG_PCI is not set.
This warning can be prevented by altering SSB_EMBEDDED to allow for
PCI=n or the former SSB_PCICORE_HOSTMODE.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Michael Büsch <m@bues.ch>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012220856.23260-1-rdunlap@infradead.org
Saeed Mahameed says:
====================
mlx5-updates-2023-10-10
1) Adham Faris, Increase max supported channels number to 256
2) Leon Romanovsky, Allow IPsec soft/hard limits in bytes
3) Shay Drory, Replace global mlx5_intf_lock with
HCA devcom component lock
4) Wei Zhang, Optimize SF creation flow
During SF creation, HCA state gets changed from INVALID to
IN_USE step by step. Accordingly, FW sends vhca event to
driver to inform about this state change asynchronously.
Each vhca event is critical because all related SW/FW
operations are triggered by it.
Currently there is only a single mlx5 general event handler
which not only handles vhca event but many other events.
This incurs huge bottleneck because all events are forced
to be handled in serial manner.
Moreover, all SFs share same table_lock which inevitably
impacts each other when they are created in parallel.
This series will solve this issue by:
1. A dedicated vhca event handler is introduced to eliminate
the mutual impact with other mlx5 events.
2. Max FW threads work queues are employed in the vhca event
handler to fully utilize FW capability.
3. Redesign SF active work logic to completely remove
table_lock.
With above optimization, SF creation time is reduced by 25%,
i.e. from 80s to 60s when creating 100 SFs.
Patches summary:
Patch 1 - implement dedicated vhca event handler with max FW
cmd threads of work queues.
Patch 2 - remove table_lock by redesigning SF active work
logic.
* tag 'mlx5-updates-2023-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Allow IPsec soft/hard limits in bytes
net/mlx5e: Increase max supported channels number to 256
net/mlx5e: Preparations for supporting larger number of channels
net/mlx5e: Refactor mlx5e_rss_init() and mlx5e_rss_free() API's
net/mlx5e: Refactor mlx5e_rss_set_rxfh() and mlx5e_rss_get_rxfh()
net/mlx5e: Refactor rx_res_init() and rx_res_free() APIs
net/mlx5e: Use PTR_ERR_OR_ZERO() to simplify code
net/mlx5: Use PTR_ERR_OR_ZERO() to simplify code
net/mlx5: fix config name in Kconfig parameter documentation
net/mlx5: Remove unused declaration
net/mlx5: Replace global mlx5_intf_lock with HCA devcom component lock
net/mlx5: Refactor LAG peer device lookout bus logic to mlx5 devcom
net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
net/mlx5: Redesign SF active work to remove table_lock
net/mlx5: Parallelize vhca event handling
====================
Link: https://lore.kernel.org/r/20231014171908.290428-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect both hi.data.modename and hi.data.drivername to be
NUL-terminated based on its usage with sprintf:
| sprintf(hi.data.modename, "%sclk,%smodem,fclk=%d,bps=%d%s",
| bc->cfg.intclk ? "int" : "ext",
| bc->cfg.extmodem ? "ext" : "int", bc->cfg.fclk, bc->cfg.bps,
| bc->cfg.loopback ? ",loopback" : "");
Note that this data is copied out to userspace with:
| if (copy_to_user(data, &hi, sizeof(hi)))
... however, the data was also copied FROM the user here:
| if (copy_from_user(&hi, data, sizeof(hi)))
Considering the above, a suitable replacement is strscpy_pad() as it
guarantees NUL-termination on the destination buffer while also
NUL-padding (which is good+wanted behavior when copying data to
userspace).
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231016-strncpy-drivers-net-hamradio-baycom_epp-c-v2-1-39f72a72de30@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I recently cleaned up specs to not specify enum-as-flags
when target enum is already defined as flags.
YNL Python library did not convert flags, unfortunately,
so this caused breakage for Stan and Willem.
Note that the nlspec.py abstraction already hides the differences
between flags and enums (value vs user_value), so the changes
are pretty trivial.
Fixes: 0629f22ec1 ("ynl: netdev: drop unnecessary enum-as-flags")
Reported-and-tested-by: Willem de Bruijn <willemb@google.com>
Reported-and-tested-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/all/ZS10NtQgd_BJZ3RU@google.com/
Link: https://lore.kernel.org/r/20231016213937.1820386-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: remove last of the phylink validate methods and clean up
This four patch series removes the last of the phylink MAC .validate
methods which can be found in the Freescale fman driver. fman has a
requirement that half duplex may not be supported in RGMII mode,
which is currently handled in its .validate method.
In order to keep this functionality when removing the .validate method,
we need to replace that with equivalent functionality, for which I
propose the optional .mac_get_caps method in the first patch.
The advantage of this approach over the .validate callback is that MAC
drivers only have to deal with the MAC_* capabilities, and don't need
to call back into phylink functions to do the masking of the ethtool
linkmodes etc - which then becomes internal to phylink. This can be
seen in the fourth patch where we make a load of these methods static.
====================
Link: https://lore.kernel.org/r/ZS1Z5DDfHyjMryYu@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a new method, mac_get_caps() to get the MAC capabilities for
the specified interface mode. This is for MACs which have special
requirements, such as not supporting half-duplex in certain interface
modes, and will replace the validate() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qsPk5-009wiX-G5@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent FW interface update bumped the size of struct hwrm_func_cfg_input
above 128B which is the max some devices support.
Probe on Stratus (BCM957452) with FW 20.8.3.11 fails with:
bnxt_en ...: Unable to reserve tx rings
bnxt_en ...: 2nd rings reservation failed.
bnxt_en ...: Not enough rings available.
Once probe is fixed other errors pop up:
bnxt_en ...: Failed to set async event completion ring.
This is because __hwrm_send() rejects requests larger than
bp->hwrm_max_ext_req_len with -E2BIG. Since the driver doesn't
actually access any of the new fields, yet, trim the length.
It should be safe.
Similar workaround exists for backing_store_cfg_input.
Although that one mins() to a constant of 256, not 128
we'll effectively use here. Michael explains: "the backing
store cfg command is supported by relatively newer firmware
that will accept 256 bytes at least."
To make debugging easier in the future add a warning
for oversized requests.
Fixes: 754fbf604f ("bnxt_en: Update firmware interface to 1.10.2.171")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231016171640.1481493-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added accounting and a limit for the number of
dynamically learned FDB entries per bridge. However it did not provide
means to actually configure those bounds or read back the count. This
patch does that.
Two new netlink attributes are added for the accounting and limit of
dynamically learned FDB entries:
- IFLA_BR_FDB_N_LEARNED (RO) for the number of entries accounted for
a single bridge.
- IFLA_BR_FDB_MAX_LEARNED (RW) for the configured limit of entries for
the bridge.
The new attributes are used like this:
# ip link add name br up type bridge fdb_max_learned 256
# ip link add name v1 up master br type veth peer v2
# ip link set up dev v2
# mausezahn -a rand -c 1024 v2
0.01 seconds (90877 packets per second
# bridge fdb | grep -v permanent | wc -l
256
# ip -d link show dev br
13: br: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 [...]
[...] fdb_n_learned 256 fdb_max_learned 256
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-3-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A malicious actor behind one bridge port may spam the kernel with packets
with a random source MAC address, each of which will create an FDB entry,
each of which is a dynamic allocation in the kernel.
There are roughly 2^48 different MAC addresses, further limited by the
rhashtable they are stored in to 2^31. Each entry is of the type struct
net_bridge_fdb_entry, which is currently 128 bytes big. This means the
maximum amount of memory allocated for FDB entries is 2^31 * 128B =
256GiB, which is too much for most computers.
Mitigate this by maintaining a per bridge count of those automatically
generated entries in fdb_n_learned, and a limit in fdb_max_learned. If
the limit is hit new entries are not learned anymore.
For backwards compatibility the default setting of 0 disables the limit.
User-added entries by netlink or from bridge or bridge port addresses
are never blocked and do not count towards that limit.
Introduce a new fdb entry flag BR_FDB_DYNAMIC_LEARNED to keep track of
whether an FDB entry is included in the count. The flag is enabled for
dynamically learned entries, and disabled for all other entries. This
should be equivalent to BR_FDB_ADDED_BY_USER and BR_FDB_LOCAL being unset,
but contrary to the two flags it can be toggled atomically.
Atomicity is required here, as there are multiple callers that modify the
flags, but are not under a common lock (br_fdb_update is the exception
for br->hash_lock, br_fdb_external_learn_add for RTNL).
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-2-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
