Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the commit e86dc1ca46 ("Libertas: cfg80211 support") we've lost
the ability to actually set the Mesh SSID from userspace.
NL80211_CMD_SET_INTERFACE with NL80211_ATTR_MESH_ID sets the mesh point
interface's ssid field. Let's use that one for the Libertas Mesh
operation
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate the array pwr_info_offset on the stack but instead make it
static const. Makes the object code smaller by 207 bytes.
Before:
text data bss dec hex filename
26066 3000 64 29130 71ca drivers/ssb/pci.o
After:
text data bss dec hex filename
25763 3096 64 28923 70fb drivers/ssb/pci.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arrays pwr_info_offset and sprom_sizes can be make static const rather
than populating them on the stack. Shrinks object size by 236 bytes.
Before:
text data bss dec hex filename
11300 1320 64 12684 318c drivers/bcma/sprom.o
After:
text data bss dec hex filename
10904 1480 64 12448 30a0 drivers/bcma/sprom.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
George McCollister says:
====================
add ksz9567 with I2C support to ksz9477 driver
Resurrect KSZ9477 I2C driver support patch originally sent to the list
by Tristram Ha and resolve outstanding issues. It now works as similarly to
the ksz9477 SPI driver as possible, using the same regmap macros.
Add support for ksz9567 to the ksz9477 driver (tested on a board with
ksz9567 connected via I2C).
Remove NET_DSA_TAG_KSZ_COMMON since it's not needed.
Changes since v1:
Put ksz9477_i2c.c includes in alphabetical order.
Added Reviewed-Bys.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the superfluous NET_DSA_TAG_KSZ_COMMON and just use the existing
NET_DSA_TAG_KSZ. Update the description to mention the three switch
families it supports. No functional change.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9567 7-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9567 supports both SPI and I2C. Oddly the
ksz9567 is already in the device tree binding documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
[george.mccollister@gmail.com: bring up to date, use ksz_common regmap macros]
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PluDevice register provides the authoritative chip model/revision.
Since the model number is purely used for reporting purposes, follow
the hardware team convention of subtracting 0x10 from the PluDevice
register to obtain the chip model/revision number.
Suggested-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp sends a TSO packet, adding a PSH flag on it
reduces the sojourn time of GRO packet in GRO receivers.
This is particularly the case under pressure, since RX queues
receive packets for many concurrent flows.
A sender can give a hint to GRO engines when it is
appropriate to flush a super-packet, especially when pacing
is in the picture, since next packet is probably delayed by
one ms.
Having less packets in GRO engine reduces chance
of LRU eviction or inflated RTT, and reduces GRO cost.
We found recently that we must not set the PSH flag on
individual full-size MSS segments [1] :
Under pressure (CWR state), we better let the packet sit
for a small delay (depending on NAPI logic) so that the
ACK packet is delayed, and thus next packet we send is
also delayed a bit. Eventually the bottleneck queue can
be drained. DCTCP flows with CWND=1 have demonstrated
the issue.
This patch allows to slowdown the aggregate traffic without
involving high resolution timers on senders and/or
receivers.
It has been used at Google for about four years,
and has been discussed at various networking conferences.
[1] segments smaller than MSS already have PSH flag set
by tcp_sendmsg() / tcp_mark_push(), unless MSG_MORE
has been requested by the user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the equivalent of commit 2c6b55f45d ("ipv6: fix neighbour
resolution with raw socket") for ip6_confirm_neigh(): we can send a
packet with MSG_CONFIRM on a raw socket for a connected route, so the
gateway would be :: here, and we should pick the next hop using
rt6_nexthop() instead.
This was found by code review and, to the best of my knowledge, doesn't
actually fix a practical issue: the destination address from the packet
is not considered while confirming a neighbour, as ip6_confirm_neigh()
calls choose_neigh_daddr() without passing the packet, so there are no
similar issues as the one fixed by said commit.
A possible source of issues with the existing implementation might come
from the fact that, if we have a cached dst, we won't consider it,
while rt6_nexthop() takes care of that. I might just not be creative
enough to find a practical problem here: the only way to affect this
with cached routes is to have one coming from an ICMPv6 redirect, but
if the next hop is a directly connected host, there should be no
topology for which a redirect applies here, and tests with redirected
routes show no differences for MSG_CONFIRM (and MSG_PROBE) packets on
raw sockets destined to a directly connected host.
However, directly using the dst gateway here is not consistent anymore
with neighbour resolution, and, in general, as we want the next hop,
using rt6_nexthop() looks like the only sane way to fetch it.
Reported-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for Synopsys HAPS board that uses GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Signed-off-by: Vitaly Gaiduk <vitaly.gaiduk@cloudbear.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation of ti,sgmii-ref-clock-output-enable
which can be used to select SGMII mode type (4 or 6-wire).
Signed-off-by: Vitaly Gaiduk <vitaly.gaiduk@cloudbear.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change documents the 'mac-mode' property that was introduced in the
'stmmac' driver to support passive mode converters that can sit in-between
the MAC & PHY.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-between the MAC & PHY there can be a mode converter, which converts one
mode to another (e.g. GMII-to-RGMII).
The converter, can be passive (i.e. no driver or OS/SW information
required), so the MAC & PHY need to be configured differently.
For the `stmmac` driver, this is implemented via a `mac-mode` property in
the device-tree, which configures the MAC into a certain mode, and for the
PHY a `phy_interface` field will hold the mode of the PHY. The mode of the
PHY will be passed to the PHY and from there-on it work in a different
mode. If unspecified, the default `phy-mode` will be used for both.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed* Fix series.
The patch series addresses couple of issues in the recent commits.
Patch (1) populates the actual dump-size of config attribute instead of
providing a fixed size value.
Patch(2) updates frame format of flash config buffer as required by
management FW (MFW).
Please consider applying it to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW associates the entity id to a config attribute instead of assigning
one entity id for all the config attributes.
This patch incorporates driver changes to link entity id to a config id
attribute.
Fixes: 0dabbe1bb3 ("qed: Add driver API for flashing the config attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently returns max-buf-size as size of the config attribute.
This patch incorporates changes to read this value from MFW (if available)
and provide it to the user. Also did a trivial clean up in this path.
Fixes: d44a3ced70 ("qede: Add support for reading the config id attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
devlink: add unknown 'fw_load_policy' value
Dirk says:
Recently we added an unknown value for the 'reset_dev_on_drv_probe' devlink
parameter. Extend the 'fw_load_policy' parameter in the same way.
The only driver that uses this right now is the nfp driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the 'reset_dev_on_drv_probe' devlink parameter, it is useful
to have an unknown value which can be used by drivers to report that the
hardware value isn't recognized or is otherwise invalid instead of
failing the operation.
This is especially useful for u8/enum parameters.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
