Remove the switch statement and base perst release on whether it is
found in the device tree. The probe function fails without the reset
property, making it mandatory. Therefore, always release reset
independent of the variant.
This does not change the behavior of the driver but reduces driver
complexity and allows for easier future modifications.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250305144355.20364-2-eichest@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
two functional blocks (XBar assist and VBus assist) and one system
access interface using APB.
The primary functionality of XBar assist is:
- switching lane for flip
- moving unused lanes into lower power states.
This info can be get from:
i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
This will add support for TCA block to achieve lane switching and tca
lower power functionality.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20241204050907.1081781-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY is based on a Samsung IP block that supports HDMI 2.1, and eDP
1.4b. RK3588 integrates the Analogix eDP 1.3 TX controller IP and the
HDMI/eDP TX Combo PHY to support eDP display.
Add basic support for RBR/HBR/HBR2 link rates, and the voltage swing and
pre-emphasis configurations of each link rate are set according to the
eDP 1.3 requirements.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-5-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables the clocks for the
whole lifetime of the device. Moreover, it is no longer necessary to
unprepare and disable the clocks explicitly.
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://lore.kernel.org/r/tencent_9087BCE04E38E6AA5C4B2252B82FA99C2009@qq.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20250111185407.183855-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To make USB runtime suspend work when a UDC has been bound, the phy
needs to inform the USBDRD controller (DWC3) that Vbus and bvalid are
gone, so that it can in turn raise the respective gadget interrupt with
event == DWC3_DEVICE_EVENT_DISCONNECT, which will cause the USB stack
to clean up, allowing DWC3 to enter runtime suspend.
On e850 and gs101 this isn't working, as the respective signals are not
directly connected, and instead this driver uses override bits in the
PHY IP to set those signals. It currently forcefully sets them to 'on',
so the above mentioned interrupt will not be raised, preventing runtime
suspend.
To detect that state, update this driver to act on the TCPC's
orientation signal - when orientation == NONE, Vbus is gone and we can
clear the respective bits. Similarly, for other orientation values we
re-enable them.
This makes runtime suspend work on platforms with a TCPC (like Pixel6),
while keeping compatibility with platforms without (e850-96).
With runtime suspend working, USB-C cable orientation detection now
also fully works on such platforms, and the link comes up as Superspeed
as expected irrespective of the cable orientation and whether UDC /
gadget are configured and active.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-7-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gs101's SS phy needs to be configured differently based on the
connector orientation, as the SS link can only be established if the
mux is configured correctly.
The code to handle programming of the mux is in place already, this commit
now adds the missing pieces to subscribe to the Type-C orientation
switch event.
Note that for this all to work we rely on the USB controller
re-initialising us. It should invoke our .exit() upon cable unplug, and
during cable plug we'll receive the orientation event after which we
expect our .init() to be called.
Above reinitialisation happens if the DWC3 controller can enter runtime
suspend automatically. For the DWC3 driver, this is an opt-in:
echo auto > /sys/devices/.../11110000.usb/power/control
Once done, things work as long as the UDC is not bound as otherwise it
stays busy because it doesn't cancel / stop outstanding TRBs. For now
we have to manually unbind the UDC in that case:
echo "" > sys/kernel/config/usb_gadget/.../UDC
Note that if the orientation-switch property is missing from the DT,
the code will behave as before this commit (meaning for gs101 it will
work in SS mode in one orientation only). Other platforms are not
affected either way.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-6-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USB SS lanes need to be configured based on the connector orientation -
at most two lanes will be in use for USB (and the remaining two for
alternate modes like DP).
For the USB link to come up in SS, the lane configuration registers
have to be programmed accordingly.
While we still need a way to be notified of the actual connector
orientation and then reprogram the registers accordingly (at the moment
the configuration happens just once during phy_init() and never again),
we can prepare the code doing the configuration to take the orientation
into account.
Do so.
Note: the mutex is needed to synchronize this with the upcoming
connector orientation callback.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-5-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
orientation-switch is the standard declaration to inform the Type-C mux
layer that a remote-endpoint is capable of processing orientation
change messages.
The USB PHY on gs101 needs to be configured based on the orientation of
the connector. For that the DTS needs a link between the phy's port and
a TCPCi, and we'll need to inform the phy driver that it should handle
the orientation (register a handler).
Update the schema to enforce that by requiring the orientation-switch
and port properties on gs101 (only). We disallow orientation-switch on
all other supported platforms, since other versions of this phy (or its
system integration) don't currently support or even need it.
Even though this new required gs101 property is an ABI break, the
intention for the driver is to behave as before if it's missing
(meaning for gs101 it will work in SS mode in one orientation only).
Other platforms are not affected.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-2-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Pull MIPS fix from Thomas Bogendoerfer:
"Revert commit breaking sysv ipc for o32 ABI"
* tag 'mips_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "mips: fix shmctl/semctl/msgctl syscall for o32"
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
gather_bootmem_prealloc() assumes the start nid as 0 and size as
num_node_state(N_MEMORY). That means in case if memory attached numa
nodes are interleaved, then gather_bootmem_prealloc_parallel() will fail
to scan few of these nodes.
Since memory attached numa nodes can be interleaved in any fashion, hence
ensure that the current code checks for all numa node ids
(.size = nr_node_ids). Let's still keep max_threads as N_MEMORY, so that
it can distributes all nr_node_ids among the these many no. threads.
e.g. qemu cmdline
========================
numa_cmd="-numa node,nodeid=1,memdev=mem1,cpus=2-3 -numa node,nodeid=0,cpus=0-1 -numa dist,src=0,dst=1,val=20"
mem_cmd="-object memory-backend-ram,id=mem1,size=16G"
w/o this patch for cmdline (default_hugepagesz=1GB hugepagesz=1GB hugepages=2):
==========================
~ # cat /proc/meminfo |grep -i huge
AnonHugePages: 0 kB
ShmemHugePages: 0 kB
FileHugePages: 0 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 1048576 kB
Hugetlb: 0 kB
with this patch for cmdline (default_hugepagesz=1GB hugepagesz=1GB hugepages=2):
===========================
~ # cat /proc/meminfo |grep -i huge
AnonHugePages: 0 kB
ShmemHugePages: 0 kB
FileHugePages: 0 kB
HugePages_Total: 2
HugePages_Free: 2
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 1048576 kB
Hugetlb: 2097152 kB
Link: https://lkml.kernel.org/r/f8d8dad3a5471d284f54185f65d575a6aaab692b.1736592534.git.ritesh.list@gmail.com
Fixes: b78b27d029 ("hugetlb: parallelize 1G hugetlb initialization")
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reported-by: Pavithra Prakash <pavrampu@linux.ibm.com>
Suggested-by: Muchun Song <muchun.song@linux.dev>
Tested-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Reviewed-by: Luiz Capitulino <luizcap@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Donet Tom <donettom@linux.ibm.com>
Cc: Gang Li <gang.li@linux.dev>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
