During remapping CCS FBs the CCS AUX surface mapped size and offset->x,y
coordinate calculations assumed a tiled layout. This works as long as
the CCS surface height is aligned to 64 lines (ensuring a 4k bytes CCS
surface tile layout). However this alignment is not required by the HW
(and the driver doesn't enforces it either).
Add the remapping logic required to remap the pages of CCS surfaces
without the above alignment, assuming the natural linear layout of the
CCS surface (vs. tiled main surface layout).
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 3d1adc3d64 ("drm/i915/adlp: Add support for remapping CCS FBs")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-5-imre.deak@intel.com
XE_LPD display adds support for display audio codec keepalive feature.
This feature works also when display codec is in D3 state and the audio
link is off (BCLK off). To enable this functionality, display driver
must update the AUD_TS_CDCLK_M/N registers whenever CDCLK is changed.
Actual timestamps are generated only when the audio codec driver
specifically enables the KeepAlive (KAE) feature.
This patch adds new hooks to intel_set_cdclk() in order to inform
display audio driver when CDCLK change is started and when it is
complete.
Bspec: 53679
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211021105915.4128635-1-kai.vehmanen@linux.intel.com
Looks like our VBIOS/GOP generally fail to turn the DP dual mode adater
TMDS output buffers back on after a reboot. This leads to a black screen
after reboot if we turned the TMDS output buffers off prior to reboot.
And if i915 decides to do a fastboot the black screen will persist even
after i915 takes over.
Apparently this has been a problem ever since commit b2ccb822d3 ("drm/i915:
Enable/disable TMDS output buffers in DP++ adaptor as needed") if one
rebooted while the display was turned off. And things became worse with
commit fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
since now we always turn the display off before a reboot.
This was reported on a RKL, but I confirmed the same behaviour on my
SNB as well. So looks pretty universal.
Let's fix this by explicitly turning the TMDS output buffers back on
in the encoder->shutdown() hook. Note that this gets called after irqs
have been disabled, so the i2c communication with the DP dual mode
adapter has to be performed via polling (which the gmbus code is
perfectly happy to do for us).
We also need a bit of care in handling DDI encoders which may or may
not be set up for HDMI output. Specifically ddc_pin will not be
populated for a DP only DDI encoder, in which case we don't want to
call intel_gmbus_get_adapter(). We can handle that by simply doing
the dual mode adapter type check before calling
intel_gmbus_get_adapter().
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4371
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029191802.18448-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
By using the modifier plane capability flags to encode the modifiers'
CCS type and tiling attributes, it becomes simpler to the check for
any of these capabilities when providing the list of supported
modifiers.
This also allows distinguishing modifiers on future platforms where
platforms with the same display version support different modifiers. An
example is DG2 and ADLP, both being D13, where DG2 supports only F and X
tiling, while ADLP supports only Y and X tiling. With the
INTEL_PLANE_CAP_TILING_* flags added in this patch we can provide
the correct modifiers for each platform.
v2:
- Define PLANE_HAS_* with macros instead of an enum. (Jani)
- Rename PLANE_HAS_*_ANY to PLANE_HAS_*_MASK. (Jani)
- Rename PLANE_HAS_* to INTEL_PLANE_CAP_*.
- Set the CCS_RC_CC cap only for DISPLAY_VER >= 12.
- Set the TILING_Y cap only for DISPLAY_VER < 13 || ADLP.
- Simplify the SKL plane cap display version checks and move them
to a separate function.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027125150.2891371-1-imre.deak@intel.com
Add FourCCs for 10- and 12-bit red formats with padding to 16 bits.
They correspond to the V4L2 10- and 12-bit greyscale (V4L2_PIX_FMT_Y10
and V4L2_PIX_FMT_Y12) formats, as well as the Bayer formats with the
same bit depth (V4L2_PIX_FMT_SBGGR{10,12} and all other Bayer pattern
permutations).
These formats are not used by any kernel driver at this point, but need
to be exposed to applications by libcamera, which uses DRM FourCCs for
pixel formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027233140.12268-1-laurent.pinchart@ideasonboard.com
Try to make bigjoiner pipes less special.
The main things here are that each pipe now does full
clock computation/readout with its own shared_dpll reference.
Also every pipe's cpu_transcoder always points correctly
at the master transcoder.
Due to the above changes state readout is now complete
and all the related hacks can go away. The actual modeset
sequence code is still a mess, but I think in order to clean
that up properly we're probably going to have to redesign
the modeset logic to treat transcoders vs. pipes separately.
That is going to require significant amounts of work.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-9-ville.syrjala@linux.intel.com
Let's disable planes on all pipes affected by the modeset before
we start doing the actual modeset. This means we have less
random planes enabled during the modeset, and it also mirrors
what we already do when enabling pipes on skl+ since we enable
planes on all pipes as the very last step. As a bonus we also
nuke a bunch og bigjoiner special casing.
I've occasionally pondered about going even furher here and
doing the pre_plane_update() stuff for all pipes first, then
actually disabling the planes, and finally running the rest
of the modeset sequence. This would potentially allow
parallelizing all the extra vblank waits across multiple pipes,
and would make the plane disable even more atomic. But let's
go one step a time here.
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Disabling planes in the middle of the modeset seuqnece does not make
sense since userspace can anyway disable planes before the modeset
even starts. So when the modeset seuqence starts the set of enabled
planes is entirely arbitrary. Trying to sprinkle the plane disabling
into the modeset sequence just means more randomness and potential
for hard to reproduce bugs.
So it makes most sense to just disable all planes first so that the
rest of the modeset sequence remains identical regardless of which
planes happen to be enabled by userspace at the time.
This reverts commit 84030adb9e.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
PSR2 apparently requires some planes to be enabled for some
silly reason, and so we are now trying to turn PSR off before
planes go off. Except during a full modeset that is handled
less clearly through reorganization of the modeset sequence.
That is not great as it makes the code mode complex, and
prevents us from doing nice things such as just turning off
all the planes at the very start of the modeset. So let's
move the PSR pre_plane_update() thing to a spot where it
will handle both full modesets and everything else.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-2-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Alderlake-P was getting 'max time under evasion' messages when PSR2
is enabled, this is due PIPE_SCANLINE/PIPEDSL returning 0 over a
period of time longer than VBLANK_EVASION_TIME_US.
For PSR1 we had the same issue so intel_psr_wait_for_idle() was
implemented to wait for PSR1 to get into idle state but nothing was
done for PSR2.
For PSR2 we can't only wait for idle state as PSR2 tends to keep
into sleep state(ready to send selective updates).
Waiting for any state below deep sleep proved to be effective in
avoiding the evasion messages and also not wasted a lot of time.
v2:
- dropping the additional wait_for loops, only the _wait_for_atomic()
is necessary
- waiting for states below EDP_PSR2_STATUS_STATE_DEEP_SLEEP
v3:
- dropping intel_wait_for_condition_atomic() function
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005231851.67698-1-jose.souza@intel.com
Some randconfig builds fail when drm/drm_bridge.h is not included
implicitly in this file:
drivers/gpu/drm/msm/dp/dp_parser.c:279:25: error: implicit declaration of function 'devm_drm_panel_bridge_add' [-Werror,-Wimplicit-function-declaration]
parser->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
Fixes: 4b296d15b3 ("drm/msm/dp: Allow attaching a drm_panel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211026083254.3396322-1-arnd@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clang warns:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:162:6: error: variable 'commit' is uninitialized when used here [-Werror,-Wuninitialized]
if (commit)
^~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:106:32: note: initialize the variable 'commit' to silence this warning
struct drm_crtc_commit *commit;
^
= NULL
1 error generated.
The assignment and use of commit in the main body of
dpu_crtc_set_crc_source() were removed from v1 to v2 but the call to
drm_crtc_commit_put() at the end was not. Do that now so there is no
more warning.
Fixes: 78d9b458cc ("drm/msm/dpu: Add CRC support for DPU")
Link: https://github.com/ClangBuiltLinux/linux/issues/1493
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211026142435.3606413-1-nathan@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
8b/10b encoding format requires to reserve the first slot for
recording metadata. Real data transmission starts from the second slot,
with a total of available 63 slots available.
In 128b/132b encoding format, metadata is transmitted separately
in LLCP packet before MTP. Real data transmission starts from
the first slot, with a total of 64 slots available.
v2:
* Move total/start slots to mst_state, and copy it to mst_mgr in
atomic_check
v3:
* Only keep the slot info on the mst_state
* add a start_slot parameter to the payload function, to facilitate non
atomic drivers (this is a temporary workaround and should be removed when
we are moving out the non atomic driver helpers)
v4:
*fixed typo and formatting
v5: (no functional changes)
* Fixed formatting in drm_dp_mst_update_slots()
* Reference mst_state instead of mst_state->mgr for debugging info
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
[v5 nitpicks]
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-3-lyude@redhat.com
Commit 110860541f ("mm/secretmem: use refcount_t instead of atomic_t")
attempted to fix the problem of secretmem_users wrapping to zero and
allowing suspend once again.
But it was reverted in commit 87066fdd2e ("Revert 'mm/secretmem: use
refcount_t instead of atomic_t'") because of the problems it caused - a
refcount_t was not semantically the right type to use.
Instead prevent secretmem_users from wrapping to zero by forbidding new
users if the number of users has wrapped from positive to negative.
This stops a long way short of reaching the necessary 4 billion users
where it wraps to zero again, so there's no need to be clever with
special anti-wrap types or checking the return value from atomic_inc().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Jordy Zomer <jordy@pwning.systems>
Cc: Kees Cook <keescook@chromium.org>,
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit efafec27c5 ("spi: Fix tegra20 build with CONFIG_PM=n") already
fixed the build without PM support once. There was an alternative fix
by Guenter in commit 2bab94090b ("spi: tegra20-slink: Declare runtime
suspend and resume functions conditionally"), and Mark then merged the
two correctly in ffb1e76f4f ("Merge tag 'v5.15-rc2' into spi-5.15").
But for some inexplicable reason, Mark then merged things _again_ in
commit 59c4e190b1 ("Merge tag 'v5.15-rc3' into spi-5.15"), and screwed
things up at that point, and the __maybe_unused attribute on
tegra_slink_runtime_resume() went missing.
Reinstate it, so that alpha (and other architectures without PM support)
builds cleanly again.
Btw, this is another prime example of how random back-merges are not
good. Just don't do them. Subsystem developers should not merge my
tree in any normal circumstances. Both of those merge commits pointed
to above are bad: even the one that got the merge result right doesn't
even mention _why_ it was done, and the one that got it wrong is
obviously broken.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
- Fix clang-related relocation warning in futex code
- Fix incorrect use of get_kernel_nofault()
- Fix bad code generation in __get_user_check() when kasan is enabled
- Ensure TLB function table is correctly aligned
- Remove duplicated string function definitions in decompressor
- Fix link-time orphan section warnings
- Fix old-style function prototype for arch_init_kprobes()
- Only warn about XIP address when not compile testing
- Handle BE32 big endian for keystone2 remapping
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9148/1: handle CONFIG_CPU_ENDIAN_BE32 in arch/arm/kernel/head.S
ARM: 9141/1: only warn about XIP address when not compile testing
ARM: 9139/1: kprobes: fix arch_init_kprobes() prototype
ARM: 9138/1: fix link warning with XIP + frame-pointer
ARM: 9134/1: remove duplicate memcpy() definition
ARM: 9133/1: mm: proc-macros: ensure *_tlb_fns are 4B aligned
ARM: 9132/1: Fix __get_user_check failure with ARM KASAN images
ARM: 9125/1: fix incorrect use of get_kernel_nofault()
ARM: 9122/1: select HAVE_FUTEX_CMPXCHG
Pull libata fix from Damien Le Moal:
"A single fix in this pull request addressing an invalid error code
return in the sata_mv driver (from Zheyu)"
* tag 'libata-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: sata_mv: Fix the error handling of mv_chip_id()
Pull pin control fixes from Linus Walleij:
"Some late pin control fixes, the most generally annoying will probably
be the AMD IRQ storm fix affecting the Microsoft surface.
Summary:
- Three fixes pertaining to Broadcom DT bindings. Some stuff didn't
work out as inteded, we need to back out
- A resume bug fix in the STM32 driver
- Disable and mask the interrupts on probe in the AMD pinctrl driver,
affecting Microsoft surface"
* tag 'pinctrl-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: amd: disable and mask interrupts on probe
pinctrl: stm32: use valid pin identifier in stm32_pinctrl_resume()
Revert "pinctrl: bcm: ns: support updated DT binding as syscon subnode"
dt-bindings: pinctrl: brcm,ns-pinmux: drop unneeded CRU from example
Revert "dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon"
