The lpfc driver is calling get_device and put_device on scsi_fc_transport
device structure. When this code was removed, the driver triggered an oops
in "scsi_is_host_dev" when the first SCSI target was unregistered from the
transport.
The reason the calls were necessary is that the driver is calling
scsi_remove_host too early, before the target rports are unregistered and
the scsi devices disconnected from the scsi_host. The fc_host was torn
down during fc_remove_host.
Fix by moving the lpfc_pci_remove_one_s3/s4 calls to scsi_remove_host to
after the nodes are cleaned up. Remove the get_device and put_device calls
and the supporting code.
Link: https://lore.kernel.org/r/20201115192646.12977-4-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the driver has gone to a normal ref interface (with no odd logic)
the discovery logic needs to be updated to reworked so that it properly
takes references when it should and give them up when it should.
Rework the driver for the following get/put model:
- Move gets to just before an I/O is issued. Add gets for places where an
I/O was issued without one.
- Ensure that failures from lpfc_nlp_get() are handled by the driver.
- Check and fix the placement of lpfc_nlp_puts relative to io completions.
Note: some of these paths may not release the reference on the exact io
completion as the reference is held as the code takes another step in
the discovery thread and which may cause another io to be issued.
- Rearrange some code for error processing and calling lpfc_nlp_put.
- Fix some places of incorrect reference freeing that was causing the
premature releasing of the structure.
- Nvmet plogi handling performs unreg_rpi's. The reference counts were
unbalanced resulting in premature node removal. In some cases this
caused loss of node discovery. Corrected the reftaking around nvmet
plogis.
Nodes that experience devloss now get released from the node list now that
there is a proper reference taking.
Link: https://lore.kernel.org/r/20201115192646.12977-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a remote port is disconnected and disappears, its node structure
(ndlp) stays allocated and on a vport node list. While on the list it can
be matched, thus requires validation checks on state to be added in
numerous code paths. If the node comes back, its possible for there to be
multiple node structures for the same device on the vport node list. There
is no reason to keep the node structure around after it is no longer in
existence, and the current implementation creates problems for itself
(multiple nodes) and lots of unnecessary code for state validation.
Additionally, the reference taking on the node structure didn't follow the
normal model used by the kernel kref api. It included lots of odd logic to
match state with reference count. The combination of this odd logic plus
the way it was implicitly used in the discovery engine made its reference
taking implementation suspect and extremely hard to follow.
Change the driver such that the reference taking routines are now normal
ref increments/decrements and callout on refcount=0.
With this in place, the rework can be done such that the node structure is
fully removed and deallocated when the remote port no longer exists and all
references are removed. This removal logic, and the basic ref counting are
intrically tied, thus in a single patch.
Link: https://lore.kernel.org/r/20201115192646.12977-2-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/hpsa.c: In function ‘hpsa_volume_offline’:
drivers/scsi/hpsa.c:3885:5: warning: variable ‘scsi_status’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c:3884:6: warning: variable ‘cmd_status’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_update_scsi_devices’:
drivers/scsi/hpsa.c:4354:9: warning: variable ‘n_ext_target_devs’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_scatter_gather’:
drivers/scsi/hpsa.c:4583:36: warning: variable ‘last_sg’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_init_one’:
drivers/scsi/hpsa.c:8639:6: warning: variable ‘dac’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_enter_performant_mode’:
drivers/scsi/hpsa.c:9300:7: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201112101929.GC1997862@dell
Cc: Don Brace <don.brace@microchip.com>
Cc: Bugfixes to <esc.storagedev@microsemi.com>
Cc: storagedev@microchip.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current implementation of scsi_vpd_lun_id() uses the designator length
as an implicit measure of priority. This works most of the time, but not
always. For example, some Hitachi storage arrays return this in VPD 0x83:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: T10 vendor identification, code_set: ASCII
associated with the Addressed logical unit
vendor id: HITACHI
vendor specific: 5030C3502025
Designation descriptor number 2, descriptor length: 6
designator_type: vendor specific [0x0], code_set: Binary
associated with the Target port
vendor specific: 08 03
Designation descriptor number 3, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the Addressed logical unit
NAA 6, IEEE Company_id: 0x60e8
Vendor Specific Identifier: 0x7c35000
Vendor Specific Identifier Extension: 0x30c35000002025
[0x60060e8007c350000030c35000002025]
The current code would use the first descriptor because it's longer than
the NAA descriptor. But this is wrong, the kernel is supposed to prefer NAA
descriptors over T10 vendor ID. Designator length should only be used to
compare designators of the same type.
This patch addresses the issue by separating designator priority and
length.
Link: https://lore.kernel.org/r/20201029170846.14786-1-mwilck@suse.com
Fixes: 9983bed390 ("scsi: Add scsi_vpd_lun_id()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS proprietary features (including features introduced later) in MediaTek
UFS platforms have complicated combinations among different platforms.
To ease code readability and maintenance, decouple all proprietary features
from platform bindings. Each feature would be enabled only if specific
property string is defined in device tree node.
Link: https://lore.kernel.org/r/20201029115750.24391-4-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever we encounter a sense code of ALUA transitioning in
scsi_io_completion() it means that the SCSI midlayer ran out of retries
trying to wait for ALUA transitioning. In these cases we should be passing
up the error, but signalling that the I/O might be retried, preferably on
another path. So return BLK_STS_AGAIN in these cases.
[mkp: typo + fallthrough]
Link: https://lore.kernel.org/r/20200930080256.90964-5-hare@suse.de
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be setting the 'transitioning' ALUA state once we get a Unit
Attention indicating the array is in transitioning. There are arrays which
cannot respond to an RTPG while in transitioning, and others have issues
correctly reporting the state. So better to set the state during Unit
Attention handling and wait for TUR / RTPG to run its course.
Link: https://lore.kernel.org/r/20200930080256.90964-4-hare@suse.de
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the ALUA state indicates transitioning we should not retry the command
immediately, but rather complete the command with BLK_STS_AGAIN to signal
the completion handler that it might be retried. This allows multipathing
to redirect the command to another path if possible, and avoid stalls
during lengthy transitioning times.
Link: https://lore.kernel.org/r/20200930080256.90964-3-hare@suse.de
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/dc395x.c: In function ‘data_io_transfer’:
drivers/scsi/dc395x.c:2400:16: warning: variable ‘data2’ set but not used [-Wunused-but-set-variable]
drivers/scsi/dc395x.c:2400:6: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
drivers/scsi/dc395x.c: In function ‘reselect’:
drivers/scsi/dc395x.c:2992:5: warning: variable ‘arblostflag’ set but not used [-Wunused-but-set-variable]
drivers/scsi/dc395x.c: In function ‘doing_srb_done’:
drivers/scsi/dc395x.c:3393:28: warning: variable ‘dir’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201102142359.561122-18-lee.jones@linaro.org
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Ali Akcaagac <aliakc@web.de>
Cc: Jamie Lenehan <lenehan@twibble.org>
Cc: "C.L. Huang" <ching@tekram.com.tw>
Cc: Erich Chen <erich@tekram.com.tw>
Cc: Kurt Garloff <garloff@suse.de>
Cc: dc395x@twibble.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/advansys.c: In function ‘asc_prt_asc_board_eeprom’:
drivers/scsi/advansys.c:2879:15: warning: variable ‘asc_dvc_varp’ set but not used [-Wunused-but-set-variable]
drivers/scsi/advansys.c: In function ‘asc_prt_driver_conf’:
drivers/scsi/advansys.c:3174:6: warning: variable ‘chip_scsi_id’ set but not used [-Wunused-but-set-variable]
drivers/scsi/advansys.c: In function ‘AdvISR’:
drivers/scsi/advansys.c:6114:9: warning: variable ‘target_bit’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201102142359.561122-17-lee.jones@linaro.org
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/esas2r/esas2r_main.c:911: warning: Function parameter or member 'a' not described in 'esas2r_check_active_queue'
drivers/scsi/esas2r/esas2r_main.c:911: warning: Function parameter or member 'abort_request' not described in 'esas2r_check_active_queue'
drivers/scsi/esas2r/esas2r_main.c:911: warning: Function parameter or member 'cmd' not described in 'esas2r_check_active_queue'
drivers/scsi/esas2r/esas2r_main.c:911: warning: Function parameter or member 'queue' not described in 'esas2r_check_active_queue'
Link: https://lore.kernel.org/r/20201102142359.561122-16-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Function parameter or member 'ctx_buf' not described in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'ctxp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'mp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'targetport' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'phba' not described in 'lpfc_nvmet_invalidate_host'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvmet_invalidate_host'
Link: https://lore.kernel.org/r/20201102142359.561122-15-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/esas2r/esas2r_int.c: In function ‘esas2r_doorbell_interrupt’:
drivers/scsi/esas2r/esas2r_int.c:692:22: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/scsi/esas2r/esas2r_int.c: In function ‘esas2r_send_reset_ae’:
drivers/scsi/esas2r/esas2r_int.c:868:44: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
Link: https://lore.kernel.org/r/20201102142359.561122-14-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_nvme.c:256: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Excess function parameter 'nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1594: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2193: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20201102142359.561122-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'phba' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'pring' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:1484: warning: Function parameter or member 'cmp' not described in 'lpfc_issue_ct_rsp'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'nemb_tp' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Function parameter or member 'job' not described in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Excess function parameter 'dmabuf' description in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4474: warning: Function parameter or member 'job' not described in 'lpfc_bsg_write_ebuf_set'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Function parameter or member 'job' not described in 'lpfc_bsg_issue_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Excess function parameter 'mb' description in 'lpfc_bsg_issue_mbox'
Link: https://lore.kernel.org/r/20201102142359.561122-8-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_debugfs.c:4204: warning: Function parameter or member 'len' not described in 'lpfc_idiag_queacc_read_qe'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Function parameter or member 'ctlregid' not described in 'lpfc_idiag_ctlacc_read_reg'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Excess function parameter 'drbregid' description in 'lpfc_idiag_ctlacc_read_reg'
Link: https://lore.kernel.org/r/20201102142359.561122-7-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4165:3:
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2792: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwpn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'attr' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Excess function parameter 'cdev' description in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'vpt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'tgt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Excess function parameter 'ndlp' description in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3264: warning: Function parameter or member 'lun_pri' not described in 'lpfc_oas_lun_get_next'
drivers/scsi/lpfc/lpfc_attr.c:3302: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_change'
drivers/scsi/lpfc/lpfc_attr.c:3376: warning: Function parameter or member 'count' not described in 'lpfc_oas_lun_store'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Function parameter or member 'vport' not described in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Excess function parameter 'phba' description in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'dev' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'attr' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'buf' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'count' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'phba' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'val' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4148: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_store'
drivers/scsi/lpfc/lpfc_attr.c:4302: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_show'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Function parameter or member 'buf' not described in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Excess function parameter 'buff' description in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'dev' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'attr' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'buf' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'count' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'phba' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'val' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:7117: warning: Function parameter or member 'verbose' not described in 'lpfc_hba_log_verbose_init'
Link: https://lore.kernel.org/r/20201102142359.561122-6-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel-doc does not understand this use-case.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4164:3:
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'dev' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'buf' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'dev' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'buf' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'attr' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'default' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'minval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'maxval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'phba' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'val' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'attr' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'default' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'minval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'maxval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'phba' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'val' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'dev' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'buf' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'count' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'val' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'cdev' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'count' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'field' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'format_string' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'sz' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'cast' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'cdev' description in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'buf' description in 'lpfc_rport_show_function'
Link: https://lore.kernel.org/r/20201102142359.561122-5-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:507: warning: Function parameter or member 'idx' not described in 'lpfc_sli4_io_xri_aborted'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:986: warning: Function parameter or member 'new_guard' not described in 'lpfc_bg_err_inject'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'txop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'rxop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'txopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'rxopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'txop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'rxop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'txopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'rxopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:2131: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl_prot'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Function parameter or member 't' not described in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Excess function parameter 'ptr' description in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Function parameter or member 'shost' not described in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Excess function parameter 'done' description in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Function parameter or member 'cmnd' not described in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Excess function parameter 'rdata' description in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'phba' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'pri' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Excess function parameter 'pha' description in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Function parameter or member 'phba' not described in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Excess function parameter 'pha' description in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Function parameter or member 'phba' not described in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Excess function parameter 'pha' description in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'phba' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'found_lun_pri' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Excess function parameter 'pha' description in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'phba' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'pri' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Excess function parameter 'pha' description in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'phba' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'pri' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Excess function parameter 'pha' description in 'lpfc_disable_oas_lun'
Link: https://lore.kernel.org/r/20201102142359.561122-4-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This string is not NUL terminated.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/pm8001/pm8001_sas.c:41:
In function ‘strncpy’,
inlined from ‘pm8001_issue_ssp_tmf’ at drivers/scsi/pm8001/pm8001_sas.c:919:2:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ specified bound 8 equals destination size [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20201102102544.1018706-2-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI strings like inqdata are not NUL terminated.
Fixes the following W=1 kernel build warning(s):
In file included from include/linux/bitmap.h:9,
from include/linux/nodemask.h:95,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:6,
from include/linux/umh.h:4,
from include/linux/kmod.h:9,
from include/linux/module.h:16,
from drivers/scsi/arcmsr/arcmsr_hba.c:47:
In function ‘strncpy’,
inlined from ‘arcmsr_handle_virtual_command’ at drivers/scsi/arcmsr/arcmsr_hba.c:3055:3:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ output truncated before terminating nul copying 4 bytes from a string of the same length [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
In function ‘strncpy’,
inlined from ‘arcmsr_handle_virtual_command’ at drivers/scsi/arcmsr/arcmsr_hba.c:3053:3:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ output truncated before terminating nul copying 16 bytes from a string of the same length [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
In function ‘strncpy’,
inlined from ‘arcmsr_handle_virtual_command’ at drivers/scsi/arcmsr/arcmsr_hba.c:3051:3:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ output truncated before terminating nul copying 8 bytes from a string of the same length [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20201102102544.1018706-1-lee.jones@linaro.org
Cc: support@areca.com.tw
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
DeepSleep is a UFS v3.1 feature that achieves the lowest power consumption
of the device, apart from power off.
In DeepSleep mode, no commands are accepted, and the only way to exit is
using a hardware reset or power cycle.
This patch assumes that if a power cycle was an option, then power off
would be preferable, so only exit via a hardware reset is supported.
Drivers that wish to support DeepSleep need to set a new capability flag
UFSHCD_CAP_DEEPSLEEP and provide a hardware reset via the existing
->device_reset() callback.
It is assumed that UFS devices with wspecversion >= 0x310 support
DeepSleep.
[mkp: dropped sysfs ABI doc due to conflicts]
Link: https://lore.kernel.org/r/20201103141403.2142-2-adrian.hunter@intel.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A use-after-free or null-pointer error occurs when the 251-byte response
data is copied from IOMB buffer to response message buffer in function
pm8001_mpi_get_nvmd_resp().
After sending the command get_nvmd_data(), the caller begins to sleep by
calling wait_for_complete() and waits for the wake-up from calling
complete() in pm8001_mpi_get_nvmd_resp(). Due to unexpected events (e.g.,
interrupt), if response buffer gets freed before memcpy(), a use-after-free
error will occur. To fix this, the complete() should be called after
memcpy().
Link: https://lore.kernel.org/r/20201102165528.26510-5-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
