Like we do for encoder let's make the plane->get_hw_state() return
the pipe to which the plane is currently attached. We don't currently
allow planes to move between the pipes, but perhaps one day we will.
In either case this makes the code more uniform and perhaps makes
intel_plane_mapping_ok() slightly more clear.
Note that for i965 and g4x planes A and B still have pipe select bits
but they're hardwired to pipe A and B respectively. This means we can
safely interpret those bits just like on gen2/3. This allows the
same readout code work for plane C (which can still be assigned
to eiter pipe on i965) should we ever expose it.
g4x no longer allows moving the cursor planes between the pipes,
but the pipe select bits can still be set in the register. Thus
we have to ignore those bits. OTOH i965 still allows the cursors
to move between pipes thus we have to trust the bits there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
During testing we encounter a conflict between SUSPEND_TEST_DEVICES and
disabling reset (gem_eio/suspend). This results in the device continuing
on without being reset, but since it has gone through HW sanitization to
account for the suspend/resume cycle, we have to assume the device has
been reset to its defaults. A simple way around this is to skip the
sanitize phase for SUSPEND_TEST_DEVICES by moving it to suspend-late.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180531082246.9763-4-chris@chris-wilson.co.uk
During suspend we want to flush out all active contexts and their
rendering. To do so we queue a request from the kernel's context, once
we know that request is done, we know the GPU is completely idle. To
speed up that switch bump the GPU clocks.
Switching to the kernel context prior to idling is also used to enforce
a barrier before changing OA properties, and when evicting active
rendering from the global GTT. All cases where we do want to
race-to-idle.
v2: Limit the boosting to only the switch before suspend.
v3: Limit it to the wait-for-idle on suspend.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: David Weinehall <david.weinehall@linux.intel.com> #v1
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180531082246.9763-2-chris@chris-wilson.co.uk
Since we use i915_gem_find_active_request() from inside
intel_engine_dump() and may call that at any time, we do not guarantee
that the engine is paused nor that the signal kthreads and irq handler
are suspended, so we cannot assert that the breadcrumb doesn't advance
and that the irq hasn't happened on another CPU signaling the request we
believe to be idle.
The second assert removed (that request->engine == engine) remains
valid, but is now more rigorously checked during retirement.
Fixes: f636edb214 ("drm/i915: Make i915_engine_info pretty printer to standalone")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180529132922.6831-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
DPCD 2009h "Synchronization latency in sink" has bits that tell us the
maximum number of frames sink can take to resynchronize to source timing
when exiting PSR. More importantly, as per eDP 1.4b, this is the "Minimum
number of frames following PSR exit that the Source device needs to
wait for PSR entry."
We currently use this value only to setup the number frames to wait before
PSR2 selective update. But, based on the above description it makes more
sense to use this to configure idle frames for both PSR1 and and PSR2. This
will ensure we wait the required number of frames before
activation whether it is PSR1 or PSR2.
The minimum number of idle frames remains 6, while allowing sink
synchronization latency and VBT to increase this value.
This also solves the flip-flop between sink and source frames that I
noticed on my Thinkpad X260 during PSR exit. This specific panel has a
value of 8h, which according to the spec means the "Source device must
wait for more than eight active frames after PSR exit before initiating PSR
entry. (In this case, should be provided by the panel supplier.)" VBT
however has a value of 0.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525033047.7596-1-dhinakaran.pandiyan@intel.com
Let's suppress the underruns around every modeset sequence instead
of trying to avoid it. Planes are disabled at this point anyway so
we don't really gain anything from keeping the underrun reporting
enabled. Also for PCH ports we already suppress all underruns here
anyway so trying avoid it for the CPU eDP doesn't seem all that
important.
Maybe this gets rid of some lingering spurious underruns?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524190406.2973-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
VBT seems to have some bits to tell us whether the internal LVDS port
has something hooked up. In theory one might expect the VBT to not have
a child device for the LVDS port if there's no panel hooked up, but
in practice many VBTs still add the child device. The "LVDS config" bits
seem more reliable though, so let's check those.
So far we've used the "LVDS config" bits to check for eDP support on
ILK+, and disable the internal LVDS when the value is 3. That value
is actually documented as "Both internal LVDS and SDVO LVDS", but in
practice it looks to mean "eDP" on all the ilk+ VBTs I've seen. So let's
keep that interpretation, but for pre-ILK we will consider the value
3 to also indicate the presence of the internal LVDS.
Currently we have 25 DMI matches for the "no internal LVDS" quirk. In an
effort to reduce that let's toss in a WARN when the DMI match and VBT
both tell us that the internal LVDS is not present. The hope is that
people will report a bug, and then we can just nuke the corresponding
entry from the DMI quirk list. Credits to Jani for this idea.
v2: Split the basic int_lvds_support thing to a separate patch (Jani)
v3: Rebase
v4: Limit this to VBT version >= 134
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518150138.18361-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
In order to prepare the GPU for sleeping, we may want to submit commands
to it. This is a complicated process that may even require some swapping
in from shmemfs, if the GPU was in the wrong state. As such, we need to
do this preparation step synchronously before the rest of the system has
started to turn off (e.g. swapin fails if scsi is suspended).
Fortunately, we are provided with a such a hook, pm_ops.prepare().
v2: Compile cleanup
v3: Fewer asserts, fewer problems?
v4: Ville pointed out that in some circumstances (such as switching off
the overlay) the display code may issue a GPU request. This is
unexpected, and will result in us going to sleep with us believing the
GPU is still awake (though all user work has been saved). Add a comment
to remind our future selves of what trouble brews.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106640
Testcase: igt/drv_suspend after igt/gem_tiled_swapping
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525092629.1456-1-chris@chris-wilson.co.uk
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
We were not very carefully checking to see if an older request on the
engine was an earlier switch-to-kernel-context before deciding to emit a
new switch. The end result would be that we could get into a permanent
loop of trying to emit a new request to perform the switch simply to
flush the existing switch.
What we need is a means of tracking the completion of each timeline
versus the kernel context, that is to detect if a more recent request
has been submitted that would result in a switch away from the kernel
context. To realise this, we need only to look in our syncmap on the
kernel context and check that we have synchronized against all active
rings.
v2: Since all ringbuffer clients currently share the same timeline, we do
have to use the gem_context to distinguish clients.
As a bonus, include all the tracing used to debug the death inside
suspend.
v3: Test, test, test. Construct a selftest to exercise and assert the
expected behaviour that multiple switch-to-contexts do not emit
redundant requests.
Reported-by: Mika Kuoppala <mika.kuoppala@intel.com>
Fixes: a89d1f921c ("drm/i915: Split i915_gem_timeline into individual timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524081135.15278-1-chris@chris-wilson.co.uk
PSR hardware and hence the driver code for VLV and CHV deviates a lot from
their DDI counterparts. While the feature has been disabled for a long time
now, retaining support for these platforms is a maintenance burden. There
have been multiple refactoring commits to just keep the existing code for
these platforms in line with the rest. There are known issues that need to
be fixed to enable PSR on these platforms, and there is no PSR capable
platform in CI to ensure the code does not break again if we get around to
fixing the existing issues. On account of all these reasons, let's nuke
this code for now and bring it back if a need arises in the future.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511230059.19387-1-dhinakaran.pandiyan@intel.com
For psr block #9, the vbt description has moved to options [0-3] for
TP1,TP2,TP3 Wakeup time from decimal value without any change to vbt
structure. Since spec does not mention from which VBT version this
change was added to vbt.bsf file, we cannot depend on bdb->version check
to change for all the platforms.
There is RCR inplace for GOP team to provide the version number
to make generic change. Since Kabylake with bdb version 209 is having this
change, limiting this change to gen9_bc and version 209+ to unblock google.
Tested on skl(bdb version 203,without options) and
kabylake(bdb version 209,212) having new options.
bspec 20131
v2: (Jani and Rodrigo)
move the 165 version check to intel_bios.c
v3: Jani
Move the abstraction to intel_bios.
v4: Jani
Rename tp*_wakeup_time to have "us" suffix.
For values outside range[0-3],default to max 2500us.
Old decimal value was wake up time in multiples of 100us.
v5: Jani and Rodrigo
Handle option 2 in default condition.
Print oustide range value.
For negetive values default to 2500us.
v6: Jani
Handle default first and then fall through for case 2.
v7: Rodrigo
Apply this change for IS_GEN9_BC and vbt version > 209
v8: Puthik
Add new function vbt_psr_to_us.
v9: Jani
Change to v7 version as it's more readable.
DK
add comment /*fall through*/ after case2.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Puthikorn Voravootivat <puthik@chromium.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526981243-2745-1-git-send-email-vathsala.nagaraju@intel.com
L3Bank could be fused off in hardware for debug purpose, and it
is possible that subslice is enabled while its corresponding L3Bank pairs
are disabled. In such case, if MCR packet control register(0xFDC) is
programed to point to a disabled bank pair, a MMIO read into L3Bank range
will return 0 instead of correct values.
However, this is not going to be the case in any production silicon.
Therefore, we only check at initialization and issue a warning should
this really happen.
References: HSDES#1405586840
v2:
- use fls instead of find_last_bit (Chris)
- use is_power_of_2() instead of counting bit set (Chris)
v3:
- rebase on latest tip
v5:
- Added references (Mika)
- Move local variable into scope where they are used (Ursulin)
- use a new local variable to reduce long line of code (Ursulin)
v6:
- Some coding style and use more local variables for clearer
logic (Ursulin)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Yunwei Zhang <yunwei.zhang@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526683285-24861-1-git-send-email-yunwei.zhang@intel.com
WaProgramMgsrForCorrectSliceSpecificMmioReads dictate that before any MMIO
read into Slice/Subslice specific registers, MCR packet control
register(0xFDC) needs to be programmed to point to any enabled
slice/subslice pair. Otherwise, incorrect value will be returned.
However, that means each subsequent MMIO read will be forwarded to a
specific slice/subslice combination as read is unicast. This is OK since
slice/subslice specific register values are consistent in almost all cases
across slice/subslice. There are rare occasions such as INSTDONE that this
value will be dependent on slice/subslice combo, in such cases, we need to
program 0xFDC and recover this after. This is already covered by
read_subslice_reg.
Also, 0xFDC will lose its information after TDR/engine reset/power state
change.
References: HSD#1405586840, BSID#0575
v2:
- use fls() instead of find_last_bit() (Chris)
- added INTEL_SSEU to extract sseu from device info. (Chris)
v3:
- rebase on latest tip
v5:
- Added references (Mika)
- Change the ordered of passing arguments and etc. (Ursulin)
v7:
- Moved WA explanation Comments(Oscar)
- Rebased.
v8:
- Renamed sanitize_mcr to calculate_s_ss_select. (Oscar)
- calculate s/ss selector instead of whole mcr. (Oscar)
v9:
- Updated function name (Oscar)
- Remove redundant variables (Oscar)
v10:
- Separate pre-GEN10 and GEN11 mask. (Oscar)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Yunwei Zhang <yunwei.zhang@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526683197-24656-1-git-send-email-yunwei.zhang@intel.com
'Pipe CSC enable' bit is more than just deprecated in ICL+, it was
disabled in commit 077ef1f09c ("drm/i915/icl: Don't set pipe
CSC/Gamma in PLANE_COLOR_CTL") for primary and sprite planes as it was
causing those planes to be rendered as always black but it was not
disabled in cursor plane, also causing it to be rendered as black.
As mentioned in the commit referenced above, this is a workaround
too and the CSC and gamma per plane values needs to be setup before
enable CSC and gamma again.
BSpec: 4278 and 7635
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518201547.15793-1-jose.souza@intel.com
