rv3028_clkout_set_rate unconditionally sets RV3028_CLKOUT_CLKOE but
clk_set_rate may be called with the clock disabled. Ensure the clock is
kept disabled if it was not yet enabled.
Also, the actual rate was overwritten when enabling the clock, properly
write to the register only once.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-1-alexandre.belloni@bootlin.com
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits
(7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance
reads:
"To prevent accidental enabling, only a pattern on 1010 enables the
trickle charger. All other patterns disable the trickle charger."
Since not all RTCs connected to a backup battery or supercap use these
bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger
setups unconditionally.
Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1",
"SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4.
DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that
apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So
apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which
is used by both RTCs.
[1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf
[2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
Some RTCs can be equipped with a chargeable battery or supercap.
Every RTC allowing this whose driver's implement it are charged by
default. To disable this the trickle-diode-disable flag exists.
If a driver did not support charging and some time later one wants to
add that feature, there is currently no way to do it without breaking
dt backwards compatibility. RTCs on boards without the
trickle-diode-disable flag in their device tree would suddenly charge
their battery/supercap which is a change in behavior.
Change that by introducing aux-voltage-chargeable, not as a flag but as
a uint32 enum allowing to set "do not charge" (0) or "charge" (1). This
dt property is optional, so we can now distinguish these cases.
Care must be taken to support the old behavior for device trees without
aux-voltage-chargeable nonetheless to stay compatible.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200917183246.19446-2-bst@pengutronix.de
The way the driver is implemented is buggy for the (admittedly unlikely)
use case where there are two RTCs with one having an interrupt configured
and the second not. This is caused by the fact that we use a global
rtc_class_ops struct which we modify depending on whether the irq number
is present or not.
Fix it by using two const ops structs with and without alarm operations.
While at it: not being able to request a configured interrupt is an error
so don't ignore it and bail out of probe().
Fixes: ed13d89b08 ("rtc: Add Epson RX8010SJ RTC driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200914154601.32245-2-brgl@bgdev.pl
rs5c313_rtc_init() calls platform_driver_register(), and initializes the
hardware. This is wrong because of two reasons:
1. As soon as the driver has been registered, the device may be
probed. If devm_rtc_device_register() is called before hardware
initialization, reading the current time will fail:
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: registered as rtc0
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: hctosys: unable to read the hardware clock
2. If the platform device does not exist, the driver will still write
to a hardware device that may not be present.
Fix this by moving the hardware initialization sequence to the driver's
.probe() method.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814110731.29029-3-geert+renesas@glider.be
cmos_read_alarm() may leave certain fields of a struct rtc_wkalrm
untouched; therefore, these fields contain garbage if not properly
initialized, leading to inconsistent values when converting into
time64_t. This patch to zero initialize the struct before calling
cmos_read_alarm().
Note that this patch is not intended to produce a correct time64_t, it
is only to produce a consistent value. In the case of suspend/resume, a
correct time64_t is not necessary; a consistent value is sufficient to
correctly perform an equality test for t_current_expires and
t_saved_expires. Logic to deduce a correct time64_t is expensive and
hence should be avoided.
Signed-off-by: Victor Ding <victording@google.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814191654.v2.1.Iaf7638a2f2a87ff68d85fcb8dec615e41340c97f@changeid
Pull io_uring fixes from Jens Axboe:
"A few differerent things in here.
Seems like syzbot got some more io_uring bits wired up, and we got a
handful of reports and the associated fixes are in here.
General fixes too, and a lot of them marked for stable.
Lastly, a bit of fallout from the async buffered reads, where we now
more easily trigger short reads. Some applications don't really like
that, so the io_read() code now handles short reads internally, and
got a cleanup along the way so that it's now easier to read (and
documented). We're now passing tests that failed before"
* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
io_uring: short circuit -EAGAIN for blocking read attempt
io_uring: sanitize double poll handling
io_uring: internally retry short reads
io_uring: retain iov_iter state over io_read/io_write calls
task_work: only grab task signal lock when needed
io_uring: enable lookup of links holding inflight files
io_uring: fail poll arm on queue proc failure
io_uring: hold 'ctx' reference around task_work queue + execute
fs: RWF_NOWAIT should imply IOCB_NOIO
io_uring: defer file table grabbing request cleanup for locked requests
io_uring: add missing REQ_F_COMP_LOCKED for nested requests
io_uring: fix recursive completion locking on oveflow flush
io_uring: use TWA_SIGNAL for task_work uncondtionally
io_uring: account locked memory before potential error case
io_uring: set ctx sq/cq entry count earlier
io_uring: Fix NULL pointer dereference in loop_rw_iter()
io_uring: add comments on how the async buffered read retry works
io_uring: io_async_buf_func() need not test page bit
Commit 1355c31eeb ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.
Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.
Fixes: 1355c31eeb ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.ee
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block fixes from Jens Axboe:
"A few fixes on the block side of things:
- Discard granularity fix (Coly)
- rnbd cleanups (Guoqing)
- md error handling fix (Dan)
- md sysfs fix (Junxiao)
- Fix flush request accounting, which caused an IO slowdown for some
configurations (Ming)
- Properly propagate loop flag for partition scanning (Lennart)"
* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
block: fix double account of flush request's driver tag
loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
rnbd: no need to set bi_end_io in rnbd_bio_map_kern
rnbd: remove rnbd_dev_submit_io
md-cluster: Fix potential error pointer dereference in resize_bitmaps()
block: check queue's limits.discard_granularity in __blkdev_issue_discard()
md: get sysfs entry after redundancy attr group create
Pull RISC-V fix from Palmer Dabbelt:
"I collected a single fix during the merge window: we managed to break
the early trap setup on !MMU, this fixes it"
* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Setup exception vector for nommu platform
