Fix a wrong email address. It's only used in a comment, but it's easy
enough to fix.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Artem reported that the CPU load was 100% when capturing from
vivid at low resolution with ffmpeg.
This was caused by:
while (time_is_after_jiffies(cur_jiffies + wait_jiffies) &&
!kthread_should_stop())
schedule();
If there are no other processes running that can be scheduled,
then this is basically a busy-loop.
Change it to wait_event_interruptible_timeout() which doesn't
have that problem.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Artem S. Tashkinov <aros@gmx.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219570
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the DW9761 VCM controller, which is very similar to
the DW9719.
The new support is based on
drivers/external_drivers/camera/drivers/media/i2c/micam/dw9761.c
from the Xiaomi kernel sources for the Mi Pad 2.
The DW9761 support has been tested on a Xiaomi Mi Pad 2 tablet and
DW9719 support has been tested (to avoid regressions) on a Microsoft
Surface Go tablet.
Link: https://github.com/MiCode/Xiaomi_Kernel_OpenSource/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When the analog binning mode is used for high framerate operation, the
pixel rate is effectively doubled. Account for this when setting up the
pixel clock rate, and applying the vblank and exposure controls.
The previous logic only used analog binning for RAW8, but normal binning
limits the framerate on RAW10 480p [1]. So with this patch we switch to
using special binning (with 2x pixel rate) wherever possible.
[1]: https://github.com/raspberrypi/linux/issues/5493
Co-developed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Co-developed-by: Vinay Varma <varmavinaym@gmail.com>
Signed-off-by: Vinay Varma <varmavinaym@gmail.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The sensor's internal ADC supports a minimum line length of 3448 pixels,
which may be too small to use with analog binning, where ADC operates on
two lines together. Switch to a higher minimum line length of 3560
pixels to fix the blocky artefacts seen with analog binning [1].
To keep the same default framerate as before for all the modes, lower
the default fll value to compensate for the increase in llp.
[1]: https://github.com/raspberrypi/rpicam-apps/issues/281#issuecomment-1082894118
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The HBLANK control was read-only, and always configured such that the
sensor line length register was 3448. This limited the maximum exposure
time that could be achieved to around 1.26 secs.
Make HBLANK read/write so that the line time can be extended, and
thereby allow longer exposures (and slower frame rates). Retain the
overall line length setting when changing modes rather than resetting it
to a default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Commit ceddfd4493 ("media: i2c: imx219: Support four-lane operation")
added support for device tree to allow configuration of the sensor to
use 4 lanes with a link frequency of 363MHz, and amended the advertised
pixel rate to 280.8MPix/s.
However it didn't change any of the PLL settings, so actually it would
have been running overclocked in the MIPI block, and with the frame
rate and exposure calculations being wrong as the pixel rate was
unchanged.
The pixel rate and link frequency advertised were taken from the "Clock
Setting Example" section of the datasheet. However those are based on an
external clock of 12MHz, and are unachievable with a clock of 24MHz - it
seems PREPLLCLK_VT_DIV and PREPLLCK_OP_DIV can ONLY be set via the
automatic configuration documented in "9-1-2 EXCK_FREQ setting depend on
INCK frequency", not by writing the registers.
The closest we can get with a 24MHz clock is 281.6MPix/s and 364MHz.
Dropping all support for the 363MHz link frequency would cause problems
for existing users, so allow it, but log a warning that the requested
value is being changed to the supported one.
Fixes: ceddfd4493 ("media: i2c: imx219: Support four-lane operation")
Cc: stable@vger.kernel.org
Co-developed-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The link frequencies are equally valid in 2 or 4 lane modes, but
they change the hmax_min value for the mode as the MIPI block
has to have sufficient time to send the pixel data for each line.
Remove the association with number of lanes, and add hmax_min
configuration for both lane options.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The control of HMAX documented in the datasheet is consistent
with being in terms of a scaled INCK, being always 72MHz or
74.25MHz. It is NOT link frequency dependent, but the minimum
value for HMAX is dictated by the link frequency.
If PIXEL_RATE is defined as being 12 times the 72 or 74.25MHz,
and all values are scaled down again when writing HMAX, then
the numbers all work out regardless of INCK or link frequency.
Retain an hmax_min (set to the same value as the previous fixed
hmax register value) to set as the default value to avoid changing
the behaviour for existing users.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Support the use of the media pad for obtaining the link frequency.
Similarly, call the v4l2_get_link_freq() on the media pad, not on the
remote's control handler.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Obtain the link frequency from the sub-device's pad instead of a control
handler. This allows obtaining it using the get_mbus_config() sub-device
pad op which is the only method supported by the IVSC driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Memset the config argument to get_mbus_config V4L2 sub-device pad
operation to zero before calling the operation. This ensures the callers
don't need to bother with it nor the implementations need to set all
fields that may not be relevant to them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
v4l2_get_link_freq() accepts a V4L2 control handler for now, but it needs
to take struct media_pad argument in order to obtain the link frequency
using get_mbus_config() pad op. Prepare for this by allowing struct
media_pad as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Idle the device only after the async sub-device has been successfully
registered. In error handling, set the device's runtime PM status to
suspended only if it has been set to active previously in probe.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 8a89dc62f2 ("media: add imx319 camera sensor driver")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Set the device's runtime PM status and enable runtime PM before
registering the async sub-device. This is needed to avoid the case where
the device is runtime PM resumed while runtime PM has not been enabled
yet.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Cc: stable@vger.kernel.org # for >= v6.6
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Set the device's runtime PM status to suspended in probe error paths where
it was previously set to active.
Fixes: 9447082ae6 ("[media] smiapp: Implement power-on and power-off sequences without runtime PM")
Cc: stable@vger.kernel.org # for >= v5.15
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Set the device's runtime PM status to suspended in device removal only if
it wasn't suspended already.
Fixes: 9447082ae6 ("[media] smiapp: Implement power-on and power-off sequences without runtime PM")
Cc: stable@vger.kernel.org # for >= v5.15
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Introduce two variable has_csi and has_mclk within the
match data of the driver in order to know, depending on
the compatible if CSI-2 interface is available and if
the mclk clk should be retrieved.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Correct several missing unsigned type missing for loop variables
and also remove useless initialization of variables.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The endpoint is already retrieved at the beginning of the function
stm32_csi_parse_dt hence keep the endpoint pointer until the end
instead of getting a new one.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Within stm32_csi_start, use ARRAY_SIZE loop in order to search
for the right setting.
Avoid useless init of lanes_ie / lanes_en.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Call v4l2_async_register_subdev only whenever all initialization
are completed at the end of the probe function.
Remove as well useless err_free_priv label by returning directly
upon error.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Within the stm32_csi_start function, pm_runtime_put should
be called upon error following pm_runtime_get_sync.
Rework the function error handling by putting a label in
order to have common error handling for all calls requiring
pm_runtime_put.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Clarify the description of the stm32 CSI by mentioning CSI-2 and D-PHY.
Remove the bus-type property from the example since this CSI has a D-PHY,
which is the only bus-type option, making this property redundant.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The ret variable used within the function dcmipp_graph_notify_bound is
wrongly defined as unsigned int while it can also be signed.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Small cleanups for the driver, namely removal of OV2740_NUM_SUPPLIES
macro, use of unsigned int for a loop and printing the missing "0x" for a
hexadecimal number.
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The driver defines IMX214_DEFAULT_LINK_FREQ 480000000, and then
IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10),
which works out as 384MPix/s. (The 8 is 4 lanes and DDR.)
Parsing the PLL registers with the defined 24MHz input. We're in single
PLL mode, so MIPI frequency is directly linked to pixel rate. VTCK ends
up being 1200MHz, and VTPXCK and OPPXCK both are 120MHz. Section 5.3
"Frame rate calculation formula" says "Pixel rate
[pixels/s] = VTPXCK [MHz] * 4", so 120 * 4 = 480MPix/s, which basically
agrees with my number above.
3.1.4. MIPI global timing setting says "Output bitrate = OPPXCK * reg
0x113[7:0]", so 120MHz * 10, or 1200Mbit/s. That would be a link
frequency of 600MHz due to DDR.
That also matches to 480MPix/s * 10bpp / 4 lanes / 2 for DDR.
Keep the previous link frequency for backward compatibility.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The imx214 sensor supports analogue gain up to 8x and digital gain up to
16x. Implement the corresponding controls in the driver. Default gain
values are not modified by this patch.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add vblank control to allow changing the framerate /
higher exposure values.
The vblank and hblank controls are needed for libcamera support.
While at it, fix the minimal exposure time according to the datasheet.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The imx214 camera is capable of either two-lane or four-lane operation.
Currently only the four-lane mode is supported, as proper pixel rates
and link frequences for the two-lane mode are unknown.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The IMX214_REG_EXPOSURE is configured twice, once with a hardcoded value
in the mode_<res> registers arrays, and once via v4l2_ctrl_ops. The
latter is enough, drop the former.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Use the new common CCI register access helpers to replace the private
register access helpers in the imx214 driver. This simplifies the driver
by reducing the amount of code.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
