HW can have different input/output delays for each of the pins.
Currently, only E82X adapters have delay compensation based on TSPLL
config and E810 adapters have constant 1 ms compensation, both cases
only for output delays and the same one for all pins.
E825 adapters have different delays for SDP and other pins. Those
delays are also based on direction and input delays are different than
output ones. This is the main reason for moving delays to pin
description structure.
Add a field in ice_ptp_pin_desc structure to reflect that. Delay values
are based on approximate calculations of HW delays based on HW spec.
Implement external timestamp (input) delay compensation.
Remove existing definitions and wrappers for periodic output propagation
delays.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Programming the PHY registers in preparation for an increment value change
or a timer adjustment on E810 requires issuing Admin Queue commands for
each PHY register. It has been found that the firmware Admin Queue
processing occasionally has delays of tens or rarely up to hundreds of
milliseconds. This delay cascades to failures in the PTP applications which
depend on these updates being low latency.
Consider a standard PTP profile with a sync rate of 16 times per second.
This means there is ~62 milliseconds between sync messages. A complete
cycle of the PTP algorithm
1) Sync message (with Tx timestamp) from source
2) Follow-up message from source
3) Delay request (with Tx timestamp) from sink
4) Delay response (with Rx timestamp of request) from source
5) measure instantaneous clock offset
6) request time adjustment via CLOCK_ADJTIME systemcall
The Tx timestamps have a default maximum timeout of 10 milliseconds. If we
assume that the maximum possible time is used, this leaves us with ~42
milliseconds of processing time for a complete cycle.
The CLOCK_ADJTIME system call is synchronous and will block until the
driver completes its timer adjustment or frequency change.
If the writes to prepare the PHY timers get hit by a latency spike of 50
milliseconds, then the PTP application will be delayed past the point where
the next cycle should start. Packets from the next cycle may have already
arrived and are waiting on the socket.
In particular, LinuxPTP ptp4l may start complaining about missing an
announce message from the source, triggering a fault. In addition, the
clockcheck logic it uses may trigger. This clockcheck failure occurs
because the timestamp captured by hardware is compared against a reading of
CLOCK_MONOTONIC. It is assumed that the time when the Rx timestamp is
captured and the read from CLOCK_MONOTONIC are relatively close together.
This is not the case if there is a significant delay to processing the Rx
packet.
Newer firmware supports programming the PHY registers over a low latency
interface which bypasses the Admin Queue. Instead, software writes to the
REG_LL_PROXY_L and REG_LL_PROXY_H registers. Firmware reads these registers
and then programs the PHY timers.
Implement functions to use this interface when available to program the PHY
timers instead of using the Admin Queue. This avoids the Admin Queue
latency and ensures that adjustments happen within acceptable latency
bounds.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Newer firmware for the E810 devices support a 'low latency' interface to
interact with the PHY without using the Admin Queue. This is interacted
with via the REG_LL_PROXY_L and REG_LL_PROXY_H registers.
Currently, this interface is only used for Tx timestamps. There are two
different mechanisms, including one which uses an interrupt for firmware to
signal completion. However, these two methods are mutually exclusive, so no
synchronization between them was necessary.
This low latency interface is being extended in future firmware to support
also programming the PHY timers. Use of the interface for PHY timers will
need synchronization to ensure there is no overlap with a Tx timestamp.
The interrupt-based response complicates the locking somewhat. We can't use
a simple spinlock. This would require being acquired in
ice_ptp_req_tx_single_tstamp, and released in
ice_ptp_complete_tx_single_tstamp. The ice_ptp_req_tx_single_tstamp
function is called from the threaded IRQ, and the
ice_ptp_complete_tx_single_stamp is called from the low latency IRQ, so we
would need to acquire the lock with IRQs disabled.
To handle this, we'll use a wait queue along with
wait_event_interruptible_locked_irq in the update flows which don't use the
interrupt.
The interrupt flow will acquire the wait queue lock, set the
ATQBAL_FLAGS_INTR_IN_PROGRESS, and then initiate the firmware low latency
request, and unlock the wait queue lock.
Upon receipt of the low latency interrupt, the lock will be acquired, the
ATQBAL_FLAGS_INTR_IN_PROGRESS bit will be cleared, and the firmware
response will be captured, and wake_up_locked() will be called on the wait
queue.
The other flows will use wait_event_interruptible_locked_irq() to wait
until the ATQBAL_FLAGS_INTR_IN_PROGRESS is clear. This function checks the
condition under lock, but does not hold the lock while waiting. On return,
the lock is held, and a return of zero indicates we hold the lock and the
in-progress flag is not set.
This will ensure that threads which need to use the low latency interface
will sleep until they can acquire the lock without any pending low latency
interrupt flow interfering.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The TS_LL_READ macros are used as part of the low latency Tx timestamp
interface. A future firmware extension will add support for performing PHY
timer updates over this interface. Using TS_LL_READ as the prefix for these
macros will be confusing once the interface is used for other purposes.
Rename the macros, using the prefix REG_LL_PROXY_H, to better clarify that
this is for the low latency interface.
Additionally add macros for PF_SB_ATQBAH and PF_SB_ATQBAL registers to
better clarify content of this registers as PF_SB_ATQBAH contain low
part of Tx timestamp
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_read_phy_tstamp_ll_e810 function repeatedly reads the PF_SB_ATQBAL
register until the TS_LL_READ_TS bit is cleared. This is a perfect
candidate for using rd32_poll_timeout. However, the default implementation
uses a sleep-based wait. Use read_poll_timeout_atomic macro which is based
on the non-sleeping implementation and use it to replace the loop reading
in the ice_read_phy_tstamp_ll_e810 function.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware generates events for global events or port specific events.
Driver shall subscribe for health status events from firmware on supported
FW versions >= 1.7.6.
Driver shall expose those under specific health reporter, two new
reporters are introduced:
- FW health reporter shall represent global events (problems with the
image, recovery mode);
- Port health reporter shall represent port-specific events (module
failure).
Firmware only reports problems when those are detected, it does not store
active fault list.
Driver will hold only last global and last port-specific event.
Driver will report all events via devlink health report,
so in case of multiple events of the same source they can be reviewed
using devlink autodump feature.
$ devlink health
pci/0000:b1:00.3:
reporter fw
state healthy error 0 recover 0 auto_dump true
reporter port
state error error 1 recover 0 last_dump_date 2024-03-17
last_dump_time 09:29:29 auto_dump true
$ devlink health diagnose pci/0000:b1:00.3 reporter port
Syndrome: 262
Description: Module is not present.
Possible Solution: Check that the module is inserted correctly.
Port Number: 0
Tested on Intel Corporation Ethernet Controller E810-C for SFP
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Sharon Haroni <sharon.haroni@intel.com>
Signed-off-by: Sharon Haroni <sharon.haroni@intel.com>
Co-developed-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Konrad Knitter <konrad.knitter@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The new recipe should be added even if exactly the same recipe already
exists with different priority.
Example use case is when the rule is being added from TC tool context.
It should has the highest priority, but if the recipe already exists
the rule will inherit it priority. It can lead to the situation when
the rule added from TC tool has lower priority than expected.
The solution is to check the recipe priority when trying to find
existing one.
Previous recipe is still useful. Example:
RID 8 -> priority 4
RID 10 -> priority 7
The difference is only in priority rest is let's say eth + mac +
direction.
Adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
After that IP + MAC_B + RX on RID 10 (from TC tool), forward to PF0
Both will work.
In case of adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
ARP + MAC_A + RX on RID 10, forward to PF0.
Only second one will match, but this is expected.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Split ice_init_hw() call out from ice_init_dev(). Such move enables
pulling the former to be even earlier on call path, what would enable
moving ice_adapter init to be between the two (in subsequent commit).
Such move enables ice_adapter to know about number of PFs.
Do the same for ice_deinit_hw(), so the init and deinit calls could
be easily mirrored.
Next commit will rename unrelated goto labels to unroll prefix.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Kory Maincent says:
====================
Arrange PSE core and update TPS23881 driver
This patch includes several improvements to the PSE core for better
implementation and maintainability:
- Move the conversion between current limit and power limit from the driver
to the PSE core.
- Update power and current limit checks.
- Split the ethtool_get_status callback into multiple callbacks.
- Fix PSE PI of_node detection.
- Clean ethtool header of PSE structures.
Additionally, the TPS23881 driver has been updated to support power
limit and measurement features, aligning with the new PSE core
functionalities.
This patch series is the first part of the budget evaluation strategy
support patch series sent earlier:
https://lore.kernel.org/netdev/20250104161622.7b82dfdf@kmaincent-XPS-13-7390/T/#t
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
====================
Link: https://patch.msgid.link/20250110-b4-feature_poe_arrange-v3-0-142279aedb94@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PI of_node was not assigned in the regulator_config structure, leading
to failures in resolving the correct supply when different power supplies
are assigned to multiple PIs of a PSE controller. This fix ensures that the
of_node is properly set in the regulator_config, allowing accurate supply
resolution for each PI.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Expand PSE callbacks to support the newly introduced
pi_get/set_pw_limit() and pi_get_voltage() functions. These callbacks
allow for power limit configuration in the TPS23881 controller.
Additionally, the patch includes the pi_get_pw_class() the
pi_get_actual_pw(), and the pi_get_pw_limit_ranges') callbacks providing
more comprehensive PoE status reporting.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The is_enabled callback is now redundant as the admin_state can be obtained
directly from the driver and provides the same information.
To simplify functionality, the core will handle this internally, making
the is_enabled callback unnecessary at the driver level. Remove the
callback from all drivers.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ethtool_get_status callback currently handles all status and PSE
information within a single function. This approach has two key
drawbacks:
1. If the core requires some information for purposes other than
ethtool_get_status, redundant code will be needed to fetch the same
data from the driver (like is_enabled).
2. Drivers currently have access to all information passed to ethtool.
New variables will soon be added to ethtool status, such as PSE ID,
power domain IDs, and budget evaluation strategies, which are meant
to be managed solely by the core. Drivers should not have the ability
to modify these variables.
To resolve these issues, ethtool_get_status has been split into multiple
callbacks, with each handling a specific piece of information required
by ethtool or the core.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The regulator framework uses current limits, but the PSE standard and
known PSE controllers rely on power limits. Instead of converting
current to power within each driver, perform the conversion in the PSE
core. This avoids redundancy in driver implementation and aligns better
with the standard, simplifying driver development.
Remove at the same time the _pse_ethtool_get_status() function which is
not needed anymore.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When setting the PWOFF register, the controller resets multiple
configuration registers. This patch ensures these registers are
reconfigured as needed following a disable operation.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This driver frequently follows a pattern where two registers are read or
written in a single operation, followed by calculating the bit offset for
a specific channel.
Introduce helpers to streamline this process and reduce code redundancy,
making the codebase cleaner and more maintainable.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cleaned up several functions in tps23881 by removing redundant checks on
return values at the end of functions. These check has been removed, and
the return statement now directly returns the function result, reducing
the code's complexity and making it more concise.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kyle Swenson <kyle.swenson@est.tech>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Checking only the current limit is not sufficient. According to the
standard, voltage can reach up to 57V and current up to 1.92A, which
exceeds the power limit described in the standard (99.9W). Add a power
limit check to prevent this.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Setting the max_uA constraint in the regulator API imposes a current
limit during the regulator registration process. This behavior conflicts
with preserving the maximum PI power budget configuration across reboots.
Instead, compare the desired current limit to MAX_PI_CURRENT in the
pse_pi_set_current_limit() function to ensure proper handling of the
power budget.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add multicast filtering support for VLAN interfaces in HSR offload mode
for ICSSG driver.
The driver calls vlan_for_each() API on the hsr device's ndev to get the
list of available vlans for the hsr device. The driver then sync mc addr of
vlan interface with a locally mainatined list emac->vlan_mcast_list[vid]
using __hw_addr_sync_multiple() API.
The driver then calls the sync / unsync callbacks.
In the sync / unsync call back, driver checks if the vdev's real dev is
hsr device or not. If the real dev is hsr device, driver gets the per
port device using hsr_get_port_ndev() and then driver passes appropriate
vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Create an API to get the net_device to the slave port of HSR device. The
API will take hsr net_device and enum hsr_port_type for which we want the
net_device as arguments.
This API can be used by client drivers who support HSR and want to get
the net_devcie of slave ports from the hsr device. Export this API for
the same.
This API needs the enum hsr_port_type to be accessible by the drivers using
hsr. Move the enum hsr_port_type from net/hsr/hsr_main.h to
include/linux/if_hsr.h for the same.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add multicast filtering support for VLAN interfaces in dual EMAC mode
for ICSSG driver.
The driver uses vlan_for_each() API to get the list of available
vlans. The driver then sync mc addr of vlan interface with a locally
mainatined list emac->vlan_mcast_list[vid] using __hw_addr_sync_multiple()
API.
__hw_addr_sync_multiple() is used instead of __hw_addr_sync() to sync
vdev->mc with local list because the sync_cnt for addresses in vdev->mc
will already be set by the vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c]
and __hw_addr_sync() only syncs when the sync_cnt == 0. Whereas
__hw_addr_sync_multiple() can sync addresses even if sync_cnt is not 0.
Export __hw_addr_sync_multiple() so that driver can use it.
Once the local list is synced, driver calls __hw_addr_sync_dev() with
the local list, vdev, sync and unsync callbacks.
__hw_addr_sync_dev() is used with the local maintained list as the list
to synchronize instead of using __dev_mc_sync() on vdev because
__dev_mc_sync() on vdev will call __hw_addr_sync_dev() on vdev->mc and
sync_cnt for addresses in vdev->mc will already be set by the
vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c] and __hw_addr_sync_dev()
only syncs if the sync_cnt of addresses in the list (vdev->mc in this case)
is 0. Whereas __hw_addr_sync_dev() on local list will work fine as the
sync_cnt for addresses in the local list will still be 0.
Based on change in addresses in the local list, sync / unsync callbacks
are invoked. In the sync / unsync API in driver, based on whether the ndev
is vlan or not, driver passes appropriate vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a small batch of Netfilter/IPVS updates
for net-next:
1) Remove unused genmask parameter in nf_tables_addchain()
2) Speed up reads from /proc/net/ip_vs_conn, from Florian Westphal.
3) Skip empty buckets in hashlimit to avoid atomic operations that results
in false positive reports by syzbot with lockdep enabled, patch from
Eric Dumazet.
4) Add conntrack event timestamps available via ctnetlink,
from Florian Westphal.
netfilter pull request 25-01-11
* tag 'nf-next-25-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: add conntrack event timestamp
netfilter: xt_hashlimit: htable_selective_cleanup() optimization
ipvs: speed up reads from ip_vs_conn proc file
netfilter: nf_tables: remove the genmask parameter
====================
Link: https://patch.msgid.link/20250111230800.67349-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Oleksij Rempel says:
====================
Introduce unified and structured PHY
This patch set introduces a unified and well-structured interface for
reporting PHY statistics. Instead of relying on arbitrary strings in PHY
drivers, this interface provides a consistent and structured way to
expose PHY statistics to userspace via ethtool.
The initial groundwork for this effort was laid by Jakub Kicinski, who
contributed patches to plumb PHY statistics to drivers and added support
for structured statistics in ethtool. Building on Jakub's work, I tested
the implementation with several PHYs, addressed a few issues, and added
support for statistics in two specific PHY drivers.
Most of changes are tracked in separate patches.
changes v6:
- drop ethtool_stat_add patch
changes v5:
- rebase against latest net-next
====================
Link: https://patch.msgid.link/20250110060517.711683-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for reporting PHY statistics in the DP83TG720 driver. This
includes cumulative tracking of link loss events, transmit/receive
packet counts, and error counts. Implemented functions to update and
provide statistics via ethtool, with optional polling support enabled
through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for reporting PHY statistics in the DP83TD510 driver. This
includes cumulative tracking of transmit/receive packet counts, and
error counts. Implemented functions to update and provide statistics via
ethtool, with optional polling support enabled through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add an optional polling interface for PHY statistics to simplify driver
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace generic instructions for monitoring error counters with a
procedure using the unified PHY statistics interface (`--all-groups`).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce a new way to report PHY statistics in a structured and
standardized format using the netlink API. This new method does not
replace the old driver-specific stats, which can still be accessed with
`ethtool -S <eth name>`. The structured stats are available with
`ethtool -S <eth name> --all-groups`.
This new method makes it easier to diagnose problems by organizing stats
in a consistent and documented way.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce support for standardized PHY statistics reporting in ethtool
by extending the PHYLIB framework. Add the functions
phy_ethtool_get_phy_stats() and phy_ethtool_get_link_ext_stats() to
provide a consistent interface for retrieving PHY-level and
link-specific statistics. These functions are used within the ethtool
implementation to avoid direct access to the phy_device structure
outside of the PHYLIB framework.
A new structure, ethtool_phy_stats, is introduced to standardize PHY
statistics such as packet counts, byte counts, and error counters.
Drivers are updated to include callbacks for retrieving PHY and
link-specific statistics, ensuring values are explicitly set only for
supported fields, initialized with ETHTOOL_STAT_NOT_SET to avoid
ambiguity.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Adapt linkstate_get_sqi() and linkstate_get_sqi_max() to take a
phy_device argument directly, enabling support for setups with
multiple PHYs. The previous assumption of a single PHY attached to
a net_device no longer holds.
Use ethnl_req_get_phydev() to identify the appropriate PHY device
for the operation. Update linkstate_prepare_data() and related
logic to accommodate this change, ensuring compatibility with
multi-PHY configurations.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev_deactivate_many() role is to remove the qdiscs
of a network device.
When/if a qdisc is dismantled, an rcu grace period
is needed to make sure all outstanding qdisc enqueue
are done before we proceed with a qdisc reset.
Most virtual devices do not have a qdisc.
We can call the expensive synchronize_net() only
if needed.
Note that dev_deactivate_many() does not have to deal
with qdisc-less dev_queue_xmit, as an old comment
was claiming.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250109171850.2871194-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tariq Toukan says:
====================
mlx5 HW-Managed Flow Steering in FS core level
This patchset by Moshe follows Yevgeny's patchsets [1][2] on subject
"HW-Managed Flow Steering in mlx5 driver". As introduced there in HW
managed Flow Steering mode (HWS) the driver is configuring steering
rules directly to the HW using WQs with a special new type of WQE (Work
Queue Element). This way we can reach higher rule insertion/deletion
rate with much lower CPU utilization compared to SW Managed Flow
Steering (SWS).
This patchset adds API to manage namespace, flow tables, flow groups and
prepare FTE (Flow Table Entry) rules. It also adds caching and pool
mechanisms for HWS actions to allow sharing of steering actions among
different rules. The implementation of this API in FS layer, allows FS
core to use HW Managed Flow Steering in addition to the existing FW or
SW Managed Flow Steering.
Patch 13 of this series adds support for configuring HW Managed Flow
Steering mode through devlink param, similar to configuring SW Managed
Flow Steering mode:
# devlink dev param set pci/0000:08:00.0 name flow_steering_mode \
cmode runtime value hmfs
In addition, the series contains 2 HWS patches from Yevgeny that
implement flow update support.
[1] https://lore.kernel.org/netdev/20240903031948.78006-1-saeed@kernel.org/
[2] https://lore.kernel.org/all/20250102181415.1477316-1-tariqt@nvidia.com/
====================
Link: https://patch.msgid.link/20250109160546.1733647-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is the second part of update flow implementation.
Instead of using two action RTCs, we use the same RTC which is twice
the size of what was required before the update flow support.
This way we always allocate STEs from the same RTC (same pool),
which means that update is done similar to how create is done.
The bigger size allows us to allocate and write new STEs, and
later free the old (pre-update) STEs.
Similar to rule creation, STEs are written in reverse order:
- write action STEs, while match STE is still pointing to
the old action STEs
- overwrite the match STE with the new one, which now
is pointing to the new action STEs
Old action STEs can be freed only once we got completion on the
writing of the new match STE. To implement this we added new rule
states: UPDATING/UPDATED. Rule is moved to UPDATING state in the
beginning of the update flow. Once all completions are received,
rule is moved to UPDATED state. At this point old action STEs are
freed and rule goes back to CREATED state.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109160546.1733647-16-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is the first part of update flow implementation.
Update flow should support rules with single STE (match STE only),
as well as rules with multiple STEs (match STE plus action STEs).
Supporting the rules with single STE is straightforward: we just
overwrite the STE, which is an atomic operation.
Supporting the rules with action STEs is a more complicated case.
The existing implementation uses two action RTCs per matcher and
alternates between the two for each update request.
This implementation was unnecessarily complex and lead to some
unhandled edge cases, so the support for rule update with multiple
STEs wasn't really functional.
This patch removes this code, and the next patch adds implementation
of a different approach.
Note that after applying this patch and before applying the next
patch we still have support for update rule with single STE (only
match STE w/o action STEs), but update will fail for rules with
action STEs.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109160546.1733647-15-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
