The driver strength is too high for SDR104 mode. Change the driver strength
to x3 according to hardware recommendation.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB3 PHY tuning properties for imx95-15x15-evk and imx95-19x19-evk
boards according to signal measurement results.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 tpm3 netc_timer and related phys
regulators pinmux and related child nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Variscite has updated the Ethernet PHY on the VAR-SOM-MX93 from the
ADIN1300BCPZ to the MaxLinear MXL86110, as documented in the
August 2023 revision changelog.
Link: https://variwiki.com/index.php?title=VAR-SOM-MX93_rev_changelog
Update the device tree accordingly:
- Drop the regulator node used to power the previously PHY.
- Add support for the reset line using GPIO1_IO07 with proper timings.
- Configure the PHY LEDs via the LED subsystem under /sys/class/leds/,
leveraging the support implemented in the mxl86110 PHY driver
(drivers/net/phy/mxl-86110.c).
Two LEDs are defined to match the LED configuration on the Variscite
VAR-SOM Carrier Boards:
* LED@0: Yellow, netdev trigger.
* LED@1: Green, netdev trigger.
- Adjust the RGMII clock pad control settings to match the updated PHY
requirements.
These changes ensure proper PHY initialization and LED status indication
for the new MaxLinear MXL86110, improving board compatibility with the
latest hardware revision.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW74xx D revision has added a M2SKT_WDIS2# GPIO which routes to the
W_DISABLE2# pin of the M.2 socket. Update the gpio name for consistency.
Fixes: 6a5d95b06d ("arm64: dts: imx8mp-venice-gw74xx: add M2SKT_GPIO10 gpio configuration")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move configuration for ADC voltage reference from board DTS to a SoM
include file. The SoC ADC reference voltage is connected to a "VDDA_1V8"
voltage node and supplied by the PMIC's BUCK5 regulator. The reference
voltage is thus defined by the SoM and cannot be changed by the carrier
board design and as such belongs into the SoM include file.
Moreover, with this in place, customers designing own carrier boards can
simply include imx93-phycore-som.dtsi and enable adc1 in their own DTS
without the need to define dummy ADC vref regulator themselves anymore.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone and convert
the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set ethernet1 alias to EQOS interface on phyBOARD-Segin-i.MX93 marking
it the secondary networking interface. The primary ethernet0 interface
is already set by the SoM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move alias for ethernet0 interface to the phyCORE-i.MX93 SoM include
file. The reason behind it is that the physical location of the PHY chip
connected to FEC interface is on the SoM itself and alias thus belongs
into the SoM device-tree. Consequently, it can be used by all boards
based on the phyCORE-i.MX93 SoM (phyBOARD-Segin and phyBOARD-Nash).
This also enables us to mark FEC interface as the primary / first for
networking in the bootloader and systemd (predictable interface names).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the BOE av123z7m-n17 variant of the Moduline Display, this variant
comes with a 12.3" 1920x720 display.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the BOE av101hdt-a10 variant of the Moduline Display, this variant
comes with a 10.1 1280x720 display with a touchscreen (not working in
mainline).
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Moduline Display platform is a part of the wider GOcontroll Moduline
ecosystem. These are embedded controllers that focus on modularity with
their swappable IO modules.
The base Moduline Display board includes a board-to-board connector with
various busses to enable adding new display types required by the
application. It includes 2 Moduline IO module slots, a simple mono
codec/amplifier, a four channel adc, 2 CAN busses, an RTC and optional
wifi/bluetooth.
busses to the display adapter include:
- 4 lane LVDS
- 4 lane MIPI-DSI
- 4 lane MIPI-CSI
- HDMI 2.0a
- USB 2.0
- I2S
- I2C
- SPI
Also a couple of GPIO and PWM pins for controlling various ICs on the
display adapter board.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ka-Ro Electronics tx8p-ml81 is a COM based on the imx8mp SOC. It has
2 GB of ram and 8 GB of eMMC storage on board.
Add it to enable boards based on this Module
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently to configure each IOMUXC_SW_PAD_CTL_PAD the raw value of this
register is written in the dts, these values are not obvious. Add defines
which describe the fields of this register which can be or-ed together to
produce readable settings.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit da5dd31efd ("gpio: vf610: Switch to gpio-mmio"),
the vf610 GPIO driver no longer uses the static number 32 for
gc->ngpio. This allows users to configure the number of GPIOs
per port.
And some gpio controllers did have less pads. So add 'ngpios' here,
this can save some memory when request bitmap, and also show user
more accurate information when use gpio tools.
Besides, some gpio controllers have hole in the gpio ranges, so use
'gpio-reserved-ranges' to cover that, then the gpioinfo tool show the
correct result.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Starting with commit e6ef4f8ede ("gpio: vf610: make irq_chip immutable")
gpio-vf610 supports locking GPIO being used for IRQ. This already prevents
configuring the GPIO as output, so there is no need for a GPIO hog.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa9352 is only using LPDDR4X, so the BUCK2 regulator should be fixed
at 600MV.
Fixes: d2858e6bd3 ("arm64: dts: freescale: imx93-tqma9352: Add PMIC node")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hook up the gpu as a passive cooling device to the thermal zones' alert
trip point just like the cpu.
The gpu here consists of 3D GPU, 2D GPU and NPU.
One way to test would be to set one "alert" trip point low enough
and watch the cooling device state increase:
echo 10000 > /sys/class/thermal/thermal_zone0/trip_point_0_temp
watch cat /sys/class/thermal/cooling_device*/cur_state
And of course set the trip point back to its original value and watch
the cooling device states jump to 0 again.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I.MX95 I3C only need two clocks so add clock fix. Add "nxp,imx95-i3c"
compatible string for all imx95 i3c nodes.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Pull timer fix from Thomas Gleixner:
"Add the missing seq_file forward declaration in the timer namespace
header"
* tag 'timers-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timens: Add struct seq_file forward declaration
Add initial DMR support, which required smarter RAPL probe
Fix AMD MSR RAPL energy reporting
Add RAPL power limit configuration output
Minor fixes
Signed-off-by: Len Brown <len.brown@intel.com>
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Increase the code readability by moving the no_perf/no_msr flag and the
cai->perf_name/cai->msr sanity checks into the counter probe functions.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_msr_perf_counter_(), add_msr_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_msr_perf_counter_() and move all the logic to
add_msr_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_rapl_perf_counter_(), add_rapl_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_rapl_perf_counter_() and move all the logic to
add_rapl_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Quit early for unsupported RAPL counters.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
rapl_joules bit should always be checked even if
platform_features->rapl_msrs is not set or no_msr flag is used.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 05a2f07db8 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db8 ("tools/power turbostat: read RAPL counters via perf")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
