Use gpiod_set_value_cansleep() instead of gpiod_set_value()
to fix the below call trace in the boot log:
[ 5.690534] Call trace:
[ 5.690536] gpiod_set_value+0x40/0xa4
[ 5.690540] anx7625_runtime_pm_resume+0xa0/0x324 [anx7625]
[ 5.690545] __rpm_callback+0x48/0x1d8
[ 5.690549] rpm_callback+0x6c/0x78
Certain GPIO controllers require access via message-based buses
such as I2C or SPI, which may cause the GPIOs to enter a sleep
state. Therefore, use the gpiod_set_value_cansleep().
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250505094245.2660750-7-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
In the anx7625_sink_detect(), the device is checked to see
if it is a panel bridge, and it always sends a "connected"
status to the connector. When adding the DP port on port 1 of the
anx7625, it incorrectly treats it as a panel bridge and sends an
always "connected" status. Instead of checking the status on the
panel bridge, it's better to check the hpd_status for connectors
that supports hot-plugging. This way, it verifies the hpd_status
variable before sending the status to the connector.
In case of eDP, anx7625_bridge_detect() will not get called because
the bridge->ops condition in anx7625_link_bridge() will not be
satisfied. Since anx7625_sink_detect() is called from
anx7625_bridge_detect(), this results in the sink_detect logic not
being executed for eDP.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505094245.2660750-6-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The anx7625_link_bridge() checks if a device is not a panel
bridge and add DRM_BRIDGE_OP_HPD and DRM_BRIDGE_OP_DETECT
flags to the drm_bridge->ops. However, on port 1 of the anx7625
bridge, any device added is always treated as a panel bridge,
preventing connector_detect() from being called. To resolve
this, instead of just checking if it is a panel bridge, verify
the type of device based on aux whether it is a DisplayPort or
eDP panel. If the device is not of the eDP type, add
DRM_BRIDGE_OP_HPD and DRM_BRIDGE_OP_DETECT flags to the to
the drm_bridge->ops.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505094245.2660750-5-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The HSYNC/VSYNC polarity of rk3036 HDMI are controlled by GRF.
Without the polarity configuration in GRF, it can be observed
from the HDMI protocol analyzer that the H/V front/back timing
output by RK3036 HDMI are currently not in line with the specifications.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250422070455.432666-5-andyshrk@163.com
DRM_DISPLAY_DP_AUX_BUS cannot be selected when CONFIG_OF is disabled:
WARNING: unmet direct dependencies detected for DRM_DISPLAY_DP_AUX_BUS
Depends on [n]: HAS_IOMEM [=y] && DRM [=y] && OF [=n]
Selected by [y]:
- DRM_ROCKCHIP [=y] && HAS_IOMEM [=y] && DRM [=y] && ROCKCHIP_IOMMU [=y] && ROCKCHIP_ANALOGIX_DP [=y]
Rockchip platforms all depend on OF anyway, so add the dependency here
for compile testing.
Fixes: d7b4936b2b ("drm/rockchip: analogix_dp: Add support to get panel from the DP AUX bus")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250423164422.2793634-1-arnd@kernel.org
The devm_kzalloc() function returns NULL on failure, not error pointers.
Also printing an error message for kmalloc() failures is against kernel
style so just return -ENOMEM without printing a message. (Kmalloc
already prints a message).
Fixes: 4b35f0f41e ("drm/st7571-i2c: add support for Sitronix ST7571 LCD controller")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/aBHZYgPPPYY-J8Vd@stanley.mountain
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
The generic FourCC format always prints the data using the big endian
order. It is generic because it allows to read the data using a custom
ordering.
The current code uses "n" for reading data in the reverse host ordering.
It makes the 4 variants [hnbl] consistent with the generic printing
of IPv4 addresses.
Unfortunately, it creates confusion on big endian systems. For example,
it shows the data &(u32)0x67503030 as
%p4cn 00Pg (0x30305067)
But people expect that the ordering stays the same. The network ordering
is a big-endian ordering.
The problem is that the semantic is not the same. The modifiers affect
the output ordering of IPv4 addresses while they affect the reading order
in case of FourCC code.
Avoid the confusion by replacing the "n" modifier with "hR", aka
reverse host ordering. It is inspired by the existing %p[mM]R printf
format.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/r/CAMuHMdV9tX=TG7E_CrSF=2PY206tXf+_yYRuacG48EWEtJLo-Q@mail.gmail.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Aditya Garg <gargaditya08@live.com>
Link: https://lore.kernel.org/r/20250428123132.578771-1-pmladek@suse.com
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
The newly added driver calls drm_client_setup(), but that is not
always built in:
x86_64-linux-ld: vmlinux.o: in function `st7571_probe':
st7571-i2c.c:(.text+0x7b7119): undefined reference to `drm_client_setup'
Select the appropriate Kconfig symbol.
Fixes: 4b35f0f41e ("drm/st7571-i2c: add support for Sitronix ST7571 LCD controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20250428150752.3970145-1-arnd@kernel.org
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
This is the new API for allocating DRM bridges.
These two drivers are tangled together by the ldb_add_bridge_helper(), so
they are converted at once.
They also have a similar design, each embedding an array of channels in
their main struct, and each channel embeds a drm_bridge. This prevents
dynamic, refcount-based deallocation of the bridges.
To make the new, dynamic bridge allocation possible:
* change the array of channels into an array of channel pointers
* allocate each channel using devm_drm_bridge_alloc()
* adapt ldb_add_bridge_helper() to not set the funcs pointer
(now done by devm_drm_bridge_alloc())
* adapt the code wherever using the channels
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Liu Ying <victor.liu@nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-31-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
In the case of MMU errors caused by the TFU unit, the
client that causes the MMU error is expected to be reported.
But in the case of MMU TFU errors, a non existing client was
being reported. This happened because the client calculation
was taking into account more than the bits 0-7 from the
axi_id that were representing the client.
[ 27.845132] v3d fec00000.v3d: MMU error from client ? (13) at 0x3bb1000, pte invalid
Masking the bits and using the correct axi_id ranges fixes the
calculation to report the real guilty client on V3D 4.1 and 4.2.
Make the MMU error print axi_id with hexadecimal as used in the
ranges.
Fixes: 38c2c7917a ("drm/v3d: Fix and extend MMU error handling.")
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://lore.kernel.org/r/20250425122522.18425-1-jmcasanova@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Introduce a heartbeat-based Timeout Detection and Recovery (TDR) mechanism.
The enhancement aims to improve the reliability of device hang detection by
monitoring heartbeat updates.
Each progressing inference will update heartbeat counter allowing driver to
monitor its progression. Limit maximum number of reschedules when heartbeat
indicates progression to 30. This increases the maximum running time of
single inference to about 60 seconds.
The heartbeat mechanism provides a more robust method for detecting device
hangs, potentially reducing false positive recoveries due to long running
inferences.
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://lore.kernel.org/r/20250416102555.384526-1-maciej.falkowski@linux.intel.com
All IMG Rogue GPUs include a reset line that participates in the
power-up sequence. On some SoCs (e.g., T-Head TH1520 and Banana Pi
BPI-F3), this reset line is exposed and must be driven explicitly to
ensure proper initialization. On others, such as the currently
supported TI SoC, the reset logic is handled in hardware or firmware
without exposing the line directly. In platforms where the reset line is
externally accessible, if it is not driven correctly, the GPU may remain
in an undefined state, leading to instability or performance issues.
This commit adds a dedicated reset controller to the drm/imagination
driver. By managing the reset line (where applicable) as part of normal
GPU bring-up, the driver ensures reliable initialization across
platforms regardless of whether the reset is controlled externally or
handled internally.
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://lore.kernel.org/r/20250418-apr_18_reset_img-v6-2-85a06757b698@samsung.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
