When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab20 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab20 ("gro: Add internal interfaces for VLAN")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates says:
====================
Prevent uncaught exceptions in tdc
This patch series addresses two potential bugs in tdc that can
cause exceptions to be raised in certain circumstances. These
exceptions are generally not handled, so instead we will prevent
them from being raised.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like the existing community to be kept in the loop for any new
developments on CAKE; and I certainly plan to keep maintaining it. Reflect
this in MAINTAINERS.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
splice(2) fails with -EINVAL when called reading on a socket with no splice_read
set in its proto_ops (such as vsock sockets). Switch this to fallbacks to a
generic_file_splice_read instead.
Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Explicitly pad short ELP packets with zeros, by Sven Eckelmann
- Fix packet size calculation when merging fragments,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_idr_check_alloc() can return a negative value, on allocation failures
(-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases.
Fixes: 0190c1d452 ("net: sched: atomically check-allocate action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return 'err' in the error handling path instead of 0.
Return explicitly 0 in the normal path, instead of 'err', which is known
to be 0 at this point.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
These is no need to hold dst before calling rt6_remove_exception_rt().
The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(),
which has been removed in Commit 93531c6743 ("net/ipv6: separate
handling of FIB entries from dst based routes"). Otherwise, it will
cause a dst leak.
This patch is to simply remove the dst_hold_safe() call before calling
rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt().
It's safe, because the removal of the exception that holds its dst's
refcnt is protected by rt6_exception_lock.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Fixes: 23fb93a4d3 ("net/ipv6: Cleanup exception and cache route handling")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using 2.5G speed relies on the SerDes lanes being configured
accordingly. The lanes have to be reconfigured to switch between
1G and 2.5G, and for now only the bootloader does this configuration.
In the case we add a Comphy driver to handle switching the lanes
dynamically, it's better for now to stick with supporting only 1G and
add advertisement for 2.5G once we really are capable of handling both
speeds without problem.
Since the interface mode is initialy taken from the DT, we want to make
sure that adding comphy support won't break boards that don't update
their dtb.
Fixes: da58a931f2 ("net: mvneta: Add support for 2500Mbps SGMII")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx4 fixes for 4.20-rc
This patchset includes small fixes for mlx4_core driver.
First patch by Jack zeros a field in a FW communication
command, to match the FW spec.
Please queue it to -stable >= v3.17.
In the second patch I zero-initialize a variable to silence
a compliation warning.
Please queue it to -stable >= v3.19.
Third patch by Aya replaces int fields with unsigned int,
to fix a UBSAN warning.
Please queue it to -stable >= v3.13.
Series generated against net commit:
db8ddde766 Merge branch 'qed-Miscellaneous-bug-fixes'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161 ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the uid variable to zero to avoid the compilation warning.
Fixes: 7a89399ffa ("net/mlx4: Add mlx4_bitmap zone allocator")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c83 ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EDT conversion happened, fq lost the ability to enfore a maxrate
for all flows. It kept it for non EDT flows.
This commit restores the functionality.
Tested:
tc qd replace dev eth0 root fq maxrate 500Mbit
netperf -P0 -H host -- -O THROUGHPUT
489.75
Fixes: ab408b6dc7 ("tcp: switch tcp and sch_fq to new earliest departure time model")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The life-checking function, which is used by kAFS to make sure that a call
is still live in the event of a pending signal, only samples the received
packet serial number counter; it doesn't actually provoke a change in the
counter, rather relying on the server to happen to give us a packet in the
time window.
Fix this by adding a function to force a ping to be transmitted.
kAFS then keeps track of whether there's been a stall, and if so, uses the
new function to ping the server, resetting the timeout to allow the reply
to come back.
If there's a stall, a ping and the call is *still* stalled in the same
place after another period, then the call will be aborted.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Fixes: f4d15fb6f9 ("rxrpc: Provide functions for allowing cleaner handling of signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with CONFIG_THERMAL=m and cxgb4 as built-in build fails, and
'commit e70a57fa59 ("cxgb4: fix thermal configuration dependencies")'
tries to fix it but when cxgb4i is made built-in build fails again,
use IS_REACHABLE instead of IS_ENABLED to fix the issue.
Fixes: e70a57fa59 (cxgb4: fix thermal configuration dependencies)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
Most of the bug fixes are related to the new 57500 chips, including some
initialization and counter fixes, disabling RDMA support, and a
workaround for occasional missing interrupts. The last patch from
Vasundhara fixes the year/month parameters for firmware coredump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep track of the number of times the workaround code for 57500 A0
has been triggered. This is a per NQ counter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can sometimes not generate NQ MSIX with a single pending
CP ring entry. This seems to always happen at the last entry of
the CP ring before it wraps. Add logic to check all the CP rings for
pending entries without the CP ring consumer index advancing. Calling
HWRM_DBG_RING_INFO_GET to read the context of the CP ring will flush
out the NQ entry and MSIX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no RDMA support on 57500 chips yet, so prevent bnxt_re from
registering on these chips. There is intermittent failure if bnxt_re
is allowed to register and proceed with RDMA operations.
Fixes: 1ab968d2f1 ("bnxt_en: Add PCI ID for BCM57508 device.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software counter structure is defined in both the CP ring's structure
and the NQ ring's structure on the new devices. The legacy code adds the
counter to the CP ring's structure and the counter won't get displayed
since the ethtool code is looking at the NQ ring's structure.
Since all other counters are contained in the NQ ring's structure, it
makes more sense to count rx_l4_csum_errors in the NQ.
Fixes: 50e3ab7836 ("bnxt_en: Allocate completion ring structures for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit has added the reservation of RSS context. This requires
bnxt_hwrm_vnic_qcaps() to be called before allocating any RSS contexts.
The bnxt_hwrm_vnic_qcaps() call sets up proper flags that will
determine how many RSS contexts to allocate to support NTUPLE.
This causes a regression that too many RSS contexts are being reserved
and causing resource shortage when enabling many VFs. Fix it by calling
bnxt_hwrm_vnic_qcaps() earlier.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue happens when trying to add an existent tunnel. It
doesn't call sock_put() before returning -EEXIST to release
the sock refcnt that was held by calling sock_hold() before
the existence check.
This patch is to fix it by holding the sock after doing the
existence check.
Fixes: f6cd651b05 ("l2tp: fix race in duplicate tunnel detection")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin says:
====================
qed: Miscellaneous bug fixes
This patch series fixes several unrelated bugs across the driver.
Please consider applying to net.
V1->V2:
-------
Use dma_rmb() instead of rmb().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes: d6f94d91f7 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Pull networking fixes from David Miller:
"One last pull request before heading to Vancouver for LPC, here we have:
1) Don't forget to free VSI contexts during ice driver unload, from
Victor Raj.
2) Don't forget napi delete calls during device remove in ice driver,
from Dave Ertman.
3) Don't request VLAN tag insertion of ibmvnic device when SKB
doesn't have VLAN tags at all.
4) IPV4 frag handling code has to accomodate the situation where two
threads try to insert the same fragment into the hash table at the
same time. From Eric Dumazet.
5) Relatedly, don't flow separate on protocol ports for fragmented
frames, also from Eric Dumazet.
6) Memory leaks in qed driver, from Denis Bolotin.
7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren.
8) Validate cls_flower nested policies properly, from Jakub Kicinski.
9) Clearing of stats counters in mc88e6xxx driver doesn't retain
important bits in the G1_STATS_OP register causing the chip to
hang. Fix from Andrew Lunn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
act_mirred: clear skb->tstamp on redirect
net: dsa: mv88e6xxx: Fix clearing of stats counters
tipc: fix link re-establish failure
net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
net: mvneta: correct typo
flow_dissector: do not dissect l4 ports for fragments
net: qualcomm: rmnet: Fix incorrect assignment of real_dev
net: aquantia: allow rx checksum offload configuration
net: aquantia: invalid checksumm offload implementation
net: aquantia: fixed enable unicast on 32 macvlan
net: aquantia: fix potential IOMMU fault after driver unbind
net: aquantia: synchronized flow control between mac/phy
net: smsc95xx: Fix MTU range
net: stmmac: Fix RX packet size > 8191
qed: Fix potential memory corruption
qed: Fix SPQ entries not returned to pool in error flows
qed: Fix blocking/unlimited SPQ entries leak
qed: Fix memory/entry leak in qed_init_sp_request()
inet: frags: better deal with smp races
net: hns3: bugfix for not checking return value
...
Pull Kbuild fixes from Masahiro Yamada:
- fix build errors in binrpm-pkg and bindeb-pkg targets
- fix false positive matches in merge_config.sh
- fix build version mismatch in deb-pkg target
- fix dtbs_install handling in (bin)deb-pkg target
- revert a commit that allows setlocalversion to write to source tree
* tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: Fix inclusion of dtbs in debian package
Revert "scripts/setlocalversion: git: Make -dirty check more robust"
kbuild: deb-pkg: fix too low build version number
kconfig: merge_config: avoid false positive matches from comment lines
kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used
kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used
