This change adds debugfs to read and write temperature sensor coefficients
- g, h, j and cal5.
The coefficients can vary between product and product, so it can be very
useful to be able to modify them on the fly during the calibration
process.
e.g.:
cat /sys/kernel/debug/940f23d0000.pvt/ts_coeff_cal5
4096
echo 83000 > sys/kernel/debug/940f23d0000.pvt/ts_coeff_g
Signed-off-by: Eliav Farber <farbere@amazon.com>
Link: https://lore.kernel.org/r/20220908152449.35457-21-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add optional temperature coefficient properties:
*) moortec,ts-coeff-g
*) moortec,ts-coeff-h
*) moortec,ts-coeff-cal5
*) moortec,ts-coeff-j
If defined they shall be used instead of defaults.
The coefficients were added to device tree on top of the series property
(which can be used to select between series 5 and series 6), because
coefficients can vary between product and product, and code defaults might
not be accurate enough.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-19-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current equation used in code is aligned to series 5:
T = G + H * (n / cal5 - 0.5) + J * F
Where:
G = 60, H = 200, cal5 = 4094, J = -0.1, F = frequency clock in MHz
Series 6 has a slightly different equation:
T = G + H * (n / cal5 - 0.5)
and a different set of coefficients:
G = 57.4, H = 249.4, cal5 = 4096
This change supports equation and coefficients for both series.
(for series 6, J is set to 0).
The series is determined according to “moortec,ts-series” property in
the device tree.
If absent, series 5 is assumed to be the default.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-18-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add optional "moortec,ts-series" property to define the temperature
equation and coefficients that shall be used to convert the digital
output to value in milli-Celsius.
Supported series: 5 (default) and 6.
Series 5:
T = G + H * (n / cal5 - 0.5) + J * F
Where: G = 60, H = 200, cal5 = 4094, J = -0.1, F = frequency clock in MHz
Series 6:
T = G + H * (n / cal5 - 0.5)
Where: G = 57.4, H = 249.4, cal5 = 4096
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-17-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Modify the equation and coefficients used to convert the digital output
to temperature according to series 5 of the Moortec Embedded Temperature
Sensor (METS) datasheet:
T = G + H * (n / cal5 - 0.5) + J * F
Where:
*) G = 60, H = 200, cal5 = 4094, J = -0.1.
*) F = frequency clock in MHz.
*) n is the digital output.
In code, the G, H and J coefficients are multiplied by a factor of 1000
to get the temperature in milli-Celsius.
Final result is clamped in case it exceeds min/max thresholds.
Change is done since it is unclear where the current equation and
coefficients came from.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-16-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mr76006 pre-scaler which provides divide-by-2 scaling
of the input voltage, so that it can be presented to the VM for
measurement within its range (the VM input range is limited from -0.1V
to 1V).
The driver reads from the device-tree all the channels that use the
mr76006 pre-scaler and multiplies the voltage result by a factor of 2,
to represent to the user with the actual voltage input source.
Channels that are not in the device-tree are multiplied by a factor
of 1.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-15-farbere@amazon.com
[groeck: Addressed conflicts against commit d59eacaac9]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mr76006 pre-scaler which provides divide-by-2 scaling of
the input voltage, so that it can be presented to the VM for measurement
within its range (the VM input range is limited to -0.1V to 1V).
The new "moortec,vm-pre-scaler-x2" property lists the channels that use
the mr76006 pre-scaler.
The driver will use this list to multiply the voltage result by 2, to
present to the user with the actual voltage input source.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-14-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add active channel support per voltage monitor.
The number of active channels is read from the device-tree.
When absent in device-tree, all channels are assumed to be used.
This shall be useful to expose sysfs only for inputs that are connected
to a voltage source.
Setting number of active channels to 0, means that entire VM sensor is
not used.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-13-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Static analyzers report:
drivers/hwmon/emc2305.c:194 emc2305_set_cur_state()
warn: impossible condition '(val > 255) => (0-255 > 255)'
'val' is u8 and thus can never be larger than 255. In theory
the operation calculating 'val' could result in a value larger
than 255, but this won't happen because its parameter has already
been range checked and it is guaranteed that the result never exceeds
255. Remove the unnecessary value check.
Cc: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On systems with more than one tps23861, creating the debugfs directory
for additional devices fails with
debugfs: Directory 'tps23861' with parent '/' already present!
To resolve this, include the hwmon device name in the directory name.
Since the name is unique, this guarantees that the debugfs directory
is unique.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220907015405.16547-2-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When reading the 'port_status' debugfs entry, some I2C registers were
read more than once. This looks inefficient in an I2C trace.
To reduce I2C traffic, update tps23861_port_status_show() to only read
each register once. Indexing the port number from 0 instead of 1 also
allows simplifying things a bit.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://lore.kernel.org/r/20220907015405.16547-1-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX31790 has a tach input enable bit in each fan's configuration
register. This is only enabled by the driver if RPM mode is selected,
but the driver doesn't provide a way to independently enable tachometer
input regardless of the regulator mode.
By adding the fanN_enable sysfs files, we can decouple the tach input
from the regulator mode. Also update the documentation.
Signed-off-by: Justin Ledford <justinledford@google.com>
Link: https://lore.kernel.org/r/20220829195930.2521755-1-justinledford@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code, the error handling paths and avoid the need of
a dedicated function used with devm_add_action_or_reset().
Based on my test with allyesconfig, this reduces the .o size from:
text data bss dec hex filename
2419 1472 0 3891 f33 drivers/hwmon/sparx5-temp.o
down to:
2155 1472 0 3627 e2b drivers/hwmon/sparx5-temp.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/cfe4c965074b5ecbe03830b05e038b4594c7b970.1661336689.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When dell-smm-hwmon is loaded on a machine with a buggy BIOS
with the option "force" being enabled, it wrongly prints
that the buggy features where disabled. This may cause
users to wrongly assume that the driver still protects them
from these BIOS bugs even with "force" being enabled.
Replace the messages with two messages each which are depending
on the value of the "force" parameter. The messages which are
being printed when "force" is not set use dev_notice() instead
of dev_warn() since they only serve as a notice.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220822174053.8750-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading virtual temperature sensors for the D5 Next, Octo,
Quadro and Farbwerk 360.
Virtual temperature sensors are written to the device by the user, pulling
from an arbitrary value source. Writing to them is not yet reverse
engineered, so the only way to set them for now is to use the official
software.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220817121441.112198-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The offsets for setting speeds of fans connected to Quadro are off by one.
Set them to their correct values.
The offsets as shown point to registers for setting the fan control mode,
which will be explored in future patches, but slipped in here. When
setting fan speeds, the resulting values were overlapping, which made the
fans still run in my initial testing.
Fixes: cdbe34da01 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controller")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220914114327.6941-1-savicaleksa83@gmail.com
Cc: stable@vger.kenrel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull Kbuild fixes from Masahiro Yamada:
- Remove unused scripts/gcc-ld script
- Add zstd support to scripts/extract-ikconfig
- Check 'make headers' for UML
- Fix scripts/mksysmap to ignore local symbols
* tag 'kbuild-fixes-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
mksysmap: Fix the mismatch of 'L0' symbols in System.map
kbuild: disable header exports for UML in a straightforward way
scripts/extract-ikconfig: add zstd compression support
scripts: remove obsolete gcc-ld script
Pull arm64 fixes from Will Deacon:
"Three small arm64 fixes, all related to optional architecture
extensions: BTI, SME and 52-bit virtual addressing:
- Disable in-kernel BTI when compiling with GCC, as it makes invalid
assumptions about the distance between functions which has led to
crashes when calling modules on a CPU with BTI support
- Remove bogus TIF_SME flag management if memory allocation fails in
the ptrace code
- Fix the resume path when configured for 52-bit virtual addressing"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix resume for 52-bit enabled builds
arm64/ptrace: Don't clear calling process' TIF_SME on OOM
arm64/bti: Disable in kernel BTI when cross section thunks are broken
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes from Lu Baolu:
- Boot kdump kernels with VT-d scalable mode on
- Calculate the right page table levels
- Fix two recursive locking issues
- Fix a lockdep splat issue
- AMD IOMMU fixes:
- Fix for completion-wait command to use full 64 bits of data
- Fix PASID related issue where GPU sound devices failed to
initialize
- Fix for Virtio-IOMMU to report correct caching behavior, needed for
use with VFIO
* tag 'iommu-fixes-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix false ownership failure on AMD systems with PASID activated
iommu/vt-d: Fix possible recursive locking in intel_iommu_init()
iommu/virtio: Fix interaction with VFIO
iommu/vt-d: Fix lockdep splat due to klist iteration in atomic context
iommu/vt-d: Fix recursive lock issue in iommu_flush_dev_iotlb()
iommu/vt-d: Correctly calculate sagaw value of IOMMU
iommu/vt-d: Fix kdump kernels boot failure with scalable mode
iommu/amd: use full 64-bit value in build_completion_wait()
Pull MIPS fixes from Thomas Bogendoerfer:
- fix for loongson32 starup hang
- fix for octeon irq setup problem
- fix compiler warning for new CONFIG option
- switch to SPARSEMEM_EXTREME for all platforms selecting SPARSEMEM
* tag 'mips-fixes_6.0_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: Select SPARSEMEM_EXTREME
MIPS: OCTEON: irq: Fix octeon_irq_force_ciu_mapping()
MIPS: octeon: Get rid of preprocessor directives around RESERVE32
MIPS: loongson32: ls1c: Fix hang during startup
The AMD IOMMU driver cannot activate PASID mode on a RID without the RID's
translation being set to IDENTITY. Further it requires changing the RID's
page table layout from the normal v1 IOMMU_DOMAIN_IDENTITY layout to a
different v2 layout.
It does this by creating a new iommu_domain, configuring that domain for
v2 identity operation and then attaching it to the group, from within the
driver. This logic assumes the group is already set to the IDENTITY domain
and is being used by the DMA API.
However, since the ownership logic is based on the group's domain pointer
equaling the default domain to detect DMA API ownership, this causes it to
look like the group is not attached to the DMA API any more. This blocks
attaching drivers to any other devices in the group.
In a real system this manifests itself as the HD-audio devices on some AMD
platforms losing their device drivers.
Work around this unique behavior of the AMD driver by checking for
equality of IDENTITY domains based on their type, not their pointer
value. This allows the AMD driver to have two IDENTITY domains for
internal purposes without breaking the check.
Have the AMD driver properly declare that the special domain it created is
actually an IDENTITY domain.
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: stable@vger.kernel.org
Fixes: 512881eacf ("bus: platform,amba,fsl-mc,PCI: Add device DMA ownership management")
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0-v1-ea566e16b06b+811-amd_owner_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The global rwsem dmar_global_lock was introduced by commit 3a5670e8ac
("iommu/vt-d: Introduce a rwsem to protect global data structures"). It
is used to protect DMAR related global data from DMAR hotplug operations.
The dmar_global_lock used in the intel_iommu_init() might cause recursive
locking issue, for example, intel_iommu_get_resv_regions() is taking the
dmar_global_lock from within a section where intel_iommu_init() already
holds it via probe_acpi_namespace_devices().
Using dmar_global_lock in intel_iommu_init() could be relaxed since it is
unlikely that any IO board must be hot added before the IOMMU subsystem is
initialized. This eliminates the possible recursive locking issue by moving
down DMAR hotplug support after the IOMMU is initialized and removing the
uses of dmar_global_lock in intel_iommu_init().
Fixes: d5692d4af0 ("iommu/vt-d: Fix suspicious RCU usage in probe_acpi_namespace_devices()")
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/894db0ccae854b35c73814485569b634237b5538.1657034828.git.robin.murphy@arm.com
Link: https://lore.kernel.org/r/20220718235325.3952426-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
