The calibrated timestamp is calculated from the nominal value using the
formula:
ts_gain[ns] ≈ ts_sensitivity - (ts_trim_coeff * val) / 1000.
The values of ts_sensitivity and ts_trim_coeff are not the same for all
devices, so it is necessary to differentiate them based on the part name.
For the correct values please consult the relevant AN.
Fixes: cb3b6b8e1b ("iio: imu: st_lsm6dsx: add odr calibration feature")
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI the units after application of scale and offset are
milli degree celsius for temperature thresholds and milli percent for
relative humidity thresholds. Currently the resulting units are degree
celsius for temperature thresholds and hysteresis and percent for relative
humidity thresholds and hysteresis. Change scale factor to fix this issue.
Fixes: 3ad0e7e5f0 ("iio: humidity: hdc3020: add threshold events support")
Reported-by: Chris Lesiak <chris.lesiak@licorbio.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI the units after application of scale and offset are
milli degrees for temperature measurements and milli percent for relative
humidity measurements. Currently the resulting units are degree celsius for
temperature measurements and percent for relative humidity measurements.
Change scale factor to fix this issue.
Fixes: c9180b8e39 ("iio: humidity: Add driver for ti HDC302x humidity sensors")
Reported-by: Chris Lesiak <chris.lesiak@licorbio.com>
Suggested-by: Chris Lesiak <chris.lesiak@licorbio.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The `decimator` and `batch` fields of struct st_lsm6dsx_settings
are arrays indexed by sensor type, not by sensor hardware
identifier; moreover, the `batch` field is only used for the
accelerometer and gyroscope.
Change the array size for `decimator` from ST_LSM6DSX_MAX_ID to
ST_LSM6DSX_ID_MAX, and change the array size for `batch` from
ST_LSM6DSX_MAX_ID to 2; move the enum st_lsm6dsx_sensor_id
definition so that the ST_LSM6DSX_ID_MAX value is usable within
the struct st_lsm6dsx_settings definition.
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is an race-condition where device is not full working after SW reset.
Therefore it's necessary to wait some time after reset and verify shadow
registers values by reading and comparing the values before/after reset.
This mechanism is described in datasheet at least from revision D.
Fixes: 12ed27863e ("iio: accel: Add driver support for ADXL355")
Signed-off-by: Valek Andrej <andrej.v@skyrain.eu>
Signed-off-by: Kessler Markus <markus.kessler@hilti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix temperature channel not working due to gain and offset not being
initialized. For channels other than the voltage ones calibration is
skipped (which is OK). However that results in the calibration register
values tracked in st->channels[i].cfg all being zero. These zeros are
later written to hardware before a measurement is made which caused the
raw temperature readings to be always 8388608 (0x800000).
To fix it, we just make sure the gain and offset values are set to the
default values and still return early without doing an internal
calibration.
While here, add a comment explaining why we don't bother calibrating
the temperature channel.
Fixes: 47036a03a3 ("iio: adc: ad7124: Implement internal calibration at probe time")
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If an error occurs after a successful mfd_add_devices() call, it should be
undone by a corresponding mfd_remove_devices() call, as already done in the
remove function.
Fixes: 50dd64d57e ("iio: common: ssp_sensors: Add sensorhub driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use correct argument to iio_str_to_fixpoint() to parse 3 decimal places.
iio_str_to_fixpoint() has a bit of an unintuitive API where the
fract_mult parameter is the multiplier of the first decimal place as if
it was already an integer. So to get 3 decimal places, fract_mult must
be 100 rather than 1000.
Fixes: 96ccdbc07a ("staging:iio:adc:ad7280a: Standardize extended ABI naming")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Wire up the .get_dma_dev() callback to use the DMA buffer infrastructure's
implementation. This ensures that DMABUF operations use the correct DMA
device for mapping, which is essential for proper operation on systems
where memory is mapped above the 32-bit range.
Without this callback, the core would fall back to using the IIO device's
parent, which may not have the appropriate DMA mask configuration for
high memory access.
Fixes: 7a86d46998 ("iio: buffer-dmaengine: Support new DMABUF based userspace API")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Implement the .get_dma_dev() callback for DMA buffers by returning the
device that owns the DMA channel. This allows the core DMABUF
infrastructure to properly map DMA buffers using the correct device,
avoiding the need for bounce buffers on systems where memory is mapped
above the 32-bit range.
The function returns the DMA queue's device, which is the actual device
responsible for DMA operations in buffer-dma implementations.
Cc: stable@vger.kernel.org
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a new buffer accessor .get_dma_dev() in order to get the
struct device responsible for actually providing the dma channel. We
cannot assume that we can use the parent of the IIO device for mapping
the DMA buffer. This becomes important on systems (like the Xilinx/AMD
zynqMP Ultrascale) where memory (or part of it) is mapped above the
32 bit range. On such systems and given that a device by default has
a dma mask of 32 bits we would then need to rely on bounce buffers (to
swiotlb) for mapping memory above the dma mask limit.
In the process, add an iio_buffer_get_dma_dev() helper function to get
the proper DMA device.
Cc: stable@vger.kernel.org
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correction of meas_time_us initialization based on an observation and
partial patch by David Lechner.
The constant part of the measurement time (as described in the
datasheet and implemented in the BM(P/E)2 Sensor API) was apparently
forgotten (it was already correctly applied for the BMP380) and is now
used.
There was also another thinko in bmp280_wait_conv:
data->oversampling_humid can actually have a value of 0 (for an
oversampling_ratio of 1), so it can not be used to detect the presence
of the humidity measurement capability. Use
data->chip_info->oversampling_humid_avail instead, which is NULL for
chips that cannot measure humidity and therefore must skip that part
of the calculation.
Closes: https://lore.kernel.org/linux-iio/875xgfg0wz.fsf@Gerda.invalid/
Fixes: 26ccfaa9dd ("iio: pressure: bmp280: Use sleep and forced mode for oneshot captures")
Suggested-by: David Lechner <dlechner@baylibre.com>
Tested-by: Achim Gratz <Achim.Gratz@Stromeko.DE>
Signed-off-by: Achim Gratz <Achim.Gratz@Stromeko.DE>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initially st,adc-alt-channel property was defined as an enum in the DFSDM
binding. The DFSDM binding has been changed to use the new IIO backend
framework, along with the adoption of IIO generic channels.
In this new binding st,adc-alt-channel is defined as a boolean property,
but it is still handled has an enum in DFSDM driver.
Fix st,adc-alt-channel property handling in DFSDM driver.
Fixes: 3208fa0cd9 ("iio: adc: stm32-dfsdm: adopt generic channels bindings")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a special case to double the SPI offload trigger rate when all
channels of a single-ended chip are enabled in a buffered read.
The single-ended chips in the AD738x family can only do simultaneous
sampling of half their channels and have a multiplexer to allow reading
the other half. To comply with the IIO definition of sampling_frequency,
we need to trigger twice as often when the sequencer is enabled to so
that both banks can be read in a single sample period.
Fixes: bbeaec81a0 ("iio: ad7380: add support for SPI offload")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously, the driver always used the amount of precision bits of
differential input channels to provide the scale to mV. Though,
differential and common-mode voltage channels have different amount of
precision bits and the correct number of precision bits must be considered
to get to a proper mV scale factor for each one. Use channel specific
number of precision bits to provide the correct scale value for each
channel.
Fixes: de67f28abe ("iio: adc: ad4030: check scan_type for error")
Fixes: 949abd1ca5 ("iio: adc: ad4030: add averaging support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy()"
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
Pull SCSI fixes from James Bottomley:
"Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window.
The most important one is the qla2xxx which reverts a conversion to
fix flexible array member warnings, that went up in this merge window
but which turned out on further testing to be causing data corruption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Include UTP error in INT_FATAL_ERRORS
scsi: ufs: sysfs: Make HID attributes visible
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
scsi: ufs: core: Fix PM QoS mutex initialization
scsi: ufs: core: Fix runtime suspend error deadlock
Revert "scsi: qla2xxx: Fix memcpy() field-spanning write issue"
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Pull x86 cleanups from Borislav Petkov:
- Simplify inline asm flag output operands now that the minimum
compiler version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support
for various instruction mnemonics now that the minimum assembler
version supports them all
- The usual cleanups all over the place
* tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove code depending on __GCC_ASM_FLAG_OUTPUTS__
x86/sgx: Use ENCLS mnemonic in <kernel/cpu/sgx/encls.h>
x86/mtrr: Remove license boilerplate text with bad FSF address
x86/asm: Use RDPKRU and WRPKRU mnemonics in <asm/special_insns.h>
x86/idle: Use MONITORX and MWAITX mnemonics in <asm/mwait.h>
x86/entry/fred: Push __KERNEL_CS directly
x86/kconfig: Remove CONFIG_AS_AVX512
crypto: x86 - Remove CONFIG_AS_VPCLMULQDQ
crypto: X86 - Remove CONFIG_AS_VAES
crypto: x86 - Remove CONFIG_AS_GFNI
x86/kconfig: Drop unused and needless config X86_64_SMP
Pull slab fix from Vlastimil Babka:
"A NULL pointer deref hotfix"
* tag 'slab-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: fix barn NULL pointer dereference on memoryless nodes
Pull more updates from Andrew Morton:
"Just one series here - Mike Rappoport has taught KEXEC handover to
preserve vmalloc allocations across handover"
* tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib/test_kho: use kho_preserve_vmalloc instead of storing addresses in fdt
kho: add support for preserving vmalloc allocations
kho: replace kho_preserve_phys() with kho_preserve_pages()
kho: check if kho is finalized in __kho_preserve_order()
MAINTAINERS, .mailmap: update Umang's email address
Pull misc fixes from Andrew Morton:
"7 hotfixes. All 7 are cc:stable and all 7 are for MM.
All singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
fsnotify: pass correct offset to fsnotify_mmap_perm()
mm/ksm: fix flag-dropping behavior in ksm_madvise
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
mm/rmap: fix soft-dirty and uffd-wp bit loss when remapping zero-filled mTHP subpage to shared zeropage
mm/thp: fix MTE tag mismatch when replacing zero-filled subpages
memcg: skip cgroup_file_notify if spinning is not allowed
The fix to use a per CPU buffer to read user space tested only the writes
to trace_marker. But it appears that the selftests are missing tests to
the trace_maker_raw file. The trace_maker_raw file is used by applications
that writes data structures and not strings into the file, and the tools
read the raw ring buffer to process the structures it writes.
The fix that reads the per CPU buffers passes the new per CPU buffer to
the trace_marker file writes, but the update to the trace_marker_raw write
read the data from user space into the per CPU buffer, but then still used
then passed the user space address to the function that records the data.
Pass in the per CPU buffer and not the user space address.
TODO: Add a test to better test trace_marker_raw.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/20251011035243.386098147@kernel.org
Fixes: 64cf7d058a ("tracing: Have trace_marker use per-cpu data to read user space")
Reported-by: syzbot+9a2ede1643175f350105@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68e973f5.050a0220.1186a4.0010.GAE@google.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
After commit 5ab23c7923 ("modpost: Create modalias for builtin
modules"), relocatable RISC-V kernels with CONFIG_KASAN=y start failing
when attempting to strip the module device table symbols:
riscv64-linux-objcopy: not stripping symbol `__mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table' because it is named in a relocation
make[4]: *** [scripts/Makefile.vmlinux:97: vmlinux] Error 1
The relocation appears to come from .LASANLOC5 in .data.rel.local:
$ llvm-objdump --disassemble-symbols=.LASANLOC5 --disassemble-all -r drivers/irqchip/irq-starfive-jh8100-intc.o
drivers/irqchip/irq-starfive-jh8100-intc.o: file format elf64-littleriscv
Disassembly of section .data.rel.local:
0000000000000180 <.LASANLOC5>:
...
1d0: 0000 unimp
00000000000001d0: R_RISCV_64 __mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table
...
This section appears to come from GCC for including additional
information about global variables that may be protected by KASAN.
There appears to be no way to opt out of the generation of these symbols
through either a flag or attribute. Attempting to remove '.LASANLOC*'
with '--strip-symbol' results in the same error as above because these
symbols may refer to (thus have relocation between) each other.
Avoid this build breakage by switching to '--strip-unneeded-symbol' for
removing __mod_device_table__ symbols, as it will only remove the symbol
when there is no relocation pointing to it. While this may result in a
little more bloat in the symbol table in certain configurations, it is
not as bad as outright build failures.
Fixes: 5ab23c7923 ("modpost: Create modalias for builtin modules")
Reported-by: Charles Mirabile <cmirabil@redhat.com>
Closes: https://lore.kernel.org/20251007011637.2512413-1-cmirabil@redhat.com/
Suggested-by: Alexey Gladkov <legion@kernel.org>
Tested-by: Nicolas Schier <nsc@kernel.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Pull more drm fixes from Dave Airlie:
"Just the follow up fixes for rc1 from the next branch, amdgpu and xe
mostly with a single v3d fix in there.
amdgpu:
- DC DCE6 fixes
- GPU reset fixes
- Secure diplay messaging cleanup
- MES fix
- GPUVM locking fixes
- PMFW messaging cleanup
- PCI US/DS switch handling fix
- VCN queue reset fix
- DC FPU handling fix
- DCN 3.5 fix
- DC mirroring fix
amdkfd:
- Fix kfd process ref leak
- mmap write lock handling fix
- Fix comments in IOCTL
xe:
- Fix build with clang 16
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation
- Do not try late bind firmware when running as VF since it shouldn't
handle firmware loading
- Fix idle assertion for local BOs
- Fix uninitialized variable for late binding
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do
- Fix lock handling on suspend error path
- Fix I2C controller resume after S3
v3d:
- fix fence locking"
* tag 'drm-next-2025-10-11-1' of https://gitlab.freedesktop.org/drm/kernel: (34 commits)
drm/amd/display: Incorrect Mirror Cositing
drm/amd/display: Enable Dynamic DTBCLK Switch
drm/amdgpu: Report individual reset error
drm/amdgpu: partially revert "revert to old status lock handling v3"
drm/amd/display: Fix unsafe uses of kernel mode FPU
drm/amd/pm: Disable VCN queue reset on SMU v13.0.6 due to regression
drm/amdgpu: Fix general protection fault in amdgpu_vm_bo_reset_state_machine
drm/amdgpu: Check swus/ds for switch state save
drm/amdkfd: Fix two comments in kfd_ioctl.h
drm/amd/pm: Avoid interface mismatch messaging
drm/amdgpu: Merge amdgpu_vm_set_pasid into amdgpu_vm_init
drm/amd/amdgpu: Fix the mes version that support inv_tlbs
drm/amd: Check whether secure display TA loaded successfully
drm/amdkfd: Fix mmap write lock not release
drm/amdkfd: Fix kfd process ref leaking when userptr unmapping
drm/amdgpu: Fix for GPU reset being blocked by KIQ I/O.
drm/amd/display: Disable scaling on DCE6 for now
drm/amd/display: Properly disable scaling on DCE6
drm/amd/display: Properly clear SCL_*_FILTER_CONTROL on DCE6
drm/amd/display: Add missing DCE6 SCL_HORZ_FILTER_INIT* SRIs
...
Pull drm fixes from Dave Airlie:
"Some fixes leftover from our fixes branch, just nouveau and vmwgfx:
nouveau:
- Return errno code from TTM move helper
vmwgfx:
- Fix null-ptr access in cursor code
- Fix UAF in validation
- Use correct iterator in validation"
* tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel:
drm/nouveau: fix bad ret code in nouveau_bo_move_prep
drm/vmwgfx: Fix copy-paste typo in validation
drm/vmwgfx: Fix Use-after-free in validation
drm/vmwgfx: Fix a null-ptr access in the cursor snooper
Pull devicetree fixes from Rob Herring:
- Allow child nodes on renesas-bsc bus binding
- Drop node name pattern on allwinner,sun50i-a64-de2 bus binding
- Switch DT patchwork to kernel.org from ozlabs.org
- Fix some typos in docs and bindings
- Fix reference count in PCI node unittest
* tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: bus: renesas-bsc: allow additional properties
dt-bindings: bus: allwinner,sun50i-a64-de2: don't check node names
MAINTAINERS: Move DT patchwork to kernel.org
of: unittest: Fix device reference count leak in of_unittest_pci_node_verify
of: doc: Fix typo in doc comments.
dt-bindings: mmc: Correct typo "upto" to "up to"
Allow additional properties to enable devices attached to the bus.
Fixes warnings like these:
arch/arm/boot/dts/renesas/sh73a0-kzm9g.dtb: bus@fec10000 (renesas,bsc-sh73a0): Unevaluated properties are not allowed ('ethernet@10000000' was unexpected)
arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dtb: bus@fec10000 (renesas,bsc-r8a73a4): Unevaluated properties are not allowed ('ethernet@8000000', 'flash@0' were unexpected)
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Node names are already and properly checked by the core schema. No need
to do it again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[robh: Also drop [A-F] in unit address]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull ceph updates from Ilya Dryomov:
- some messenger improvements (Eric and Max)
- address an issue (also affected userspace) of incorrect permissions
being granted to users who have access to multiple different CephFS
instances within the same cluster (Kotresh)
- a bunch of assorted CephFS fixes (Slava)
* tag 'ceph-for-6.18-rc1' of https://github.com/ceph/ceph-client:
ceph: add bug tracking system info to MAINTAINERS
ceph: fix multifs mds auth caps issue
ceph: cleanup in ceph_alloc_readdir_reply_buffer()
ceph: fix potential NULL dereference issue in ceph_fill_trace()
libceph: add empty check to ceph_con_get_out_msg()
libceph: pass the message pointer instead of loading con->out_msg
libceph: make ceph_con_get_out_msg() return the message pointer
ceph: fix potential race condition on operations with CEPH_I_ODIRECT flag
ceph: refactor wake_up_bit() pattern of calling
ceph: fix potential race condition in ceph_ioctl_lazyio()
ceph: fix overflowed constant issue in ceph_do_objects_copy()
ceph: fix wrong sizeof argument issue in register_session()
ceph: add checking of wait_for_completion_killable() return value
ceph: make ceph_start_io_*() killable
libceph: Use HMAC-SHA256 library instead of crypto_shash
Pull more smb client updates from Steve French:
- fix i_size in fallocate
- two truncate fixes
- utime fix
- minor cleanups
- SMB1 fixes
- improve error check in read
- improve perf of copy file_range (copy_chunk)
* tag 'v6.18-rc-part2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
cifs: Add comments for DeletePending assignments in open functions
cifs: Add fallback code path for cifs_mkdir_setinfo()
cifs: Allow fallback code in smb_set_file_info() also for directories
cifs: Query EA $LXMOD in cifs_query_path_info() for WSL reparse points
smb: client: remove cfids_invalidation_worker
smb: client: remove redudant assignment in cifs_strict_fsync()
smb: client: fix race with fallocate(2) and AIO+DIO
smb: client: fix missing timestamp updates after utime(2)
smb: client: fix missing timestamp updates after ftruncate(2)
smb: client: fix missing timestamp updates with O_TRUNC
cifs: Fix copy_to_iter return value check
smb: client: batch SRV_COPYCHUNK entries to cut round trips
smb: client: Omit an if branch in smb2_find_smb_tcon()
smb: client: Return directly after a failed genlmsg_new() in cifs_swn_send_register_message()
smb: client: Use common code in cifs_do_create()
smb: client: Improve unlocking of a mutex in cifs_get_swn_reg()
smb: client: Return a status code only as a constant in cifs_spnego_key_instantiate()
smb: client: Use common code in cifs_lookup()
smb: client: Reduce the scopes for a few variables in two functions
Pull Xtensa updates from Max Filippov:
- minor cleanups
* tag 'xtensa-20251010' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: use HZ_PER_MHZ in platform_calibrate_ccount
xtensa: simdisk: add input size check in proc_write_simdisk
Pull block fixes from Jens Axboe:
- Don't include __GFP_NOWARN for loop worker allocation, as it already
uses GFP_NOWAIT which has __GFP_NOWARN set already
- Small series cleaning up the recent bio_iov_iter_get_pages() changes
- loop fix for leaking the backing reference file, if validation fails
- Update of a comment pertaining to disk/partition stat locking
* tag 'block-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
loop: remove redundant __GFP_NOWARN flag
block: move bio_iov_iter_get_bdev_pages to block/fops.c
iomap: open code bio_iov_iter_get_bdev_pages
block: rename bio_iov_iter_get_pages_aligned to bio_iov_iter_get_pages
block: remove bio_iov_iter_get_pages
block: Update a comment of disk statistics
loop: fix backing file reference leak on validation error
Pull io_uring fixes from Jens Axboe:
- Fixup indentation in the UAPI header
- Two fixes for zcrx. One fixes receiving too much in some cases, and
the other deals with not correctly incrementing the source in the
fallback copy loop
- Fix for a race in the IORING_OP_WAITID command, where there was a
small window where the request would be left on the wait_queue_head
list even though it was being canceled/completed
- Update liburing git URL in the kernel tree
* tag 'io_uring-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/zcrx: increment fallback loop src offset
io_uring/zcrx: fix overshooting recv limit
io_uring: use tab indentation for IORING_SEND_VECTORIZED comment
io_uring/waitid: always prune wait queue entry in io_waitid_wait()
io_uring: update liburing git URL
This is a series to address some problems that were exposed by the
recent modules.builtin.modinfo series that landed in commit c7d3dd9163
("Merge patch series "Add generated modalias to
modules.builtin.modinfo"").
The third patch is not directly related to the aforementioned series, as
the warning it fixes happens prior to the series but commit 8d18ef04f9
("s390: vmlinux.lds.S: Reorder sections") from the series creates
conflicts in this area, so I included it here.
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-0-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
When building s390 defconfig with binutils older than 2.32, there are
several warnings during the final linking stage:
s390-linux-ld: .tmp_vmlinux1: warning: allocated section `.got.plt' not in segment
s390-linux-ld: .tmp_vmlinux2: warning: allocated section `.got.plt' not in segment
s390-linux-ld: vmlinux.unstripped: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: vmlinux: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: st7afZyb: warning: allocated section `.got.plt' not in segment
binutils commit afca762f598 ("S/390: Improve partial relro support for
64 bit") [1] in 2.32 changed where .got.plt is emitted, avoiding the
warning.
The :NONE in the .vmlinux.info output section description changes the
segment for subsequent allocated sections. Move .vmlinux.info right
above the discards section to place all other sections in the previously
defined segment, .data.
Fixes: 30226853d6 ("s390: vmlinux.lds.S: explicitly handle '.got' and '.plt' sections")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=afca762f598d453c563f244cd3777715b1a0cb72 [1]
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-3-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
