ath.git patches for v5.18. Major changes:
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix following coccicheck warning:
./drivers/net/wireless/mediatek/mt76/mt7915/mac.c:768:29-31:
WARNING !A || A && B is equivalent to !A || B
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, do not aggregate injected frames in
HW A-MSDU block.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, mt7915e does not enable thermal management until the default
thermal zone does not reach a trip point. If the rest of the system
have better cooling than the wireless hardware, then it is possible that
the wireless chip can overheat while the rest of the system is fine.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware-controlled actual throttle state was previously available
by reading the cooling_device, but this confused the thermal subsystem.
Add a hwmon attribute to get it instead.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915e registers a cooling_device with wrong semantics:
1. cooling_device expect that higher states values should cool more, but
mt7915e did the opposite... with the exception of state == 0, which
should "disable thermal management", but does not seem to have any
effect since the previous state is kept.
The result is that when the thermal zone heats up a bit and bumps the
cooling_device state from 0 to 1 to cool a bit, the performance is
destroyed, and when going back from 1 to 0, the performance stays bad.
2. Reading the cooling_device state does not always return the last
written state, but can return the actual hardware throttle state,
which is different.
This is a problem because the mt7915 firmware actually implement the
equivalent of a thermal zone with trip points. Setting the cooling
device state actually changes the throttles at each trip point, so the
following could occur if the first issue is fixed:
- thermal subsystem set state to 100% power (state=0)
- mt7915e driver set trip throttles to [100%, 50%, 25%, 12%]
- hardware heats up and decides to switch to 50% power
- thermal subsystem see that power is 50% (state=50), decide to increase
it to 60% (state=40) because the rest of the system is cool.
- mt7915e driver set trip throttle to [60%, 30%, 15%, 7%]
- hardware thus switches to 30% power
[race to the bottom continues...]
This patch corrects the semantics of the cooling_device to the one that
the thermal subsystem expect it.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The muru enable/disable are only set after the first station connection.
Without this patch, the firmware couldn't enable muru
if the first connected station is non-HE type.
Fixes: 16bff457dd ("mt76: mt7915: rework mt7915_mcu_sta_muru_tlv()")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer chips such as MT7915 require up to 16-bits for this field.
Fixes: 49126ac1f8 ("mt76: connac: move mt76_connac_mcu_bss_basic_tlv in connac module")
Signed-off-by: Chad Monroe <chad.monroe@smartrg.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in mt7915_mac_tx_free routine:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] *cur_info
got restricted __le32 *
warning: cast to restricted __le32
Fixes: c17780e7b2 ("mt76: mt7915: add txfree event v3")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warnings:
warning: incorrect type in initializer (different base types)
expected restricted __le16 [usertype] msg_type
got int
warning: incorrect type in assignment (different base types)
expected restricted __le32 [usertype] timestamp
got unsigned int
Fixes: 988845c936 ("mt76: mt7915: add support for passing chip/firmware debug data to user space")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The following error is see from the compiler:
mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’:
mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
The issue is due to allocating a buffer as string storage.
Fix by converting to a dynamical allocation of the buffer.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reading through the commit history, it looks like
there is no special need why we must skip the first 4 bytes
in this trace call:
trace_ath10k_htt_rx_desc(ar, (void*)rx_desc + sizeof(u32),
hw->rx_desc_ops->rx_desc_size - sizeof(u32));
found in the function ath10k_htt_rx_amsdu_pop in the file htt_rx.c
i think the original author
(who is also the one who added rx_desc tracing capabilities
in a0883cf7e7) just wanted to trace the rx_desc contents,
ignoring the fw_rx_desc_base info field
(which is the part being skipped over).
But the trace_ath10k_htt_rx_desc later added
don't care about skipping it, so it may be good
to uniform this call to the others in the file.
But this would change the output of the trace and
thus it may be a problem for tools that rely on it.
Therefore I propose until further discussion
to just keep it as it is and just fix the pointer arithmetic bug.
Add missing void* cast to rx descriptor pointer in order to
properly skip the initial 4 bytes of the rx descriptor
when passing it to trace_ath10k_htt_rx_desc trace function.
This fixes the pointer arithmetic error detected
by Dan Carpenter's static analysis tool.
Fixes: 6bae9de622 ("ath10k: abstract htt_rx_desc structure")
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Signed-off-by: Francesco Magliocca <franciman12@gmail.com>
Link: https://lore.kernel.org/ath10k/20220201130900.GD22458@kili/
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220221122638.7971-1-franciman12@gmail.com
Target copies spectral report and CFR report through dbring to
host for further processing. This mechanism involves ring and
buffer management in the Host, FW, and uCode, where improper
tail pointer update issues are seen.
This dbring debug support help to debug such issues by tracking
head and tail pointer movement along with the timestamp at which
each buffer is received and replenished.
Provide a debugfs interface to enalbe/disable dbring debug
support and dump the dbring debug entries.
Also introduced a new hardware param to add dbring debugfs support
for few hardwares which are using dbings.
Usage:
echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/
mac0/enable_dbr_debug
dbr_id: 0 for spectral and 1 for CFR
val: 0 - disable, 1 - enable.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645366059-11798-1-git-send-email-quic_vnaralas@quicinc.com
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before, the hardware would be allowed to transmit injected 802.11 MPDUs
as A-MSDU. This resulted in corrupted frames being transmitted. Now,
injected MPDUs are transmitted as-is, without A-MSDU.
The fix was verified with frame injection on MT7915 hardware, both with
and without the injected frame being encrypted.
If the hardware cannot do A-MSDU aggregation on MPDUs, this problem
would also be present in the TX path where mac80211 does the 802.11
encapsulation. However, I have not observed any such problem when
disabling IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD to force that mode.
Therefore this fix is isolated to injected frames only.
The same A-MSDU logic is also present in the mt7921 driver, so it is
likely that this fix should be applied there too. I do not have access
to mt7921 hardware so I have not been able to test that.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
