If neither a "hif_mspi" nor "mspi" resource is present, the driver will
just early exit in probe but still return success. Apart from not doing
anything meaningful, this would then also lead to a null pointer access
on removal, as platform_get_drvdata() would return NULL, which it would
then try to dereference when trying to unregister the spi master.
Fix this by unconditionally calling devm_ioremap_resource(), as it can
handle a NULL res and will then return a viable ERR_PTR() if we get one.
The "return 0;" was previously a "goto qspi_resource_err;" where then
ret was returned, but since ret was still initialized to 0 at this place
this was a valid conversion in 63c5395bb7 ("spi: bcm-qspi: Fix
use-after-free on unbind"). The issue was not introduced by this commit,
only made more obvious.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Link: https://lore.kernel.org/r/20230629134306.95823-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
I recently came across an issue with the Atmel spi controller driver
which would stop my transfers after a too small timeout when performing
big transfers (reading a 4MiB flash in one transfer). My initial idea
was to derive a the maximum amount of time a transfer would take
depending on its size and use that as value to avoid erroring-out when
not relevant. Mark wanted to go further by creating a core helper doing
that, based on the heuristics from the sun6i driver.
Here is a small series of 3 patches doing exactly that.
A helper was recently added to the core to factorize common code between
drivers, like the amount of time a driver should wait for a transfer to
happen.
It is of course possible to use a default value (like eg. 1s) but it is
way stronger to adapt this amount of time to the transfer. Indeed, long
transfers (eg. 4MiB) on a slow single-spi bus might take more than the
usual second of timeout and prevent lengthy transfers.
The core helper was heavily inspired by the logic applied in this
driver, the only difference being the minimum amount of time which was
enlarged from 0.1s to 0.5s.
Use this helper instead of open-coding it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-4-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A slow SPI bus clocks at ~20MHz, which means it would transfer about
2500 bytes per second with a single data line. Big transfers, like when
dealing with flashes can easily reach a few MiB. The current DMA timeout
is set to 1 second, which means any working transfer of about 4MiB will
always be cancelled.
With the above derivations, on a slow bus, we can assume every byte will
take at most 0.4ms. Said otherwise, we could add 4ms to the 1-second
timeout delay every 10kiB. On a 4MiB transfer, it would bring the
timeout delay up to 2.6s which still seems rather acceptable for a
timeout.
The consequence of this is that long transfers might be allowed, which
hence requires the need to interrupt the transfer if wanted by the
user. We can hence switch to the _interruptible variant of
wait_for_completion. This leads to a little bit more handling to also
handle the interrupted case but looks really acceptable overall.
While at it, we drop the useless, noisy and redundant WARN_ON() call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ryan Wanner <ryan.wanner@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-3-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Big transfers might take a bit of time, too constraining timeouts might
lead to false positives. In order to simplify the drivers work and with
the goal of factorizing code in mind, let's add a helper that can be
used by any spi controller driver to derive a relevant per-transfer
timeout value.
The logic is simple: we know how much time it would take to transfer a
byte, we can easily derive the total theoretical amount of time involved
for each transfer. We multiply it by two to have a bit of margin and
enforce a minimum of 500ms.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-2-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andi Shyti <andi.shyti@kernel.org>:
Two small cleanups in the probe function. The first puts in use
the managed spi master allocation while the second implements the
dev_err_probe() function.
The Intel Mount Evans SoC's Integrated Management Complex uses the SPI
controller for access to a NOR SPI FLASH. However, the SoC doesn't
provide a mechanism to override the native chip select signal.
This driver doesn't use DMA for memory operations when a chip select
override is not provided due to the native chip select timing behavior.
As a result no DMA configuration is done for the controller and this
configuration is not tested.
The controller also has an errata where a full TX FIFO can result in
data corruption. The suggested workaround is to never completely fill
the FIFO. The TX FIFO has a size of 32 so the fifo_len is set to 31.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230606145402.474866-2-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 87c614175b (spi: spi-imx: fix MX51_ECSPI_* macros when cs >
3) ensured that the argument passed to the macros was masked with &3,
so that we no longer write outside the intended fields in the various
control registers. When all chip selects are gpios, this works just
fine.
However, when a mix of native and gpio chip selects are in use, that
masking is too naive. Say, for example, that SS0 is muxed as native
chip select, and there is also a chip at 4 (obviously with a gpio
cs). In that case, when accessing the latter chip, both the SS0 pin
and the gpio pin will be asserted low.
The fix for this is to use the ->unused_native_cs value as channel
number for any spi device which uses a gpio as chip select.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230602115731.708883-1-linux@rasmusvillemoes.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Boerge Struempfel <boerge.struempfel@gmail.com>:
Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
Hello,
compared to (implicit) v1 sent in March with Message-Id:
<20230309094704.2568531-1-u.kleine-koenig@pengutronix.de>, I reworked
patch 1 on feedback by AngeloGioacchino Del Regno. Patches 2 and 3 got
his Reviewed-by.
Best regards
Uwe
Uwe Kleine-König (3):
spi: mt65xx: Properly handle failures in .remove()
spi: mt65xx: Convert to platform remove callback returning void
spi: mt65xx: Don't disguise a "return 0" as "return ret"
drivers/spi/spi-mt65xx.c | 30 +++++++++++++++++-------------
1 file changed, 17 insertions(+), 13 deletions(-)
base-commit: ac9a78681b
--
2.39.2
In order to increase usability, the command line options are sorted into
logical groups. In addition, the usage string was sorted alphabetically,
and the missing parameters '8','i' and 'o' were added. Furthermore, the
option descriptions were moved further to the right, in order to allow
for longer option names.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-5-boerge.struempfel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, the spi-imx controller pulls the mosi line high, whenever it
is idle. This behaviour can be inverted per CS by setting the
corresponding DATA_CTL bit in the config register of the controller.
Also, since the controller mode-bits have to be touched anyways, the
SPI_CPOL and SPI_CPHA are replaced by the combined SPI_MODE_X_MASK flag.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-3-boerge.struempfel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-2-boerge.struempfel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530081648.2199419-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Fixes: 612762e82a ("spi: qup: Add DMA capabilities")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230518-spi-qup-clk-defer-v1-1-f49fc9ca4e02@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
