After the recent corrections to the R-Car gen2/3 LVDS startup code, already
similar enough at their ends rcar_lvds_enable_gen{2|3}() started asking for
a merge and it's becoming actually necessary with the addition of the R-Car
V3M (R8A77970) support -- this gen3 SoC has gen2-like LVDPLLCR layout.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Set the LVDS mode and input before turning channels on]
[Rebased, coding style changes]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
According to the latest revision 2.00 of the R-Car Gen2 manual, the LVDS
and the bias circuit must be enabled after the LVDS I/O pins are
enabled, not before. Fix the Gen2 LVDS startup sequence accordingly.
While at it, also fix the comment preceding the first LVDCR0 write that
still talks about hardcoding the LVDS mode 0.
Fixes: 90374b5c25 ("drm/rcar-du: Add internal LVDS encoder support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
According to the latest versions of both the Gen2 and Gen3 datasheets,
the operating range for the LVDS clock is 31 MHz to 148.5 MHz on all
SoCs. Update the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
The LVDCR1 register for the R-Car gen3 SoCs was documented as having the
layout different from the gen2 SoCs in the early R-Car gen3 manuals but
since v0.52 the LVDCR1 layout is described as being the same as on the gen2
SoCs; the old CHn control values are said to be prohibited now (and there
seems to be no valid output signal when they are used).
Fixes: 6bc2e15cf2 ("drm: rcar-du: lvds: Add R-Car Gen3 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
On Gen3 hardware the VSP compositor is required for display. Enable it
by default in the kernel configuration. The option is kept
user-configurable for testing purpose on Gen2 platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
In general, PLL has VCO (= Voltage controlled oscillator),
one of the very important electronic feature called as "jitter"
is related to this VCO.
In academic generalism, VCO should be maximum to be more small jitter.
In high frequency clock, jitter will be large impact.
Thus, selecting Hi VCO is general theory.
fin fvco fout fclkout
in --> [1/M] --> |PD| -> [LPF] -> [VCO] -> [1/P] -+-> [1/FDPLL] -> out
+-> | | |
| |
+-----------------[1/N]<-------------+
fclkout = fvco / P / FDPLL -- (1)
In PD, it will loop until fin/M = fvco/P/N
fvco = fin * P * N / M -- (2)
(1) + (2) indicates
fclkout = fin * N / M / FDPLL
In this device, N = (n + 1), M = (m + 1), P = 2, FDPLL = (fdpll + 1).
fclkout = fin * (n + 1) / (m + 1) / (fdpll + 1)
This is the datasheet formula.
One note here is that it should be 2kHz < fvco < 4096MHz
To be smaller jitter, fvco should be maximum,
in other words, N as large as possible, M as small as possible driver
should select. Here, basically M=1.
This patch do it.
Reported-by: HIROSHI INOSE <hiroshi.inose.rb@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Small clarifications in comments, renamed finnm to fout]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Since commit 2fc4d838aa ("drm: rcar: use generic code for managing
zpos plane property") the rcar-du driver stores the plane zpos in the
drm_plane_state structure. The commit however forgot to remove the zpos
field from the rcar_du_vsp_plane_state structure. Remove it.
Fixes: 2fc4d838aa ("drm: rcar: use generic code for managing zpos plane property")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix for pcode timeouts on BXT and GLK, cmdparser fixes and fixes
for new vbt version on CFL and CNL.
GVT contains vGPU reset enhancement, which refines vGPU reset flow
and the support of virtual aperture read/write when x-no-mmap=on
is set in KVM, which is required by a test case from Redhat and
also another fix for virtual OpRegion.
* tag 'drm-intel-next-fixes-2018-02-07' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/bios: add DP max link rate to VBT child device struct
drm/i915/cnp: Properly handle VBT ddc pin out of bounds.
drm/i915/cnp: Ignore VBT request for know invalid DDC pin.
drm/i915/cmdparser: Do not check past the cmd length.
drm/i915/cmdparser: Check reg_table_count before derefencing.
drm/i915/bxt, glk: Increase PCODE timeouts during CDCLK freq changing
drm/i915/gvt: Use KVM r/w to access guest opregion
drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on
drm/i915/gvt: only reset execlist state of one engine during VM engine reset
drm/i915/gvt: refine intel_vgpu_submission_ops as per engine ops
A few more misc fixes for 4.16.
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: re-enable CGCG on CZ and disable on ST
drm/amdgpu: disable coarse grain clockgating for ST
drm/radeon: adjust tested variable
drm/amdgpu: remove WARN_ON when VM isn't found v2
drm/amdgpu: fix locking in vega10_ih_prescreen_iv
drm/amdgpu: fix another potential cause of VM faults
drm/amdgpu: use queue 0 for kiq ring
drm/ttm: Fix 'buf' pointer update in ttm_bo_vm_access_kmap() (v2)
drm/ttm: fix missing parameter change for ttm_bo_cleanup_refs
Currently we see sporadic timeouts during CDCLK changing both on BXT and
GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by
changing the frequency in a tight loop after blanking the display. The
upper bound for the completion time is 800us based on my tests, so
increase it from the current 500us to 2ms; with that I couldn't trigger
the problem either on BXT or GLK.
Note that timeouts happened during both the change notification and the
voltage level setting PCODE request. (For the latter one BSpec doesn't
require us to wait for completion before further HW programming.)
This issue is similar to
commit 2c7d0602c8 ("drm/i915/gen9: Fix PCODE polling during CDCLK
change notification")
but there the PCODE request does complete (as shown by the mbox
busy flag), only the reply we get from PCODE indicates a failure.
So there we keep resending the request until a success reply, here we
just have to increase the timeout for the one PCODE request we send.
v2:
- s/snb_pcode_request/sandybridge_pcode_write_timeout/ (Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com
(cherry picked from commit e76019a819)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
For KVMGT, the guest opregion, which is handled by VFIO, is actually a
piece of guest memory which won't be accessed by devices. So, its mfn
shouldn't be obtained through VFIO interface. This patch uses KVM r/w
interface to access the data in guest opregion.
Fix the guest opregion accessing issue when host "intel_iommu=on".
v3:
- Remove mapped flag for KVM/VFIO usage, as it's useless for KVM.
v2:
- Set the gpa correctly when invoking KVM r/w operations. (Zhenyu)
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When add 'x-no-mmap=on' for vfio-pci option, aperture access in guest
is emulated. But the vgpu_aperture_rw() function take wrong offset when
do memcpy, since vgpu->gm.aperture_va is not the base of entire aperture.
This mistake cause GPU command in guest get lost and so the seqno is not
updated in engine HWSP.
This patch fix this, and it also move the emulation code to kvmgt.
Because only vfio need to emulate it. Put aperture rw to MMIO emulation
path breaks assumptions in xengt.
v2: Remove PAGE_ALIGN for size (zhenyu)
Fixes: f090a00df9 ("drm/i915/gvt: Add emulation for BAR2 (aperture) with normal file RW approach")
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Only reset vgpu execlist state of the exact engine which gets reset
request from VM. After read context status from HWSP enabled, KMD will use
the saved CSB read pointer but not always read from MMIO. When one engine
reset happen, only the read pointer of this engine will be reset, in GVT-g
host side also need to align with this policy, otherwise VM may get wrong
CSB status after one engine reset compeleted.
v2: Split refine and fix patch, code refine(Zhenyu)
v3: Move active flag of vgpu scheduler into sched_data(Zhenyu)
Cc: Fred Gao <fred.gao@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
- initial kepler clock gating support
- atomic gamma handling fixes
- support for gp108 "secure boot" (enables acceleration, finally)
* 'linux-4.16' of git://github.com/skeggsb/linux:
drm/nouveau/clk: fix gcc-7 -Wint-in-bool-context warning
drm/nouveau/mmu: Fix trailing semicolon
drm/nouveau: Introduce NvPmEnableGating option
drm/nouveau: Add support for SLCG for Kepler2
drm/nouveau: Add support for BLCG on Kepler2
drm/nouveau: Add support for BLCG on Kepler1
drm/nouveau: Add support for basic clockgating on Kepler1
drm/nouveau/kms/nv50: fix handling of gamma since atomic conversion
drm/nouveau/kms/nv50: use INTERPOLATE_257_UNITY_RANGE LUT on newer chipsets
drm/nouveau/kms/nv50: use "low res" lut for indexed mode
drm/nouveau/kms/nv50: prepare for double-buffered LUTs
drm/nouveau/bo: add helper functions for handling pinned+mapped buffers
drm/nouveau/fbcon: add module parameter to select bits-per-pixel
drm/nouveau/secboot/gp108: implement on top of acr_r370
drm/nouveau/secboot/r370: implement support for booting LS SEC2 ucode
drm/nouveau/secboot/r370: move a bunch of r375 stuff to a new implementation
drm/nouveau: nouveau: use correct string length
drm/nouveau/drm/nouveau/mmu: fix odd_ptr_err.cocci warnings
drm/nouveau/pmu/fuc: don't use movw directly anymore
Fixes for GPU hangs and other bugs around hangcheck and result;
Fix for regression on suspend case with vgaswitcheroo;
Fixes for eDP and HDMI blank screens
Fix for protecting WC allocation to avoid overflow on page vec;
Cleanup around unpublished GLK firmware blobs, and other small fixes.
This also contains GVT pull request mostly with regression
fixes on vGPU display dmabuf, mmio switch and other misc changes.
* tag 'drm-intel-next-fixes-2018-02-01' of git://anongit.freedesktop.org/drm/drm-intel: (21 commits)
drm/i915/ppgtt: Pin page directories before allocation
drm/i915: Always run hangcheck while the GPU is busy
Revert "drm/i915: mark all device info struct with __initconst"
drm/i915/edp: Do not do link training fallback or prune modes on EDP
drm/i915: Check for fused or unused pipes
drm/i915: Protect WC stash allocation against direct reclaim
drm/i915: Only attempt to scan the requested number of shrinker slabs
drm/i915: Always call to intel_display_set_init_power() in resume_early.
drm/i915/gvt: cancel scheduler timer when no vGPU exists
drm/i915/gvt: cancel virtual vblank timer when no vGPU exists
drm/i915/gvt: Keep obj->dma_buf link NULL during exporting
drm/i915/pmu: Reconstruct active state on starting busy-stats
drm/i915: Stop getting the fault address from RING_FAULT_REG
drm/i915/guc: Add uc_fini_wq in gem_init unwind path
drm/i915: Fix using BIT_ULL() vs. BIT() for power domain masks
drm/i915: Try EDID bitbanging on HDMI after failed read
drm/i915/glk: Disable Guc and HuC on GLK
drm/i915/gvt: Do not use I915_NUM_ENGINES to iterate over the mocs regs array
drm/i915/gvt: validate gfn before set shadow page entry
drm/i915/gvt: add PLANE_KEYMAX regs to mmio track list
...
gcc thinks that interpreting a multiplication result as a bool
is confusing:
drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c: In function 'read_pll':
drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c:133:8: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
Adding a temporary variable to contain the divisor helps make
it clear what is going on and avoids that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds the NvPmEnableGating config option to nouveau, which can be
used to enable or disable clockgating for supported chipsets. Enabling
can be done by passing
config=NvPmEnableGating=1
To nouveau. If your chipset supports it, you'll see a message in your
kernel log indicating that clockgating is enabled. Since clockgating has
only had limited testing thus far, we leave this option disabled by
default for now.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
That's right, there's still more power saving to go! Starting with
kepler 2, nvidia hardware has an additional level of clockgating known
as second level clockgating. The details of this are not exact, but it
seems to work by waiting for a collection of dependent hardware blocks
to be gated before taking affect. As with the previous series, this
results in another noticeable drop in power consumption and is
programmed in the same manner.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This enables BLCG optimization for kepler1. When using clockgating,
nvidia's firmware has a set of registers which are initially programmed
by the vbios with various engine delays and other mysterious settings
that are safe enough to bring up the GPU. However, the values used by
the vbios are more power hungry then they need to be, so the nvidia driver
writes it's own more optimized set of BLCG settings before enabling
CG_CTRL. This adds support for programming the optimized BLCG values
during engine/subdev init, which enables rather significant power
savings.
This introduces the nvkm_therm_clkgate_init() helper, which we use to
program the optimized BLCG settings before enabling clockgating with
nvkm_therm_clkgate_enable.
As well, this commit shares a lot more code with Fermi since BLCG is
mostly the same there as far as we can tell. In the future, it's likely
we'll reformat the clkgate_packs for kepler1 so that they share a list
of mmio packs with Fermi.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds support for enabling automatic clockgating on nvidia GPUs for
Kepler1. While this is not technically a clockgating level, it does
enable clockgating using the clockgating values initially set by the
vbios (which should be safe to use).
This introduces two therm helpers for controlling basic clockgating:
nvkm_therm_clkgate_enable() - enables clockgating through
CG_CTRL, done after initializing the GPU fully
nvkm_therm_clkgate_fini() - prepares clockgating for suspend or
driver unload
A lot of this code was originally going to be based off of fermi;
however it turns out that while Fermi's the first line of GPUs that
introduced this kind of power saving, Fermi requires more fine tuned
control of the CG_CTRL registers from the driver while reclocking that
we don't entirely understand yet.
For the simple parts we will be sharing with Fermi for certain however,
we at least add those into a new subdev/therm/gf100.h header.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We've still been directly using the legacy crtc gamma_set() hook even
after conversion to atomic modesetting.
For userspace clients this was fine, however, fbcon will use the atomic
property when it's running on an atomic driver, which means we miss its
colormap updates - which is particularly bad for 8bpp framebuffers!
This commit converts the driver to use the atomic property + the helper
function implementing the legacy hook on top of atomic.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For some reason forgotten by history, we've been using a 1025-entry LUT
mode, and sparsely filling it with the 256-entry LUT we're handed.
Until we land support for the full atomic colour management properties,
this commit switches to using the 257-entry mode to fix colour mapping
with depth 30 framebuffers.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is what was done prior to the big refactor in kernel 3.8, and what
was done by xf86-video-nv. Experimentally, it seems like there's some
sort of issue with the high-res lut to be used there. Tested on G92.
This ends up mattering because fbcon/fbdev chooses the C8 fb format for
low-vram systems, which can occur with some IGP-based configurations
with little "stolen" vram.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's entirely possibly that the other r375 code is relevant to r370 too,
but I've not confirmed this, so I'll leave it where it is for now.
NVIDIA's copyright headers maintained, as it's still all their code.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
gcc-8 reports
drivers/gpu/drm/nouveau/nvkm/engine/pm/base.c: In function 'nvkm_perfmon_mthd':
include/linux/string.h:265:9: error: '__builtin_strncpy' specified bound 64 equals destination size [-Werror=stringop-truncation]
We need one less byte or call strlcpy() to make it a
nul-terminated string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The kbuild test bot complained about a new coccinelle warning nearby,
which sparked a discussion about the assignment to 'memory' inside of
the conditional expression. See Link below for the original post.
Fix the assignment to silence the coccinelle warning and also make the
code look a little nicer.
Link: https://lists.freedesktop.org/archives/nouveau/2017-November/029242.html
Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously, we relied on only running the hangcheck while somebody was
waiting on the GPU, in order to minimise the amount of time hangcheck
had to run. (If nobody was watching the GPU, nobody would notice if the
GPU wasn't responding -- eventually somebody would care and so kick
hangcheck into action.) However, this falls apart from around commit
4680816be3 ("drm/i915: Wait first for submission, before waiting for
request completion"), as not all waiters declare themselves to hangcheck
and so we could switch off hangcheck and miss GPU hangs even when
waiting under the struct_mutex.
If we enable hangcheck from the first request submission, and let it run
until the GPU is idle again, we forgo all the complexity involved with
only enabling around waiters. We just have to remember to be careful that
we do not declare a GPU hang when idly waiting for the next request to
be come ready, as we will run hangcheck continuously even when the
engines are stalled waiting for external events. This should be true
already as we should only be tracking requests submitted to hardware for
execution as an indicator that the engine is busy.
Fixes: 4680816be3 ("drm/i915: Wait first for submission, before waiting for request completion"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104840
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129144104.3921-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
(cherry picked from commit 889230489b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
