Measurements for one particular UFS controller + UFS device show a 25%
higher read bandwidth if the maximum data buffer size is increased from 512
KiB to 1 MiB. Hence increase the maximum size of the data buffer associated
with a single request from SCSI_DEFAULT_MAX_SECTORS (1024) * 512 bytes =
512 KiB to 1 MiB.
Notes:
- The maximum data buffer size supported by the UFSHCI specification
is 65535 * 256 KiB or about 16 GiB.
- The maximum data buffer size for READ(10) commands is 65535 logical
blocks. To transfer more than 65535 * 4096 bytes = 255 MiB with a single
SCSI command, the READ(16) command is required. Support for READ(16) is
optional in the UFS 3.1 and UFS 4.0 standards.
Link: https://lore.kernel.org/r/20220726225232.1362251-1-bvanassche@acm.org
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Tested-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes XDWRITEREAD support because it never fully worked when
it was added in the initial LIO merge and it's been fully broken since 2013
from commit a289008749 ("target: Add compare_and_write_post() completion
callback fall through").
The two issues above are:
1. XDWRITEREAD support was just never completed when LIO was merged. We
never did the DISABLE WRITE check and so we never write data out.
2. Since the commit above, we never complete the command. After we do the
XOR, we return from xdreadwrite_callback and that's it. We never send a
response for the command, so the command will always time out and fail.
Since this has been fully broken for almost nine years this patch just
removes emulated support.
Link: https://lore.kernel.org/r/20220726235339.14551-1-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RFC7143 states that Initiator decides what type of authentication to
use:
The initiator MUST continue with:
CHAP_N=<N> CHAP_R=<R>
or, if it requires target authentication, with:
CHAP_N=<N> CHAP_R=<R> CHAP_I=<I> CHAP_C=<C>
Allow one way authentication if mutual authentication is configured. That
passes some tests from Windows HLK for Mutual CHAP with iSNS.
Link: https://lore.kernel.org/r/20220718152555.17084-5-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable length SCSI commands are transferred over iSCSI via two CDB
buffers - in Basic Header Segment and in Additional Header Segment (AHS).
Since AHS is not supported yet, a target reads just BHS (48 byte) from TCP
and treats the remaining octets as a next new iSCSI PDU that causes
protocol errors.
Add support for the Extended CDB AHS type.
Link: https://lore.kernel.org/r/20220718152555.17084-2-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with Clang we encounter these warnings:
| drivers/target/iscsi/iscsi_target_login.c:719:24: error: format
| specifies type 'unsigned short' but the argument has type 'int'
| [-Werror,-Wformat] " from node: %s\n", atomic_read(&sess->nconn),
-
| drivers/target/iscsi/iscsi_target_login.c:767:12: error: format
| specifies type 'unsigned short' but the argument has type 'int'
| [-Werror,-Wformat] " %s\n", atomic_read(&sess->nconn),
-
| drivers/target/iscsi/iscsi_target.c:4365:12: error: format specifies
| type 'unsigned short' but the argument has type 'int' [-Werror,-Wformat]
| " %s\n", atomic_read(&sess->nconn)
For all warnings, the format specifier is '%hu' which describes an unsigned
short. The resulting type of atomic_read is an int. The proposed fix is to
listen to Clang and swap the format specifier.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Link: https://lore.kernel.org/r/20220718180421.49697-1-justinstitt@google.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS storage devices require bRefClkFreq attribute to be set to operate
correctly at high speed mode. The necessary value is determined by what the
SoC / board supports. The standard doesn't specify a method to query the
value, so the information needs to be fed in separately.
DT information feeds into setting up the clock framework, so platforms
using DT can get the UFS reference clock frequency from the clock
framework. A special node "ref_clk" from the clock array for the UFS
controller node is used as the source for the information.
On the platforms that do not use DT (e.g. Intel), the alternative mechanism
to feed the intended reference clock frequency is necessary. Specifying the
necessary information in DSD of the UFS controller ACPI node is an
alternative mechanism proposed in this patch. Those can be accessed via
firmware property facility in the kernel and in many ways simillar to
querying properties defined in DT.
This patch introduces a small helper function to query a predetermined ACPI
supplied property of the UFS controller, and uses it to attempt retrieving
reference clock value, unless that was already done by the clock
infrastructure.
Link: https://lore.kernel.org/r/20220715210230.1.I365d113d275117dee8fd055ce4fc7e6aebd0bce9@changeid
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Daniil Lunev <dlunev@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is some clean up necessary before returning. Smatch complains:
drivers/scsi/mpi3mr/mpi3mr_fw.c:4786 mpi3mr_soft_reset_handler()
warn: inconsistent returns '&mrioc->reset_mutex'.
Locked on : 4730
Unlocked on: 4786
Link: https://lore.kernel.org/r/YtVCEsxMU8buuMjP@kili
Fixes: f10af05732 ("scsi: mpi3mr: Resource Based Metering")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver to track cumulative pending large data size at the controller
level and at the throttle group level. When one of the values meet or
exceed the controller's firmware-determined high threshold value, then the
driver will divert future selective I/O to the firmware. Once both
controller level and at the throttle group level cumulative pending large
data size reach controller's firmware determined low threshold value, then
the driver will stop diverting I/Os to the firmware.
Link: https://lore.kernel.org/r/20220708195020.8323-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a SCSI device is removed while in active use, currently sg will
immediately return -ENODEV on any attempt to wait for active commands that
were sent before the removal. This is problematic for commands that use
SG_FLAG_DIRECT_IO since the data buffer may still be in use by the kernel
when userspace frees or reuses it after getting ENODEV, leading to
corrupted userspace memory (in the case of READ-type commands) or corrupted
data being sent to the device (in the case of WRITE-type commands). This
has been seen in practice when logging out of a iscsi_tcp session, where
the iSCSI driver may still be processing commands after the device has been
marked for removal.
Change the policy to allow userspace to wait for active sg commands even
when the device is being removed. Return -ENODEV only when there are no
more responses to read.
Link: https://lore.kernel.org/r/5ebea46f-fe83-2d0b-233d-d0dcb362dd0a@cybernetics.com
Cc: <stable@vger.kernel.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On some platforms, the current logic of relying on finding new packet
solely based on signature pattern can lead to driver reading stale
packets. Though this is a bug in those platforms, reduce such exposures by
limiting reading packets until the IN pointer.
Two module parameters are introduced:
ql2xrspq_follow_inptr:
When set, on newer adapters that has queue pointer shadowing, look for
response packets only until response queue in pointer.
When reset, response packets are read based on a signature pattern
logic (old way).
ql2xrspq_follow_inptr_legacy:
Like ql2xrspq_follow_inptr, but for those adapters where there is no
queue pointer shadowing.
Link: https://lore.kernel.org/r/20220713052045.10683-5-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow user to override the default driver timeout for controller ready.
There are some rare configurations which require the driver to wait longer
than the normal 3 minutes for the controller to complete its bootup
sequence and be ready to accept commands from the driver.
The module parameter is:
ctrl_ready_timeout= { 0 | 30-1800 }
and specifies the timeout in seconds for the driver to wait for controller
ready. The valid range is 0 or 30-1800. The default value is 0, which
causes the driver to use a timeout of 180 seconds (3 minutes).
Link: https://lore.kernel.org/r/165730607666.177165.9221211345284471213.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow SMP affinity to be changeable by disabling managed interrupts.
On distributions where the driver is enabled for multi-queue support the
driver utilizes kernel managed interrupts, which automatically distributes
interrupts to all available CPUs and assigns SMP affinity.
On most distributions, the affinity can not be changed by the user.
This change will allow managed interrupts to be disabled by the user via a
module parameter while still allowing multi-queue support to function
properly.
Use the module parameter disable_managed_interrupts=1
Link: https://lore.kernel.org/r/165730606638.177165.12846020942931640329.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a SOP READ and WRITE DMA flags for some requests.
This update corrects DMA direction issues with SCSI commands removed from
the controller's internal lookup table.
Currently, SCSI READ BLOCK LIMITS (0x5) was removed from the controller
lookup table and exposed a DMA direction flag issue.
SCSI READ BLOCK LIMITS was recently removed from our controller lookup
table so the controller uses the respective IU flag field to set the DMA
data direction. Since the DMA direction is incorrect the FW never completes
the request causing a hang.
Some SCSI commands which use SCSI READ BLOCK LIMITS
* sg_map
* mt -f /dev/stX status
After updating controller firmware, users may notice their tape units
failing. This patch resolves the issue.
Also, the AIO path DMA direction is correct.
The DMA direction flag is a day-one bug with no reported BZ.
Fixes: 6c223761eb ("smartpqi: initial commit of Microsemi smartpqi driver")
Link: https://lore.kernel.org/r/165730605618.177165.9054223644512926624.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fail all outstanding requests after a PCI linkdown.
Block access to device SCSI attributes during the following conditions:
"Cable pull" is called PQI_CTRL_SURPRISE_REMOVAL.
"PCIe Link Down" is called PQI_CTRL_GRACEFUL_REMOVAL.
Block access to device SCSI attributes during and in rare instances when
the controller goes offline.
Either outstanding requests or the access of SCSI attributes post linkdown
can lead to a hang.
Post linkdown, driver does not fail the outstanding requests leading to
long wait time before all the IOs eventually fail.
Also access of the SCSI attributes by host applications can lead to a
system hang.
Link: https://lore.kernel.org/r/165730603578.177165.4699352086827187263.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check the response code returned from the LUN reset task management
function and if it indicates the LUN is not valid, do not retry.
Reduce rescan worker delay to 5 seconds for the event handler only.
The removal of a drive from the OS could have been delayed up to 30 seconds
after being physically pulled.
The driver was retrying a LUN reset 3 times even though the return code
indiciated the LUN was no longer valid. There was a 10 second delay between
each retry. Additionally, the rescan worker was scheduled to run 10 seconds
after the driver received the event.
Link: https://lore.kernel.org/r/165730601025.177165.9416869335174437006.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
