- Use ioremap(), not phys_to_virt() for platform ROM, to fix video ROM
mapping with CONFIG_HIGHMEM (Mikel Rychliski)
- Add support for root bus sizing so we don't have to assume host bridge
windows are known a priori (Ivan Kokshaysky)
- Fix alpha Nautilus PCI setup, which has been broken since we started
enforcing window limits in resource allocation (Ivan Kokshaysky)
* pci/resource:
alpha: Fix nautilus PCI setup
PCI: Add support for root bus sizing
PCI: Use ioremap(), not phys_to_virt() for platform ROM
- Move _HPX type array from stack to static data (Colin Ian King)
- Avoid an ASMedia XHCI USB PME# defect; apparently it doesn't assert
PME# when USB3.0 devices are hotplugged in D0 (Kai-Heng Feng)
- Revert sysfs "rescan" file renames that broke an application (Kelsey
Skunberg)
* pci/misc:
PCI: sysfs: Revert "rescan" file renames
PCI: Avoid ASMedia XHCI USB PME# from D0 defect
PCI/ACPI: Move pcie_to_hpx3_type[] from stack to static data
- Disable in-band presence detection when possible (Alexandru Gagniuc)
- Poll for presence detect if in-band presence detection is disabled
(Alexandru Gagniuc)
- Add DMI table of systems that don't support in-band presence detection
(Stuart Hayes)
- Fix indefinite pciehp wait caused by race in handling sysfs requests
(Lukas Wunner)
- Fix pciehp MSI interrupt race that caused us to miss interrupts (Stuart
Hayes)
* pci/hotplug:
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: pciehp: Add DMI table for in-band presence detection disabled
PCI: pciehp: Wait for PDS if in-band presence is disabled
PCI: pciehp: Disable in-band presence detect when possible
- Update error status after reset_link() so we don't report "recovery
failed" when it in fact succeeded (Kuppuswamy Sathyanarayanan)
- Move DPC data into struct pci_dev instead of allocating a separate
struct dpc_dev (Bjorn Helgaas)
- Remove AER/DPC service dependency to simplify error recovery
(Kuppuswamy Sathyanarayanan)
- Return error recovery status for future use by EDR, which needs to tell
firmware whether recovery was successful (Kuppuswamy Sathyanarayanan)
- Cache DPC capability info in core since it's needed by EDR as well as
DPC driver (Kuppuswamy Sathyanarayanan)
- Add pci_aer_raw_clear_status() to allow EDR recovery path to clear AER
status even when OS doesn't own the AER capability (Kuppuswamy
Sathyanarayanan)
- Add Error Disconnect Recover (EDR) support, so firmware can use ACPI
notification to tell the OS that devices have been disconnected, e.g.,
via DPC, and that OS should attempt recovery (Kuppuswamy
Sathyanarayanan)
- Rename AER error status clearing interfaces to be more consistent
(Kuppuswamy Sathyanarayanan)
* pci/edr:
PCI/AER: Rationalize error status register clearing
PCI/DPC: Add Error Disconnect Recover (EDR) support
PCI/DPC: Expose dpc_process_error(), dpc_reset_link() for use by EDR
PCI/AER: Add pci_aer_raw_clear_status() to unconditionally clear Error Status
PCI/DPC: Cache DPC capabilities in pci_init_capabilities()
PCI/ERR: Return status of pcie_do_recovery()
PCI/ERR: Remove service dependency in pcie_do_recovery()
PCI/DPC: Move DPC data into struct pci_dev
PCI/ERR: Update error status after reset_link()
PCI/ERR: Combine pci_channel_io_frozen cases
Without this commit, a PCIe hotplug port can stop generating interrupts on
hotplug events, so device adds and removals will not be seen:
The pciehp interrupt handler pciehp_isr() reads the Slot Status register
and then writes back to it to clear the bits that caused the interrupt. If
a different interrupt event bit gets set between the read and the write,
pciehp_isr() returns without having cleared all of the interrupt event
bits. If this happens when the MSI isn't masked (which by default it isn't
in handle_edge_irq(), and which it will never be when MSI per-vector
masking is not supported), we won't get any more hotplug interrupts from
that device.
That is expected behavior, according to the PCIe Base Spec r5.0, section
6.7.3.4, "Software Notification of Hot-Plug Events".
Because the Presence Detect Changed and Data Link Layer State Changed event
bits can both get set at nearly the same time when a device is added or
removed, this is more likely to happen than it might seem. The issue was
found (and can be reproduced rather easily) by connecting and disconnecting
an NVMe storage device on at least one system model where the NVMe devices
were being connected to an AMD PCIe port (PCI device 0x1022/0x1483).
Fix the issue by modifying pciehp_isr() to loop back and re-read the Slot
Status register immediately after writing to it, until it sees that all of
the event status bits have been cleared.
[lukas: drop loop count limitation, write "events" instead of "status",
don't loop back in INTx and poll modes, tweak code comment & commit msg]
Link: https://lore.kernel.org/r/78b4ced5072bfe6e369d20e8b47c279b8c7af12e.1582121613.git.lukas@wunner.de
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
David Hoyer reports that powering pciehp slots up or down via sysfs may
hang: The call to wait_event() in pciehp_sysfs_enable_slot() and
_disable_slot() does not return because ctrl->ist_running remains true.
This flag, which was introduced by commit 157c1062fc ("PCI: pciehp: Avoid
returning prematurely from sysfs requests"), signifies that the IRQ thread
pciehp_ist() is running. It is set to true at the top of pciehp_ist() and
reset to false at the end. However there are two additional return
statements in pciehp_ist() before which the commit neglected to reset the
flag to false and wake up waiters for the flag.
That omission opens up the following race when powering up the slot:
* pciehp_ist() runs because a PCI_EXP_SLTSTA_PDC event was requested
by pciehp_sysfs_enable_slot()
* pciehp_ist() turns on slot power via the following call stack:
pciehp_handle_presence_or_link_change() -> pciehp_enable_slot() ->
__pciehp_enable_slot() -> board_added() -> pciehp_power_on_slot()
* after slot power is turned on, the link comes up, resulting in a
PCI_EXP_SLTSTA_DLLSC event
* the IRQ handler pciehp_isr() stores the event in ctrl->pending_events
and returns IRQ_WAKE_THREAD
* the IRQ thread is already woken (it's bringing up the slot), but the
genirq code remembers to re-run the IRQ thread after it has finished
(such that it can deal with the new event) by setting IRQTF_RUNTHREAD
via __handle_irq_event_percpu() -> __irq_wake_thread()
* the IRQ thread removes PCI_EXP_SLTSTA_DLLSC from ctrl->pending_events
via board_added() -> pciehp_check_link_status() in order to deal with
presence and link flaps per commit 6c35a1ac3d ("PCI: pciehp:
Tolerate initially unstable link")
* after pciehp_ist() has successfully brought up the slot, it resets
ctrl->ist_running to false and wakes up the sysfs requester
* the genirq code re-runs pciehp_ist(), which sets ctrl->ist_running
to true but then returns with IRQ_NONE because ctrl->pending_events
is empty
* pciehp_sysfs_enable_slot() is finally woken but notices that
ctrl->ist_running is true, hence continues waiting
The only way to get the hung task going again is to trigger a hotplug
event which brings down the slot, e.g. by yanking out the card.
The same race exists when powering down the slot because remove_board()
likewise clears link or presence changes in ctrl->pending_events per commit
3943af9d01 ("PCI: pciehp: Ignore Link State Changes after powering off a
slot") and thereby may cause a re-run of pciehp_ist() which returns with
IRQ_NONE without resetting ctrl->ist_running to false.
Fix by adding a goto label before the teardown steps at the end of
pciehp_ist() and jumping to that label from the two return statements which
currently neglect to reset the ctrl->ist_running flag.
Fixes: 157c1062fc ("PCI: pciehp: Avoid returning prematurely from sysfs requests")
Link: https://lore.kernel.org/r/cca1effa488065cb055120aa01b65719094bdcb5.1584530321.git.lukas@wunner.de
Reported-by: David Hoyer <David.Hoyer@netapp.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # v4.19+
In certain cases we should be able to enumerate IO and MEM ranges of all
PCI devices installed in the system, and then set respective host bridge
apertures basing on calculated size and alignment. Particularly when
firmware is broken and fails to assign bridge windows properly, like on
Alpha UP1500 platform.
Actually, almost everything is already in place, and required changes are
minimal:
- add "size_windows" flag to struct pci_host_bridge: when set, it
instructs __pci_bus_size_bridges() to continue with the root bus;
- in the __pci_bus_size_bridges() path: add checks for bus->self,
as it can legitimately be null for the root bus.
Link: https://lore.kernel.org/r/20200314194355.GA12510@mail.rc.ru
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some EFI systems, the video BIOS is provided by the EFI firmware. The
boot stub code stores the physical address of the ROM image in pdev->rom.
Currently we attempt to access this pointer using phys_to_virt(), which
doesn't work with CONFIG_HIGHMEM.
On these systems, attempting to load the radeon module on a x86_32 kernel
can result in the following:
BUG: unable to handle page fault for address: 3e8ed03c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2
Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS MP11.88Z.005C.B08.0707021221 07/02/07
EIP: radeon_get_bios+0x5ed/0xe50 [radeon]
Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06
EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000
ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206
CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0
Call Trace:
r520_init+0x26/0x240 [radeon]
radeon_device_init+0x533/0xa50 [radeon]
radeon_driver_load_kms+0x80/0x220 [radeon]
drm_dev_register+0xa7/0x180 [drm]
radeon_pci_probe+0x10f/0x1a0 [radeon]
pci_device_probe+0xd4/0x140
Fix the issue by updating all drivers which can access a platform provided
ROM. Instead of calling the helper function pci_platform_rom() which uses
phys_to_virt(), call ioremap() directly on the pdev->rom.
radeon_read_platform_bios() previously directly accessed an __iomem
pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().
pci_platform_rom() now has no remaining callers, so remove it.
Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.com
Signed-off-by: Mikel Rychliski <mikel@mikelr.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
When the UEFI/BIOS or bootloader has not initialised a PCIe device we would
get the following message:
kern.warning: pci 0000:00:01.0: ASPM: current common clock configuration is broken, reconfiguring
"warning" and "broken" are slightly misleading. On an embedded system it is
quite possible for the bootloader to avoid configuring PCIe devices if they
are not needed.
Downgrade the message to pci_info() and change "broken" to "inconsistent"
since we fix up the inconsistency in the code immediately following the
message (and emit an error if that fails).
Link: https://lore.kernel.org/r/20200323035530.11569-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Error Disconnect Recover (EDR) is a feature that allows ACPI firmware to
notify OSPM that a device has been disconnected due to an error condition
(ACPI v6.3, sec 5.6.6). OSPM advertises its support for EDR on PCI devices
via _OSC (see [1], sec 4.5.1, table 4-4). The OSPM EDR notify handler
should invalidate software state associated with disconnected devices and
may attempt to recover them. OSPM communicates the status of recovery to
the firmware via _OST (sec 6.3.5.2).
For PCIe, firmware may use Downstream Port Containment (DPC) to support
EDR. Per [1], sec 4.5.1, table 4-6, even if firmware has retained control
of DPC, OSPM may read/write DPC control and status registers during the EDR
notification processing window, i.e., from the time it receives an EDR
notification until it clears the DPC Trigger Status.
Note that per [1], sec 4.5.1 and 4.5.2.4,
1. If the OS supports EDR, it should advertise that to firmware by
setting OSC_PCI_EDR_SUPPORT in _OSC Support.
2. If the OS sets OSC_PCI_EXPRESS_DPC_CONTROL in _OSC Control to request
control of the DPC capability, it must also set OSC_PCI_EDR_SUPPORT in
_OSC Support.
Add an EDR notify handler to attempt recovery.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: squash add/enable patches into one]
Link: https://lore.kernel.org/r/90f91fe6d25c13f9d2255d2ce97ca15be307e1bb.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
If firmware controls DPC, it is generally responsible for managing the DPC
capability and events, and the OS should not access the DPC capability.
However, if firmware controls DPC and both the OS and the platform support
Error Disconnect Recover (EDR) notifications, the OS EDR notify handler is
responsible for recovery, and the notify handler may read/write the DPC
capability until it clears the DPC Trigger Status bit. See [1], sec 4.5.1,
table 4-6.
Expose some DPC error handling functions so they can be used by the EDR
notify handler.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/e9000bb15b3a4293e81d98bb29ead7c84a6393c9.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As per the DPC Enhancements ECN [1], sec 4.5.1, table 4-4, if the OS
supports Error Disconnect Recover (EDR), it must invalidate the software
state associated with child devices of the port without attempting to
access the child device hardware. In addition, if the OS supports DPC, it
must attempt to recover the child devices if the port implements the DPC
Capability. If the OS continues operation, the OS must inform the firmware
of the status of the recovery operation via the _OST method.
Return the result of pcie_do_recovery() so we can report it to firmware via
_OST.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/eb60ec89448769349c6722954ffbf2de163155b5.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we passed the PCIe service type parameter to pcie_do_recovery(),
where reset_link() looked up the underlying pci_port_service_driver and its
.reset_link() function pointer. Instead of using this roundabout way, we
can just pass the driver-specific .reset_link() callback function when
calling pcie_do_recovery() function.
This allows us to call pcie_do_recovery() from code that is not a PCIe port
service driver, e.g., Error Disconnect Recover (EDR) support.
Remove pcie_port_find_service() and pcie_port_service_driver.reset_link
since they are now unused.
Link: https://lore.kernel.org/r/60e02b87b526cdf2930400059d98704bf0a147d1.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit bdb5ac8577 ("PCI/ERR: Handle fatal error recovery") uses
reset_link() to recover from fatal errors. But during fatal error
recovery, if the initial value of error status is PCI_ERS_RESULT_DISCONNECT
or PCI_ERS_RESULT_NO_AER_DRIVER then even after successful recovery (using
reset_link()) pcie_do_recovery() will report the recovery result as
failure. Update the status of error after reset_link().
You can reproduce this issue by triggering a SW DPC using "DPC Software
Trigger" bit in "DPC Control Register". You should see recovery failed
dmesg log as below:
pcieport 0000:00:16.0: DPC: containment event, status:0x1f27 source:0x0000
pcieport 0000:00:16.0: DPC: software trigger detected
pci 0000:04:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:16.0: AER: device recovery failed
Fixes: bdb5ac8577 ("PCI/ERR: Handle fatal error recovery")
Link: https://lore.kernel.org/r/a255fcb3a3fdebcd90f84e08b555f1786eb8eba2.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
[bhelgaas: split pci_channel_io_frozen simplification to separate patch]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
The ASMedia USB XHCI Controller claims to support generating PME# while
in D0:
01:00.0 USB controller: ASMedia Technology Inc. Device 2142 (prog-if 30 [XHCI])
Subsystem: SUNIX Co., Ltd. Device 312b
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
However PME# only gets asserted when plugging USB 2.0 or USB 1.1 devices,
but not for USB 3.0 devices.
Remove PCI_PM_CAP_PME_D0 to avoid using PME under D0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205919
Link: https://lore.kernel.org/r/20191219192006.16270-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously some PCI speed strings came from pci_speed_string(), some came
from the PCIe-specific PCIE_SPEED2STR(), and some came from a PCIe-specific
switch statement. These methods were inconsistent:
pci_speed_string() PCIE_SPEED2STR() switch
------------------ ---------------- ------
33 MHz PCI
...
2.5 GT/s PCIe 2.5 GT/s 2.5 GT/s
5.0 GT/s PCIe 5 GT/s 5 GT/s
8.0 GT/s PCIe 8 GT/s 8 GT/s
16.0 GT/s PCIe 16 GT/s 16 GT/s
32.0 GT/s PCIe 32 GT/s 32 GT/s
Standardize on pci_speed_string() as the single source of these strings.
Note that this adds ".0" and "PCIe" to some messages, including sysfs
"max_link_speed" files, a brcmstb "link up" message, and the link status
dmesg logging, e.g.,
nvme 0000:01:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:01.1 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
I think it's better to standardize on a single version of the speed text.
Previously we had strings like this:
/sys/bus/pci/slots/0/cur_bus_speed: 8.0 GT/s PCIe
/sys/bus/pci/slots/0/max_bus_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8 GT/s
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8 GT/s
This changes the latter two to match the slots files:
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8.0 GT/s PCIe
Based-on-patch by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_speed_string() to return a text description of the supplied bus or
link speed. The slot code previously used the private
pci_bus_speed_strings[] array for this purpose, but adding this interface
will enable us to consolidate similar code elsewhere.
Export pcie_link_speed[] and pci_speed_string() so they can be used by
modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following was observed by Kar Hin Ong with RT patchset:
Backtrace:
irq 19: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 3329 Comm: irq/34-nipalk Tainted:4.14.87-rt49 #1
Hardware name: National Instruments NI PXIe-8880/NI PXIe-8880,
BIOS 2.1.5f1 01/09/2020
Call Trace:
<IRQ>
? dump_stack+0x46/0x5e
? __report_bad_irq+0x2e/0xb0
? note_interrupt+0x242/0x290
? nNIKAL100_memoryRead16+0x8/0x10 [nikal]
? handle_irq_event_percpu+0x55/0x70
? handle_irq_event+0x4f/0x80
? handle_fasteoi_irq+0x81/0x180
? handle_irq+0x1c/0x30
? do_IRQ+0x41/0xd0
? common_interrupt+0x84/0x84
</IRQ>
...
handlers:
[<ffffffffb3297200>] irq_default_primary_handler threaded
[<ffffffffb3669180>] usb_hcd_irq
Disabling IRQ #19
The problem being that this device is triggering boot interrupts
due to threaded interrupt handling and masking of the IO-APIC. These
boot interrupts are then forwarded on to the legacy PCH's PIRQ lines
where there is no handler present for the device.
Whenever a PCI device fires interrupt (INTx) to Pin 20 of IOAPIC 2
(GSI 44), the kernel receives two interrupts:
1. Interrupt from Pin 20 of IOAPIC 2 -> Expected
2. Interrupt from Pin 19 of IOAPIC 1 -> UNEXPECTED
Quirks for disabling boot interrupts (preferred) or rerouting the
handler exist but do not address these Xeon chipsets' mechanism:
https://lore.kernel.org/lkml/12131949181903-git-send-email-sassmann@suse.de/
Add a new mechanism via PCI CFG for those chipsets supporting CIPINTRC
register's dis_intx_rout2ich bit.
Link: https://lore.kernel.org/r/20200220192930.64820-2-sean.v.kelley@linux.intel.com
Reported-by: Kar Hin Ong <kar.hin.ong@ni.com>
Tested-by: Kar Hin Ong <kar.hin.ong@ni.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Some systems have in-band presence detection disabled for hot-plug PCI
slots but do not report this in the slot capabilities 2 (SLTCAP2) register.
On these systems, presence detect can become active well after the link is
reported to be active, which can cause the slots to be disabled after a
device is connected.
Add a DMI table to flag these systems as having in-band presence detect
disabled.
Link: https://lore.kernel.org/r/20191025190047.38130-4-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
When in-band presence detect is disabled, PDS may come up at any time or
not at all. PDS being low may indicate that the card is still mating, and
we could expect contact bounce to bring down the link as well.
It is reasonable to assume that most cards will mate in a hotplug slot in
about a second. Thus, when we know PDS only reflects out-of-band presence
detect, it's worthwhile to wait the extra second or so to make sure the
card is properly mated before loading the driver and to prevent the hotplug
code from disabling a device if the presence detect change goes active
after the device is enabled.
Link: https://lore.kernel.org/r/20191025190047.38130-3-stuart.w.hayes@gmail.com
[bhelgaas: use ctrl_info() instead of pci_info()]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
The presence detect state (PDS) is normally a logical OR of in-band and
out-of-band (OOB) presence detect. As of PCIe 4.0, there is the option to
disable in-band presence so that the PDS bit always reflects the state of
the out-of-band presence.
The recommendation of the PCIe spec is to disable in-band presence whenever
supported (PCIe r5.0, appendix I implementation note):
Due to architectural issues, the in-band (Physical-Layer-based) portion
of the PD mechanism is deprecated for use with async hot-plug. One issue
is that in-band PD as architected does not detect adapter removal during
certain LTSSM states, notably the L1 and Disabled States. Another issue
is that when both in-band and OOB PD are being used together, the
Presence Detect State bit and its associated interrupt mechanism always
reflect the logical OR of the inband and OOB PD states, and with some
hot-plug hardware configurations, it is important for software to detect
and respond to in-band and OOB PD events independently. If OOB PD is
being used and the associated DSP supports In-Band PD Disable, it is
recommended that the In-Band PD Disable bit be Set, and the Presence
Detect State bit and its associated interrupt mechanism be used
exclusively for OOB PD. As a substitute for in-band PD with async
hot-plug, the reference model uses either the DPC or the DLL Link Active
mechanism.
Link: https://lore.kernel.org/r/20191025190047.38130-2-stuart.w.hayes@gmail.com
[bhelgaas: move PCI_EXP_SLTCAP2 read earlier & print PCI_EXP_SLTCAP2_IBPD
value (suggested by Lukas)]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
