Commit 07bcab9394 ("ALSA: hda/realtek: Add support for HP Laptops")
breaks mute and micmute LEDs because it changed the LED quirk from
ALC285_FIXUP_HP_GPIO_LED to ALC245_FIXUP_HP_GPIO_LED, so change it back
here.
Also reorder the chain of quirks to ensure LED quirk is the last one
being applied.
Fixes: 07bcab9394 ("ALSA: hda/realtek: Add support for HP Laptops")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220317221134.566358-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Scarlett Gen 2/3 interfaces with internal mixers have a
"standalone" mode. When the interface is not connected to a USB host
and standalone mode is enabled, the interface will pass audio as
previously configured. This patch adds an ALSA control to allow
enabling/disabling that mode.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/cd88871c5e77abd5c23a4758a1f2ec9fd427fd69.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scarlett2_config_items[] contains the parameters for the configuration
items. The driver previously had two sets of configurations items; one
for devices with no mixer, and one for devices with a mixer. This
patch splits the latter into two (one set for Gen 2 devices and one
set for Gen 3 devices) in preparation for a new item (standalone)
which is present in both but with a different offset.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20969f9ea500684e978c87067fbdc7e73de1f6ed.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel HDMI LPE audio driver has its own mmap callback that mimics with
the noncached page attributes, but this is rather superfluous and can
be replaced with the standard helper, as the device is only for
playback and the write-cache should suffice.
This patch drops the own code and just uses the standard helper.
Link: https://lore.kernel.org/r/20220305083308.15718-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
Signed-off-by: Reza Jahanbakhshi <reza.jahanbakhshi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304212303.195949-1-reza.jahanbakhshi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AV/C deferred transaction was supported at a commit 00a7bb81c2 ("ALSA:
firewire-lib: Add support for deferred transaction") while 'deferrable'
flag can be uninitialized for non-control/notify AV/C transactions.
UBSAN reports it:
kernel: ================================================================================
kernel: UBSAN: invalid-load in /build/linux-aa0B4d/linux-5.15.0/sound/firewire/fcp.c:363:9
kernel: load of value 158 is not a valid value for type '_Bool'
kernel: CPU: 3 PID: 182227 Comm: irq/35-firewire Tainted: P OE 5.15.0-18-generic #18-Ubuntu
kernel: Hardware name: Gigabyte Technology Co., Ltd. AX370-Gaming 5/AX370-Gaming 5, BIOS F42b 08/01/2019
kernel: Call Trace:
kernel: <IRQ>
kernel: show_stack+0x52/0x58
kernel: dump_stack_lvl+0x4a/0x5f
kernel: dump_stack+0x10/0x12
kernel: ubsan_epilogue+0x9/0x45
kernel: __ubsan_handle_load_invalid_value.cold+0x44/0x49
kernel: fcp_response.part.0.cold+0x1a/0x2b [snd_firewire_lib]
kernel: fcp_response+0x28/0x30 [snd_firewire_lib]
kernel: fw_core_handle_request+0x230/0x3d0 [firewire_core]
kernel: handle_ar_packet+0x1d9/0x200 [firewire_ohci]
kernel: ? handle_ar_packet+0x1d9/0x200 [firewire_ohci]
kernel: ? transmit_complete_callback+0x9f/0x120 [firewire_core]
kernel: ar_context_tasklet+0xa8/0x2e0 [firewire_ohci]
kernel: tasklet_action_common.constprop.0+0xea/0xf0
kernel: tasklet_action+0x22/0x30
kernel: __do_softirq+0xd9/0x2e3
kernel: ? irq_finalize_oneshot.part.0+0xf0/0xf0
kernel: do_softirq+0x75/0xa0
kernel: </IRQ>
kernel: <TASK>
kernel: __local_bh_enable_ip+0x50/0x60
kernel: irq_forced_thread_fn+0x7e/0x90
kernel: irq_thread+0xba/0x190
kernel: ? irq_thread_fn+0x60/0x60
kernel: kthread+0x11e/0x140
kernel: ? irq_thread_check_affinity+0xf0/0xf0
kernel: ? set_kthread_struct+0x50/0x50
kernel: ret_from_fork+0x22/0x30
kernel: </TASK>
kernel: ================================================================================
This commit fixes the bug. The bug has no disadvantage for the non-
control/notify AV/C transactions since the flag has an effect for AV/C
response with INTERIM (0x0f) status which is not used for the transactions
in AV/C general specification.
Fixes: 00a7bb81c2 ("ALSA: firewire-lib: Add support for deferred transaction")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220304125647.78430-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable bytes is being assigned a value that is never read, it
is being re-assigned inside a following if block. The assignment is
redundant and can be removed.
Cleans up clang scan build warning:
sound/pci/echoaudio/midi.c:211:9: warning: Although the value stored
to 'bytes' is used in the enclosing expression, the value is never
actually read from 'bytes' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220302170728.1094633-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initializing the static variable to 0 causes the following error
when exec checkpatch:
ERROR: do not initialise statics to 0
FILE: sound/sound_core.c:142:
static int preclaim_oss = 0;
In addition, considering the following way of writing
139: #ifdef config_sound_oss_core_preclaim
140: Static int preclaim_oss = 1;
141: #ELSE
142: Static int preclaim_oss = 0;
143: #ENDIF
We can optimize it by IS_ENABLED(CONFIG_SOUND_OSS_CORE_PRECLAIM),
so modified it to
static int preclaim_oss = IS_ENABLED(CONFIG_SOUND_OSS_CORE_PRECLAIM);
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220228050253.1649-1-tangmeng@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220225111929.17194-1-tangmeng@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v5.17
A few more fixes for v5.17, one followup to the bounds checking fixes
handling controls which support negative values internally and a driver
specific one.
Update binding document for HDA support on Tegra234 chip.
Tegra234 has max of 2 clocks and 2 resets which requires to add
minItems and maxItems for clocks and resets as Tegra chips can
now have minimum of 2 and maximum of 3 clocks and reset support.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-6-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra234 chip scratch register communication between audio
and hdmi driver differs slightly in the way it triggers the
interrupt compared to legacy chips. Interrupt is triggered
by writing non-zero values to verb 0xF80 instead of 31st bit
of scratch register.
DP MST support changed the NID to be used for scratch register
read/write from audio function group NID to Converter widget NID.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-4-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GCAP register on Tegra234 implies no Input Streams(ISS)
supported, but the HW output stream descriptor programming
should start with offset 0x20*4 from base stream descriptor
address. This will be a problem while calculating the offset
for output stream descriptor which will be considering input
stream also. So here output stream starts with offset 0 which
is wrong as HW register for output stream offset starts with 4.
So hardcode the input stream numbers to 4 to avoid the issue
in offset calculation.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-3-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add hda driver support for the Tegra234 chip. The hdacodec
on this chip now supports DP MST feature, HDA block contains
azalia controller and one hda-codec instance by supporting
4 independent output streams over DP MST mode. There is no
input stream support.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-2-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With few changes, snd_hda_codec_register() and its
unregister-counterpart can be re-used by ASoC drivers. While at it,
provide kernel doc for the exposed functions.
Due to ALSA-device vs ASoC-component organization differences, new
'snddev_managed' argument is specified allowing for better control over
codec registration process.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220214101404.4074026-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement HDA keep alive (KAE) support for Intel display codecs. When no
audio stream is active, the display codec will provide a continuous clock
and a valid but silent audio stream to any connected HDMI/DP receiver.
Without this, upon starting a new playback stream, initial samples may be
lost as many receivers require time to initialize for new clock.
This is a new feature in Intel AlderLake-P display codec implementation
and replaces the Intel i915 silent-stream extension that has been used
on older hardware. Main benefit of the new method is that codec no longer
needs to be kept in D0 power state.
This patch depends on commit 112a87c48e ("drm/i915/display: program
audio CDCLK-TS for keepalives").
[ a minor coding-style fix by tiwai ]
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Jyri Sarha <jyri.sarha@intel.com>
Link: https://lore.kernel.org/r/20220216172405.3994959-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the following error messages are seen during boot:
asoc-simple-card sound: control 2:0:0:SPDIF Switch:0 is already present
cs4265 1-004f: ASoC: failed to add widget SPDIF dapm kcontrol SPDIF Switch: -16
Quoting Mark Brown:
"The driver is just plain buggy, it defines both a regular SPIDF Switch
control and a SND_SOC_DAPM_SWITCH() called SPDIF both of which will
create an identically named control, it can never have loaded without
error. One or both of those has to be renamed or they need to be
merged into one thing."
Fix the duplicated control name by combining the two SPDIF controls here
and move the register bits onto the DAPM widget and have DAPM control them.
Fixes: f853d6b3ba ("ASoC: cs4265: Add a S/PDIF enable switch")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220215120514.1760628-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This branch contains 5.17-rc1 + the SPI tree's spi-acpi-helpers tag +
the other patches from the "[PATCH v6 0/9] Support Spi in
i2c-multi-instantiate driver" series.
ASoC: Fixes for v5.18
More fixes that have arrived in the past few -rcs, plus a MAINTAINERS
update. The biggest update here is the fix for control change
notifications in ASoC generic controls found by mixer-test.
The recently introduced coef_mutex for Realtek codec seems causing a
deadlock when the relevant code is invoked from the power-off state;
then the HD-audio core tries to power-up internally, and this kicks
off the codec runtime PM code that tries to take the same coef_mutex.
In order to avoid the deadlock, do the temporary power up/down around
the coef_mutex acquisition and release. This assures that the
power-up sequence runs before the mutex, hence no re-entrance will
happen.
Fixes: b837a9f5ab ("ALSA: hda: realtek: Fix race at concurrent COEF updates")
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220214132838.4db10fca@schienar
Link: https://lore.kernel.org/r/20220214130410.21230-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default mixer resume code treats the errors at restoring the
modified mixer items as a fatal error, and it returns back to the
caller. This ends up in the resume failure, and the device will be
come unavailable, although basically those errors are intermittent and
can be safely ignored.
The problem itself has been present from the beginning, but it didn't
hit usually because the code tries to resume only the modified items.
But now with the recent commit to forcibly initialize each item at the
probe time, the problem surfaced more often, hence it appears as a
regression.
This patch fixes the regression simply by ignoring the errors at
resume.
Fixes: b96681bd58 ("ALSA: usb-audio: Initialize every feature unit once at probe time")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215561
Link: https://lore.kernel.org/r/20220214125711.20531-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 83b7dcbc51 introduced a generic
implicit feedback parser, which fails to execute for M-Audio FastTrack
Ultra sound cards. The issue is with the ENDPOINT_SYNCTYPE check in
add_generic_implicit_fb() where the SYNCTYPE is ADAPTIVE instead of ASYNC.
The reason is that the sync type of the FastTrack output endpoints are
set to adaptive in the quirks table since commit
65f04443c9.
Fixes: 83b7dcbc51 ("ALSA: usb-audio: Add generic implicit fb parsing")
Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220211224913.20683-2-matteomartelli3@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When parsing the compressed stream the whole buffer descriptor is
now read in a single cs_dsp_coeff_read_ctrl; on older firmwares
this descriptor is just 4 bytes but on more modern firmwares it is
24 bytes. The current code reads the full 24 bytes regardless, this
was working but reading junk for the last 20 bytes. However commit
f444da38ac ("firmware: cs_dsp: Add offset to cs_dsp read/write")
added a size check into cs_dsp_coeff_read_ctrl, causing the older
firmwares to now return an error.
Update the code to only read the amount of data appropriate for
the firmware loaded.
Fixes: 04ae085967 ("ASoC: wm_adsp: Switch to using wm_coeff_read_ctrl for compressed buffers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220210172053.22782-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit da0363f7bf ("ASoC: qcom: Fix for DMA interrupt clear reg
overwriting") we changed regmap_write() to regmap_update_bits() so that
we can avoid overwriting bits that we didn't intend to modify.
Unfortunately this change breaks the case where a register is writable
but not readable, which is exactly how the HDMI irq clear register is
designed (grep around LPASS_HDMITX_APP_IRQCLEAR_REG to see how it's
write only). That's because regmap_update_bits() tries to read the
register from the hardware and if it isn't readable it looks in the
regmap cache to see what was written there last time to compare against
what we want to write there. Eventually, we're unable to modify this
register at all because the bits that we're trying to set are already
set in the cache.
This is doubly bad for the irq clear register because you have to write
the bit to clear an interrupt. Given the irq is level triggered, we see
an interrupt storm upon plugging in an HDMI cable and starting audio
playback. The irq storm is so great that performance degrades
significantly, leading to CPU soft lockups.
Fix it by using regmap_write_bits() so that we really do write the bits
in the clear register that we want to. This brings the number of irqs
handled by lpass_dma_interrupt_handler() down from ~150k/sec to ~10/sec.
Fixes: da0363f7bf ("ASoC: qcom: Fix for DMA interrupt clear reg overwriting")
Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220209232520.4017634-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ca0106 driver code uses too generic names for its register definitions
such as PTR, DATA, IPR, etc, which may eventually conflict with other
code. This patch renames (some of) those register definitions with
CA0106_ prefix to avoid the conflicts.
Link: https://lore.kernel.org/r/20220210124227.11272-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
