Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure for CW1200 WLAN chip
ARM: ux500: configure in sensors
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixing uart-rx pull settings and a copy'n'paste error in a smp message
* tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: fix copy'n'paste error in smp error messages
ARM: rockchip: rk3188: enable pull-ups on UART RX pins
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The i.MX fixes for 3.15:
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: i.MX6: ipu_di_sel clocks can set parent rates
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
ARM: dts: imx: add required #clock-cells for fixed-clock
ARM: dts: vybrid: drop address and size cells from GIC node
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
ARM: dts: imx53: fix apparent copy/paste error
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
ARM: dts: imx6: edmqmx6: add second STMPE
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
ARM: imx6q-clk: parent lvds_gate from lvds_sel
ARM: dts: imx: drop invalid size and address cells properties
ARM: dts: mx5: fix wrong stmpe-ts bindings
ARM: dts: imx53-m53evk: Fix memory region description
ARM: dts: imx53-qsb-common: Fix memory region description
ARM: dts: imx6: add PCIe interrupt mapping properties
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu DT fixes-non-critical (for v3.15-rc1)
- kirkwood
- add some missing vendor prefixes to keep checkpatch happy
- mvebu
- add clock ref to mdio node on 370/XP/38x
* tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x
ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP
ARM: Kirkwood: DT: Add missing vendor prefix
ARM: Kirkwood: Fix Atmel vendor prefix
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit a7cbe92cef ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few things were out of order:
- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
list sorted
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In commit ddb902cc34 (ARM: centralize common multi-platform kconfig
options), CLKSRC_OF was removed from some platforms, but not added to
ARCH_MULTIPLATFORM. Fix this.
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I get a build warning because spear_clocksource_init() calls
clocksource_mmio_init(), but it doesn't have an __init annotation.
Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
hx4700 needs the same fix as in
9705e74671
"ARM: pxa: fix various compilation problems"
Fix build errors. Initial one is:
/linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error:
'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function)
| #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.
Without this patch we can get the following error:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018)
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: tony Lindgren <tony@atomide.com>
BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit a70143 (drivers: phy: usb3/pipe3: Adapt pipe3 driver to Generic PHY
Framework) moved phy-omap-usb3 driver in drivers/usb/phy to drivers/phy and
also renamed the file to phy-ti-pipe3. It also renamed the config from
OMAP_USB3 to TI_PIPE3 in Kconfig. However the config name was not changed in
omap2plus_defconfig. Fixed it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739faba ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not try to initialize display for DT boot, since omapdss
is now initialized via Device Tree. Without this patch the
display subsystem does not properly come up.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The error emitted when mapping the pmu failed, wrongly mentions the sram.
Reported-by: Kent Borg <kentborg@borg.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.
Therefore change the rx-pin settings accordingly.
This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.
Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CW1200 WLAN chip driver had been in the kernel for a while,
we only need to activate it for the Ux500 properly. The latter
require some elaborative work, but in the meantime, let's make
sure we atleast compile it in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables the STMicroelectronics MEMS sensors for accelerometer,
gyroscope, magnetometer and pressure that are mounted on the Ux500
models.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since there are SD-card support in u300, it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are both (e)MMC/SD-card support in ux500, thus it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
c7a507eea1
(ASoC: fsi: fixup SND_SOC_DAIFMT_CBx_CFx flags)
exchanged sound flags, but armadillo800eva flags needs IB_NF.
The recorded sound will be noise without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
e150828940
(ASoC: rcar: fixup SND_SOC_DAIFMT_CBx_CFx flags)
corrected SND_SOC_DAIFMT_CBx_CFx definition.
But then, Lager board was maintenanced other branch.
This patch correct SND_SOC_DAIFMT_CBx_CFx flag for lager
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:
m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)
In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit (655b43c staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
