The current implementation of the async flip wm0/ddb optimization
does not work at all. The biggest problem is that we skip the
whole intel_pipe_update_{start,end}() dance and thus never actually
complete the commit that is trying to do the wm/ddb change.
To fix this we need to move the do_async_flip flag to the crtc
state since we handle commits per-pipe, not per-plane.
Also since all planes can now be included in the first/last
"async flip" (which gets converted to a sync flip to do the
wm/ddb mangling) we need to be more careful when checking if
the plane state is async flip comptatible. Only planes doing
the async flip should be checked and other planes are perfectly
fine not adhereing to any async flip related limitations.
However for subsequent commits which are actually going do the
async flip in hardware we want to make sure no other planes
are in the state. That should never happen assuming we did our
job correctly, so we'll toss in a WARN to make sure we catch
any bugs here.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be4 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Since the async flip state check is done very late and
thus it can see potentially all the planes in the state
(due to the wm/ddb optimization) we need to move the
"can the requested plane do async flips at all?" check
much earlier. For this purpose we introduce
intel_async_flip_check_uapi() that gets called early during
the atomic check.
And for good measure we'll throw in a couple of basic checks:
- is the crtc active?
- was a modeset flagged?
- is+was the plane enabled?
Though atm all of those should be guaranteed by the fact
that the async flip can only be requested through the legacy
page flip ioctl.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be4 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Some users are suffering with PSR2 issues that are under debug or
issues that were root caused to panel firmware bugs, to make life of
those users easier here adding a option to disable PSR2 with kernel
parameters so they can still benefit from PSR1 power savings.
Using the same enable_psr that is current used to turn the whole
feature on or off and allowing user to select up to what PSR version
it should enable.
Right now users only set this parameter to 0 when they want to disable
PSR1 and PSR2 or don't add it at all leaving it to per-chip behavior
so it should not cause a bad impact on users.
v2:
- changing enable_psr values (Ville and Rodrigo)
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/4951
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224202523.993560-1-jose.souza@intel.com
Currently we are observing occasional screen flickering when
PSR2 selective fetch is enabled. More specifically glitch seems
to happen on full frame update when cursor moves to coords
x = -1 or y = -1.
According to Bspec SF Single full frame should not be set if
SF Partial Frame Enable is not set. This happened to be true for
ADLP as PSR2_MAN_TRK_CTL_ENABLE is always set and for ADL_P it's
actually "SF Partial Frame Enable" (Bit 31).
Setting "SF Partial Frame Enable" bit also on full update seems to
fix screen flickering.
Also make code more clear by setting PSR2_MAN_TRK_CTL_ENABLE
only if not on ADL_P. Bit 31 has different meaning in ADL_P.
Bspec: 49274
v2: Fix Mihai Harpau email address
v3: Modify commit message and remove unnecessary comment
Tested-by: Lyude Paul <lyude@redhat.com>
Fixes: 7f6002e580 ("drm/i915/display: Enable PSR2 selective fetch by default")
Reported-by: Lyude Paul <lyude@redhat.com>
Cc: Mihai Harpau <mharpau@gmail.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/5077
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225070228.855138-1-jouni.hogander@intel.com
To catch up with recent rounds of pull requests
and get some drm-misc dependencies so we can merge
linux/string_helpers related changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Commit d5ce34da31
("drm/i915: Add state verification for the TypeC port mode")
added a verification to the TypeC AUX power well enable()/disable()
hooks to check if the TypeC port related to this power well is properly
locked. If the disabling happens asynchronously the verification is
skipped, since in this case the port is unlocked. The detection of
asnychronous disabling doesn't work as intended though, since the power
well's reference count is always 0 when its disable() hook is called
(and since there won't be any domain reference held for this power well
either, the verification is always skipped); remove the verification
from the disable() hook for now. In the power well's enable() hook the
power well's reference will be always >0 and there won't be any
asynchronous disabling pending for it, so we can drop the async refcount
check from there.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222165137.1004194-4-imre.deak@intel.com
Instead of open-coding the call of the power wells' enable()/disable()
hooks use the corresponding helper functions. This will also ensure that
the power well's cached-enable state is always up-to-date. Luckily the
lack of this updating hasn't been a problem, since the state either
didn't change (in intel_display_power_set_target_dc_state()), or got
updated subsequently (for vlv_cmnlane_wa(), in the following
intel_power_domains_sync_hw()).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222165137.1004194-3-imre.deak@intel.com
The POWER_DOMAIN_TRANSCODER() macro depends on the
POWER_DOMAIN_TRANSCODER_A/B .. DSI_A/C enum values to be consecutive,
move POWER_DOMAIN_TRANSCODER_VDSC_PW2 after these to ensure this. The
wrong order didn't cause a problem, since the DSI_A/C domains are in
always-on power wells on all relevant platforms. The same power well
ends up being enabled/disabled when the VDSC_PW2 domain is selected
incorrectly.
While at it add a code comment about enum values that need to stay
consecutive.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222165137.1004194-2-imre.deak@intel.com
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
Pull dma-mapping fix from Christoph Hellwig:
- fix a swiotlb info leak (Halil Pasic)
* tag 'dma-mapping-5.17-1' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix info leak with DMA_FROM_DEVICE
Pull pin control fixes from Linus Walleij:
- Fix some drive strength and pull-up code in the K210 driver.
- Add the Alder Lake-M ACPI ID so it starts to work properly.
- Use a static name for the StarFive GPIO irq_chip, forestalling an
upcoming fixes series from Marc Zyngier.
- Fix an ages old bug in the Tegra 186 driver where we were indexing at
random into struct and being lucky getting the right member.
* tag 'pinctrl-v5-17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: tegra186: Fix chip_data type confusion
pinctrl: starfive: Use a static name for the GPIO irq_chip
pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
pinctrl: k210: Fix bias-pull-up
pinctrl: fix loop in k210_pinconf_get_drive()
Pull tracing fixes from Steven Rostedt:
- rtla (Real-Time Linux Analysis tool):
- fix typo in man page
- Update API -e to -E before it is released
- Error message fix and memory leak fix
- Partially uninline trace event soft disable to shrink text
- Fix function graph start up test
- Have triggers affect the trace instance they are in and not top level
- Have osnoise sleep in the units it says it uses
- Remove unused ftrace stub function
- Remove event probe redundant info from event in the buffer
- Fix group ownership setting in tracefs
- Ensure trace buffer is minimum size to prevent crashes
* tag 'trace-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rtla/osnoise: Fix error message when failing to enable trace instance
rtla/osnoise: Free params at the exit
rtla/hist: Make -E the short version of --entries
tracing: Fix selftest config check for function graph start up test
tracefs: Set the group ownership in apply_options() not parse_options()
tracing/osnoise: Make osnoise_main to sleep for microseconds
ftrace: Remove unused ftrace_startup_enable() stub
tracing: Ensure trace buffer is at least 4096 bytes large
tracing: Uninline trace_trigger_soft_disabled() partly
eprobes: Remove redundant event type information
tracing: Have traceon and traceoff trigger honor the instance
tracing: Dump stacktrace trigger to the corresponding instance
rtla: Fix systme -> system typo on man page
Pull memblock fix from Mike Rapoport:
"Use kfree() to release kmalloced memblock regions
memblock.{reserved,memory}.regions may be allocated using kmalloc()
in memblock_double_array(). Use kfree() to release these kmalloced
regions"
* tag 'fixes-2022-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: use kfree() to release kmalloced memblock regions
Merge misc fixes from Andrew Morton:
"12 patches.
Subsystems affected by this patch series: MAINTAINERS, mailmap, memfd,
and mm (hugetlb, kasan, hugetlbfs, pagemap, selftests, memcg, and
slab)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
selftests/memfd: clean up mapping in mfd_fail_write
mailmap: update Roman Gushchin's email
MAINTAINERS, SLAB: add Roman as reviewer, git tree
MAINTAINERS: add Shakeel as a memcg co-maintainer
MAINTAINERS: remove Vladimir from memcg maintainers
MAINTAINERS: add Roman as a memcg co-maintainer
selftest/vm: fix map_fixed_noreplace test failure
mm: fix use-after-free bug when mm->mmap is reused after being freed
hugetlbfs: fix a truncation issue in hugepages parameter
kasan: test: prevent cache merging in kmem_cache_double_destroy
mm/hugetlb: fix kernel crash with hugetlb mremap
MAINTAINERS: add sysctl-next git tree
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for the K210 sdcard defconfig, to avoid using a
fixed delay for the root FS
- A fix to make sure there's a proper call frame for
trace_hardirqs_{on,off}().
* tag 'riscv-for-linus-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix oops caused by irqsoff latency tracer
riscv: fix nommu_k210_sdcard_defconfig
Pull xfs fixes from Darrick Wong:
"Nothing exciting, just more fixes for not returning sync_filesystem
error values (and eliding it when it's not necessary).
Summary:
- Only call sync_filesystem when we're remounting the filesystem
readonly readonly, and actually check its return value"
* tag 'xfs-5.17-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: only bother with sync_filesystem during readonly remount
Running the memfd script ./run_hugetlbfs_test.sh will often end in error
as follows:
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
memfd-hugetlb: SEAL-SHRINK
fallocate(ALLOC) failed: No space left on device
./run_hugetlbfs_test.sh: line 60: 166855 Aborted (core dumped) ./memfd_test hugetlbfs
opening: ./mnt/memfd
fuse: DONE
If no hugetlb pages have been preallocated, run_hugetlbfs_test.sh will
allocate 'just enough' pages to run the test. In the SEAL-FUTURE-WRITE
test the mfd_fail_write routine maps the file, but does not unmap. As a
result, two hugetlb pages remain reserved for the mapping. When the
fallocate call in the SEAL-SHRINK test attempts allocate all hugetlb
pages, it is short by the two reserved pages.
Fix by making sure to unmap in mfd_fail_write.
Link: https://lkml.kernel.org/r/20220219004340.56478-1-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
