Add DTS for EdgeRouter Lite that is usable as is without any "pruning"
with APPENDED_DTB.
Compared to builtin generic DTB, we can avoid errors and delays from
probing non-existent I2C devices.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
common place. We already have bcm47xx_nvram in firmware path and SPROM
should fit there as well.
This driver is responsible for parsing SoC configuration data into a
struct shared between ssb and bcma buses.
This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0
(ARCH_BCM_5301X).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was calling flush_cache_all() which is a no-op since a long time anyway
and which was overkill in the old days when it was actually doing something
because only the D-cache needs to be flushed, never the I-cache, never
the S-cache. Since however highmem on MIPS is still only supported on
processors that don't suffer from cache aliases, we could turn
flush_cache_kmaps() into a no-op - but for paranoia's sake we rather make
it BUG_ON(cpu_has_dc_aliases()).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's probably a good idea to flush caches before reset and by the time
this code was written flush_cache_all did actually still do something.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Flushing caches is probably sensible on reset but flush_cache_all has been
a no-op for a very long time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A couple of netlogic assembly files define CP0_EBASE to $15, the same as
CP0_PRID in mipsregs.h, and use it for accessing both CP0_PRId and
CP0_EBase registers. However commit 609cf6f229 ("MIPS: CPS: Early
debug using an ns16550-compatible UART") added a different definition of
CP0_EBASE to mipsregs.h, which included a register select of 1. This
causes harmless build warnings like the following:
arch/mips/netlogic/common/reset.S:53:0: warning: "CP0_EBASE" redefined
#define CP0_EBASE $15
^
In file included from arch/mips/netlogic/common/reset.S:41:0:
./arch/mips/include/asm/mipsregs.h:63:0: note: this is the location of the previous definition
#define CP0_EBASE $15, 1
^
Update the code to use the definitions from mipsregs.h for accessing
both registers.
Fixes: 609cf6f229 ("MIPS: CPS: Early debug using an ns16550-compatible UART")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update the recent changes to set_pte() that were added in 46011e6ea3
to handle R10000_LLSC_WAR, and format the assembly to match other areas
of the MIPS tree using the same WAR.
This also incorporates a patch recently sent in my Markos Chandras,
"Remove local LL/SC preprocessor variants", so that patch doesn't need
to be applied if this one is accepted.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Fixes: 46011e6ea3 ("MIPS: Make set_pte() SMP safe.)
Cc: David Daney <david.daney@cavium.com>
Cc: Linux/MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/11103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Building an MSA capable kernel with a toolchain that supports MSA
produces warnings such as this:
arch/mips/kernel/r4k_fpu.S:229: Warning: the `msa' extension requires 64-bit FPRs
This is due to ".set msa" without ".set fp=64" in the non doubleword MSA
load/store macros, since MSA requires the 64-bit FPU registers (FR=1).
Add the missing fp=64 in these macros to silence the warnings.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13063/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When lockdep is enabled on a 64-bit kernel the FPR offset into the
thread structure exceeds the maximum range of the MSA ld.d/st.d
instructions. For example THREAD_FPR31 = 4644 (instead of 2448), while
the signed immediate field is only 10 bits with an implicit multiply by
8, giving a maximum offset of 511*8 = 4088.
This isn't a problem when the toolchain doesn't support MSA as the
ld_*/st_* macros perform the addition separately into $1 with [d]addui
which has a 16bit signed immediate field.
Fix the case where the toolchain does support MSA by doing a single
addition of THREAD_FPR0 into $1 with [d]addui, and doing the ld_*/st_*
relative to that.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13064/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:
arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'
Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.3.x+
Patchwork: https://patchwork.linux-mips.org/patch/13061/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Error recovery pointers for fixups was improperly set as ".word"
which is unsuitable for MIPS64.
Replaced by STR(PTR)
[ralf@linux-mips.org: Apply changes as requested in the review process.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: b0a668fb20 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator for MIPS R6")
Cc: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/9911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is still necessary to handle icache coherency in flush_cache_range()
and copy_to_user_page() when the icache fills from the dcache, even
though the dcache does not need to be written back. However when this
handling was added in commit 2eaa7ec286 ("[MIPS] Handle I-cache
coherency in flush_cache_range()"), it did not do any icache flushing
when it fills from dcache.
Therefore fix r4k_flush_cache_range() to run
local_r4k_flush_cache_range() without taking into account whether icache
fills from dcache, so that the icache coherency gets handled. Checks are
also added in local_r4k_flush_cache_range() so that the dcache blast
doesn't take place when icache fills from dcache.
A test to mmap a page PROT_READ|PROT_WRITE, modify code in it, and
mprotect it to VM_READ|VM_EXEC (similar to case described in above
commit) can hit this case quite easily to verify the fix.
A similar check was added in commit f8829caee3 ("[MIPS] Fix aliasing
bug in copy_to_user_page / copy_from_user_page"), so also fix
copy_to_user_page() similarly, to call flush_cache_page() without taking
into account whether icache fills from dcache, since flush_cache_page()
already takes that into account to avoid performing a dcache flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HARDWARE_WATCHPOINTS isn't being enabled for CPU_MIPSR6, even though it
has an identical hardware watchpoint interface to CPU_MIPSR2, which
prevents ptrace watchpoints from being loaded when executing a ptraced
process even though the watchpoints are described in /proc/cpuinfo.
Enable HARDWARE_WATCHPOINTS for CPU_MIPSR6 too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
