The TI k3-j721s2 platform does not allow us to use uncached memory
(which is what the driver currently does) without disabling cache snooping
on the AXI ACE-Lite interface, which would be too much of a performance
hit.
Given the platform is dma-coherent, we can simply force all
device-accessible memory allocations through the CPU cache. In fact, this
can be done whenever the dma_coherent attribute is present.
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-15-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Extend interrupt handling logic to check for safety event IRQs, then clear
and handle them in the IRQ handler thread.
Safety events need to be checked and cleared with a different set of GPU
registers than those the IRQ handler has been using so far.
Only two safety events need to be handled on the host: FW fault (ECC error
correction or detection) and device watchdog timeout. Handling right now
simply consists of clearing any error and logging the event. If either of
these events results in an unrecoverable GPU or FW, the driver will
eventually attempt to recover from it e.g. via pvr_power_reset().
Note that Rogue GPUs may send interrupts to the host for all types of
safety events, not just the two above. For events not handled by the host,
clearing the associated interrupt is sufficient.
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-7-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Pass IRQF_ONESHOT flag to request_threaded_irq(), so that interrupts will
be masked by the kernel until the end of the threaded IRQ handler. Since
the calls to pvr_fw_irq_enable() and pvr_fw_irq_disable() are now
redundant, remove them.
Interrupts to the host from the soon-to-be-added RISC-V firmware
processors cannot be masked in hardware. This change allows us to continue
using the threaded handler in GPUs with a RISC-V firmware.
For simplicity, the same approach is taken for all firmware processors.
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-6-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
The first supported GPU only used a single power domain so this was
automatically handled by the device runtime.
In order to support multiple power domains, they must be enumerated from
devicetree and linked to both the GPU device and each other to ensure
correct power sequencing at start time.
For all Imagination Rogue GPUs, power domains are named "a", "b", etc. and
the sequence A->B->... is always valid for startup with the reverse true
for shutdown. Note this is not always the *only* valid sequence, but it's
simple and does not require special-casing for different GPU power
topologies.
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-5-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Follow-on from the companion dt-bindings change ("dt-bindings: gpu: img:
More explicit compatible strings"), deprecating "img,img-axe" in favour of
the more explicit combination of "img,img-rogue" and "img,img-axe-1-16m".
Since all relevant details are interrogated from the device at runtime,
we can match on the generic "img,img-rogue" and avoid adding more entries
with NULL data members (barring hardware quirks).
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-4-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
The first compatible strings added for the AXE-1-16M are not sufficient to
accurately describe all the IMG Rogue GPUs. The current "img,img-axe"
string refers to the entire family of Series AXE GPUs, but this is
primarily a marketing term and does not denote a level of hardware
similarity any greater than just "Rogue".
The more specific "img,img-axe-1-16m" string refers to individual AXE-1-16M
GPU. For example, unlike the rest of the Series AXE GPUs, the AXE-1-16M
only uses a single power domain.
The situation is actually slightly worse than described in the first
paragraph, since many "series" (such as Series BXS found in the TI AM68
among others and added later in this series) contain cores with both Rogue
and Volcanic architectures.
Besides attempting to move away from vague groupings defined only
by marketing terms, we want to draw a line between properties inherent to
the IP core and choices made by the silicon vendor at integration time.
For instance, the number of power domains is a property of the IP core,
whereas the decision to use one or multiple clocks is a vendor one.
In the original compatible strings, we must use "ti,am62-gpu" to constrain
both of these properties since the number of power domains cannot be fixed
for "img,img-axe".
Work is currently underway to add support for volcanic-based Imagination
GPUs, for which bindings will be added in "img,powervr-volcanic.yaml".
As alluded to previously, the split between rogue and volcanic cores is
non-obvious at times, so add a generic top-level "img,img-rogue" compatible
string here to allow for simpler differentiation in devicetrees without
referring back to the bindings.
The currently supported GPU (AXE-1-16M) only requires a single power
domain. Subsequent patches will add support for BXS-4-64 MC1, which has
two power domains. Add infrastructure now to allow for this.
Also allow the dma-coherent property to be added to IMG Rogue GPUs, which
are DMA devices. The decision for coherency is made at integration time and
this property should be applied wherever it accurately describes the
vendor integration.
Note that the new required properties for power domains are conditional on
the new base compatible string to avoid an ABI break.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250410-sets-bxs-4-64-patch-v1-v6-1-eda620c5865f@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
HDMI standard defines recommended N and CTS values for Audio Clock
Regeneration. Currently each driver implements those, frequently in
somewhat unique way. Provide a generic helper for getting those values
to be used by the HDMI drivers.
The helper is added to drm_hdmi_helper.c rather than drm_hdmi_audio.c
since HDMI drivers can be using this helper function even without
switching to DRM HDMI Audio helpers.
Note: currently this only handles the values per HDMI 1.4b Section 7.2
and HDMI 2.0 Section 9.2.1. Later the table can be expanded to
accommodate for Deep Color TMDS char rates per HDMI 1.4 Appendix D
and/or HDMI 2.0 / 2.1 Appendix C).
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250408-drm-hdmi-acr-v2-1-dee7298ab1af@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Cross-subsystem Changes:
- Update GVT MAINTAINERS (Jani)
Driver Changes:
- Updates for xe3lpd display (Gustavo)
- Fix link training interrupted by HPD pulse (Imre)
- Watermark bound checks for DSC (Ankit)
- VRR Refactor and other fixes and improvements (Ankit)
- More conversions towards intel_display struct (Gustavo, Jani)
- Other clean-up patches towards a display separation (Jani)
- Maintain asciibetical order for HAS_* macros (Ankit)
- Fixes around probe/initialization (Janusz)
- Fix build and doc build issue (Yue, Rodrigo)
- DSI related fixes (Suraj, William, Jani)
- Improve DC6 entry counter (Mohammed)
- Fix xe2hpd memory type identification (Vivek)
- PSR related fixes and improvements (Animesh, Jouni)
- DP MST related fixes and improvements (Imre)
- Fix scanline_offset for LNL+/BMG+ (Ville)
- Some gvt related fixes and changes (Ville, Jani)
- Some PLL code adjustment (Ville)
- Display wa addition (Vinod)
- DRAM type logging (Lucas)
- Pimp the initial FB readout (Ville)
- Some sagv/bw cleanup (Ville)
- Remove i915_display_capabilities debugfs entry (Jani)
- Move PCH type to display caps debugfs entry (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/Z_kTqPX5Mjruq1pL@intel.com
Set default limit on the number of pixels for adapters without
vendor firmware descriptor. The devices work as expected, they
just don't provide any description.
If parsing the vendor firmware descriptor fails, the device falls
back to the given default limits. Failing to allocate memory is
still an error.
v2:
- fix typo in constant (Patrik)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20250410105948.25463-10-tzimmermann@suse.de
Rewrite the parser for the vendor firmware descriptor with the
following improvements.
- Validate the key-value length given in a vendor descriptor
against the length of the descriptor. The current code fails
to do this and might read more bytes than available. This can
lead to out-of-bounds reads of the allocated buffer.
- Read raw data with helpers for unaligned data. This allows
the code to run on platforms that do now support unaligned memory
access by default.
- Validate the pixel limit against a default value. The default
comes from real-world devices. If the reported number of pixels
is significantly above the limit, it is likely invalid.
- Drop the obsolete print macros. There is still a warning about
invalid firmware descriptors. The rest of the output is bogus.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20250410105948.25463-9-tzimmermann@suse.de
There need to be least 5 bytes in the vendor descriptor. Return
an error otherwise. Also change the branching to early-out on
the error. Adjust indention of the rest of the parser function.
The original length test expected more than 5 bytes in the vendor
descriptor. As a descriptor with no key-value pairs has exactly 5
bytes and is still valid, change the test to accept this case as
well.
v2
- clarify changes to length test in commit description (Patrik)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20250410105948.25463-7-tzimmermann@suse.de
Share efidrm's and vesadrm's validation of struct screen_info in
shared helpers. Update the drivers.
Most validation helpers test individual values against limits and
can be shared as they are. For color formats, a common helper looks
up the correct DRM format info from a driver-provided list of color
formats.
These screen_info helpers are only available if CONFIG_SCREEN_INFO
has been selected, as done by efidrm and vesadrm.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250410083834.10810-4-tzimmermann@suse.de
Split drm_sysfb_helper.c into two source files. There's now one
source file for the mode-setting pipeline and one source file for
module meta data. Prepares for adding additional source code to
sysfb helpers.
v2:
- fix typo in commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250410083834.10810-2-tzimmermann@suse.de
drm-misc-next for v6.16-rc1:
UAPI Changes:
- Add ASAHI uapi header!
- Add apple fourcc modifiers.
- Add capset virtio definitions to UAPI.
- Extend EXPORT_SYNC_FILE for timeline syncobjs.
Cross-subsystem Changes:
- Adjust DMA-BUF sg handling to not cache map on attach.
- Update drm/ci, hlcdc, virtio, maintainers.
- Update fbdev todo.
- Allow setting dma-device for dma-buf import.
- Export efi_mem_desc_lookup to make efidrm build as a module.
Core Changes:
- Update drm scheduler docs.
- Use the correct resv object in TTM delayed destroy.
- Fix compiler warning with panic qr code, and other small fixes.
- drm/ci updates.
- Add debugfs file for listing all bridges.
- Small fixes to drm/client, ttm tests.
- Add documentation to display/hdmi.
- Add kunit tests for bridges.
- Dont fail managed device probing if connector polling fails.
- Create Kconfig.debug for drm core.
- Add tests for the drm scheduler.
- Add and use new access helpers for DPCPD.
- Add generic and optimized conversions for format-helper.
- Begin refcounting panel for improving lifetime handling.
- Unify simpledrm and ofdrm sysfb, and add extra features.
- Split hdmi audio in bridge to make DP audio work.
Driver Changes:
- Convert drivers to use devm_platform_ioremap_resource().
- Assorted small fixes to imx/legacy-bridg, gma500, pl111, nouveau, vc4,
vmwgfx, ast, mxsfb, xlnx, accel/qaic, v3d, bridge/imx8qxp-ldb, ofdrm,
bridge/fsl-ldb, udl, bridge/ti-sn65dsi86, bridge/anx7625, cirrus-qemu,
bridge/cdns-dsi, panel/sharp, panel/himax, bridge/sil902x, renesas,
imagination, various panels.
- Allow attaching more display to vkms.
- Add Powertip PH128800T004-ZZA01 panel.
- Add rotation quirk for ZOTAC panel.
- Convert bridge/tc358775 to atomic.
- Remove deprecated panel calls from synaptics, novatek, samsung panels.
- Refactor shmem helper page pinning and accel drivers using it.
- Add dmabuf support to accel/amdxdna.
- Use 4k page table format for panfrost/mediatek.
- Add common powerup/down dp link helper and use it.
- Assorted compiler warning fixes.
- Support dma-buf import for renesas
Signed-off-by: Dave Airlie <airlied@redhat.com>
# Conflicts:
# include/drm/drm_kunit_helpers.h
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/e147ff95-697b-4067-9e2e-7cbd424e162a@linux.intel.com
Pull erofs fixes from Gao Xiang:
- Properly handle errors when file-backed I/O fails
- Fix compilation issues on ARM platform (arm-linux-gnueabi)
- Fix parsing of encoded extents
- Minor cleanup
* tag 'erofs-for-6.15-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: remove duplicate code
erofs: fix encoded extents handling
erofs: add __packed annotation to union(__le16..)
erofs: set error to bio if file-backed IO fails
Pull ext4 fixes from Ted Ts'o:
"A few more miscellaneous ext4 bug fixes and cleanups including some
syzbot failures and fixing a stale file handing refeencing an inode
previously used as a regular file, but which has been deleted and
reused as an ea_inode would result in ext4 erroneously considering
this a case of fs corruption"
* tag 'ext4_for_linus-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix off-by-one error in do_split
ext4: make block validity check resistent to sb bh corruption
ext4: avoid -Wflex-array-member-not-at-end warning
Documentation: ext4: Add fields to ext4_super_block documentation
ext4: don't treat fhandle lookup of ea_inode as FS corruption
Pull memblock fix from Mike Rapoport:
"Fix build of memblock test.
Add missing stubs for mutex and free_reserved_area() to memblock
tests"
* tag 'fixes-2025-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock tests: Fix mutex related build error
Syzkaller detected a use-after-free issue in ext4_insert_dentry that was
caused by out-of-bounds access due to incorrect splitting in do_split.
BUG: KASAN: use-after-free in ext4_insert_dentry+0x36a/0x6d0 fs/ext4/namei.c:2109
Write of size 251 at addr ffff888074572f14 by task syz-executor335/5847
CPU: 0 UID: 0 PID: 5847 Comm: syz-executor335 Not tainted 6.12.0-rc6-syzkaller-00318-ga9cda7c0ffed #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/30/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
kasan_check_range+0x282/0x290 mm/kasan/generic.c:189
__asan_memcpy+0x40/0x70 mm/kasan/shadow.c:106
ext4_insert_dentry+0x36a/0x6d0 fs/ext4/namei.c:2109
add_dirent_to_buf+0x3d9/0x750 fs/ext4/namei.c:2154
make_indexed_dir+0xf98/0x1600 fs/ext4/namei.c:2351
ext4_add_entry+0x222a/0x25d0 fs/ext4/namei.c:2455
ext4_add_nondir+0x8d/0x290 fs/ext4/namei.c:2796
ext4_symlink+0x920/0xb50 fs/ext4/namei.c:3431
vfs_symlink+0x137/0x2e0 fs/namei.c:4615
do_symlinkat+0x222/0x3a0 fs/namei.c:4641
__do_sys_symlink fs/namei.c:4662 [inline]
__se_sys_symlink fs/namei.c:4660 [inline]
__x64_sys_symlink+0x7a/0x90 fs/namei.c:4660
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
The following loop is located right above 'if' statement.
for (i = count-1; i >= 0; i--) {
/* is more than half of this entry in 2nd half of the block? */
if (size + map[i].size/2 > blocksize/2)
break;
size += map[i].size;
move++;
}
'i' in this case could go down to -1, in which case sum of active entries
wouldn't exceed half the block size, but previous behaviour would also do
split in half if sum would exceed at the very last block, which in case of
having too many long name files in a single block could lead to
out-of-bounds access and following use-after-free.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Cc: stable@vger.kernel.org
Fixes: 5872331b3d ("ext4: fix potential negative array index in do_split()")
Signed-off-by: Artem Sadovnikov <a.sadovnikov@ispras.ru>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250404082804.2567-3-a.sadovnikov@ispras.ru
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
