Add support for low power mode to the Ingenic's MMC/SD Controller.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the JZ4760 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
SDXC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new compatible to use the sdhc-arasan host controller driver
with the SDXC PHY to support on Intel's Lightning Mountain(LGM) SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds busy_completion callback at mmci_host_ops
to allow to define a specific busy completion by variant.
The legacy code corresponding to busy completion used
by ux500 variants is moved to ux500_busy_complete function.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the stm32_sdmmc variant, the datatimer is active not only during
data transfers with the DPSM, but also while waiting for the busyend
IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an
incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which
simply breaks the behaviour.
Address this by updating the datatimer value before sending a command
having the MMC_RSP_BUSY flag set. To inform the mmc core about the
maximum supported busy timeout, which also depends on the current
clock rate, set ->max_busy_timeout (in ms).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warnings by making any functions not used
outsde the mmci.c driver static.
drivers/mmc/host/mmci.c:422:6: warning: symbol 'mmci_dma_release' was not declared. Should it be static?
drivers/mmc/host/mmci.c:430:6: warning: symbol 'mmci_dma_setup' was not declared. Should it be static?
drivers/mmc/host/mmci.c:465:5: warning: symbol 'mmci_prep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:481:6: warning: symbol 'mmci_unprep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:490:6: warning: symbol 'mmci_get_next_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:498:5: warning: symbol 'mmci_dma_start' was not declared. Should it be static?
drivers/mmc/host/mmci.c:533:6: warning: symbol 'mmci_dma_finalize' was not declared. Should it be static?
drivers/mmc/host/mmci.c:542:6: warning: symbol 'mmci_dma_error' was not declared. Should it be static?
drivers/mmc/host/mmci.c:951:6: warning: symbol 'mmci_variant_init' was not declared. Should it be static?
drivers/mmc/host/mmci.c:956:6: warning: symbol 'ux500v2_variant_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a couple of statements that are indented by an extra
space, clean this up by remove the extraneous spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a hunk of code that is indented one level too deep, fix
this by removing the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PM has been reworked, so eMMC gets now detected on R-Car H3 ES1.0 and
2.0 as well as M3-N without the workaround. Card detect and write
protect also still work. Remove the workaround.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently
supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is
supported but it is untested. There is no SDIO support for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD Host controller on Milbeaut consists of two controller parts.
One is core controller F_SDH30, this is similar to sdhci-fujitsu
controller.
Another is bridge controller.
This bridge controller is not compatible with sdhci-fujitsu controller.
This is special for Milbeaut series. This has some functions.
For example, reset control, clock enable/select for SDR50/25/12, set
property of SD physical pins, retuning control, set capabilityies.
This bridge controller requires special procedures at reset or clock
enablement or change for further tuning of clock.
Signed-off-by: Takao Orito <orito.takao@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SDHC 0x7906 requires a hard reset to clear all internal state.
Otherwise it can get into a bad state where the DATA lines are always
read as zeros.
This change requires firmware that can transition the device into
D3Cold for it to work correctly. If the firmware does not support
transitioning to D3Cold then the power state transitions are a no-op.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdhci_do_reset we call the reset callback which is typically
sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the
controller to reset. If SDHCI_RESET_ALL was passed as the flag, the
controller will clear the IRQ mask. If during that 100ms the card is
removed there is no notification to the MMC system that the card was
removed. So from the drivers point of view the card is always present.
By making sdhci_reinit compare the present state it can schedule a
rescan if the card was removed while a reset was in progress.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
Pull IIO fixes and staging driver from Greg KH:
"Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole
new staging driver.
The IIO fixes resolve some reported issues, all are tiny.
The staging driver addition is the vboxsf filesystem, which is the
VirtualBox guest shared folder code. Hans has been trying to get
filesystem reviewers to review the code for many months now, and
Christoph finally said to just merge it in staging now as it is
stand-alone and the filesystem people can review it easier over time
that way.
I know it's late for this big of an addition, but it is stand-alone.
The code has been in linux-next for a while, long enough to pick up a
few tiny fixes for it already so people are looking at it.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: Fix error return code in vboxsf_fill_super()
staging: vboxsf: fix dereference of pointer dentry before it is null checked
staging: vboxsf: Remove unused including <linux/version.h>
staging: Add VirtualBox guest shared folder (vboxsf) support
iio: adc: stm32-adc: fix stopping dma
iio: imu: inv_mpu6050: fix no data on MPU6050
iio: srf04: fix wrong limitation in distance measuring
iio: imu: adis16480: make sure provided frequency is positive
Pull char/misc driver fixes from Greg KH:
"Here are a number of late-arrival driver fixes for issues reported for
some char/misc drivers for 5.4-rc7
These all come from the different subsystem/driver maintainers as
things that they had reports for and wanted to see fixed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
intel_th: pci: Add Jasper Lake PCH support
intel_th: pci: Add Comet Lake PCH support
intel_th: msu: Fix possible memory leak in mode_store()
intel_th: msu: Fix overflow in shift of an unsigned int
intel_th: msu: Fix missing allocation failure check on a kstrndup
intel_th: msu: Fix an uninitialized mutex
intel_th: gth: Fix the window switching sequence
soundwire: slave: fix scanf format
soundwire: intel: fix intel_register_dai PDI offsets and numbers
interconnect: Add locking in icc_set_tag()
interconnect: qcom: Fix icc_onecell_data allocation
soundwire: depend on ACPI || OF
soundwire: depend on ACPI
thunderbolt: Drop unnecessary read when writing LC command in Ice Lake
thunderbolt: Fix lockdep circular locking depedency warning
thunderbolt: Read DP IN adapter first two dwords in one go
Pull configfs regression fix from Christoph Hellwig:
"Fix a regression from this merge window in the configfs symlink
handling (Honggang Li)"
* tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs:
configfs: calculate the depth of parent item
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Make the tsc=reliable/nowatchdog command line parameter work again.
It was broken with the introduction of the early TSC clocksource.
- Prevent the evaluation of exception stacks before they are set up.
This causes a crash in dumpstack because the stack walk termination
gets screwed up.
- Prevent a NULL pointer dereference in the rescource control file
system.
- Avoid bogus warnings about APIC id mismatch related to the LDR
which can happen when the LDR is not in use and therefore not
initialized. Only evaluate that when the APIC is in logical
destination mode"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early
x86/dumpstack/64: Don't evaluate exception stacks before setup
x86/apic/32: Avoid bogus LDR warnings
x86/resctrl: Prevent NULL pointer dereference when reading mondata
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for scheduler regressions:
- Plug a subtle race condition which was introduced with the rework
of the next task selection functionality. The change of task
properties became unprotected which can be observed inconsistently
causing state corruption.
- A trivial compile fix for CONFIG_CGROUPS=n"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix pick_next_task() vs 'change' pattern race
sched/core: Fix compilation error when cgroup not selected
Pull perf tooling fixes from Thomas Gleixner:
- Fix the time sorting algorithm which was broken due to truncation of
big numbers
- Fix the python script generator fail caused by a broken tracepoint
array iterator
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix time sorting
perf tools: Remove unused trace_find_next_event()
perf scripting engines: Iterate on tep event arrays directly
Pull irq fixlet from Thomas Gleixner:
"A trivial fix for a kernel doc regression where an argument change was
not reflected in the documentation"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
Pull stacktrace fix from Thomas Gleixner:
"A small fix for a stacktrace regression.
Saving a stacktrace for a foreign task skipped an extra entry which
makes e.g. the output of /proc/$PID/stack incomplete"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace: Don't skip first entry on noncurrent tasks
Pull cifs fix from Steve French:
"Small fix for an smb3 reconnect bug (also marked for stable)"
* tag '5.4-rc7-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
SMB3: Fix persistent handles reconnect
config option GENERIC_IO was removed but still selected by lib/kconfig
This patch finish the cleaning.
Fixes: 9de8da4774 ("kconfig: kill off GENERIC_IO option")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull btrfs fixes from David Sterba:
"A few regressions and fixes for stable.
Regressions:
- fix a race leading to metadata space leak after task received a
signal
- un-deprecate 2 ioctls, marked as deprecated by mistake
Fixes:
- fix limit check for number of devices during chunk allocation
- fix a race due to double evaluation of i_size_read inside max()
macro, can cause a crash
- remove wrong device id check in tree-checker"
* tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: un-deprecate ioctls START_SYNC and WAIT_SYNC
btrfs: save i_size to avoid double evaluation of i_size_read in compress_file_range
Btrfs: fix race leading to metadata space leak after task received signal
btrfs: tree-checker: Fix wrong check on max devid
btrfs: Consider system chunk array size for new SYSTEM chunks
Pull watchdog fixes from Wim Van Sebroeck:
- cpwd: fix build regression
- pm8916_wdt: fix pretimeout registration flow
- meson: Fix the wrong value of left time
- imx_sc_wdt: Pretimeout should follow SCU firmware format
- bd70528: Add MODULE_ALIAS to allow module auto loading
* tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading
watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format
watchdog: meson: Fix the wrong value of left time
watchdog: pm8916_wdt: fix pretimeout registration flow
watchdog: cpwd: fix build regression
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
Pull block fixes from Jens Axboe:
- Two NVMe device removal crash fixes, and a compat fixup for for an
ioctl that was introduced in this release (Anton, Charles, Max - via
Keith)
- Missing error path mutex unlock for drbd (Dan)
- cgroup writeback fixup on dead memcg (Tejun)
- blkcg online stats print fix (Tejun)
* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
block: drbd: remove a stray unlock in __drbd_send_protocol()
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
