Support the kernel's nomodeset parameter for all PCI-based fbdev
drivers that use aperture helpers to remove other, hardware-agnostic
graphics drivers.
The parameter is a simple way of using the firmware-provided scanout
buffer if the hardware's native driver is broken. The same effect
could be achieved with per-driver options, but the importance of the
graphics output for many users makes a single, unified approach
worthwhile.
With nomodeset specified, the fbdev driver module will not load. This
unifies behavior with similar DRM drivers. In DRM helpers, modules
first check the nomodeset parameter before registering the PCI
driver. As fbdev has no such module helpers, we have to modify each
driver individually.
The name 'nomodeset' is slightly misleading, but has been chosen for
historical reasons. Several drivers implemented it before it became a
general option for DRM. So keeping the existing name was preferred over
introducing a new one.
v2:
* print a warning if a driver does not init (Helge)
* wrap video_firmware_drivers_only() in helper
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221111133024.9897-3-tzimmermann@suse.de
Move the nomodeset kernel parameter to drivers/video to make it
available to non-DRM drivers. Adapt the interface, but keep the DRM
interface drm_firmware_drivers_only() to avoid churn within DRM. The
function should later be inlined into callers.
The parameter disables any DRM graphics driver that would replace a
driver for firmware-provided scanout buffers. It is an option to easily
fallback to basic graphics output if the hardware's native driver is
broken. Moving it to a more prominent location wil make it available
to fbdev as well.
v2:
* clarify the meaning of the nomodeset parameter (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221111133024.9897-2-tzimmermann@suse.de
Schedule the deferred-I/O worker instead of the damage worker after
writing to the fbdev framebuffer. The deferred-I/O worker then performs
the dirty-fb update. The fbdev emulation will initialize deferred I/O
for all drivers that require damage updates. It is therefore a valid
assumption that the deferred-I/O worker is present.
It would be possible to perform the damage handling directly from within
the write operation. But doing this could increase the overhead of the
write or interfere with a concurrently scheduled deferred-I/O worker.
Instead, scheduling the deferred-I/O worker with its regular delay of
50 ms removes load off the write operation and allows the deferred-I/O
worker to handle multiple write operations that arrived during the delay
time window.
v3:
* remove unused variable (lkp)
v2:
* keep drm_fb_helper_damage() (Daniel)
* use fb_deferred_io_schedule_flush() (Daniel)
* clarify comments (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20221115115819.23088-6-tzimmermann@suse.de
Call fb_dirty directly from drm_fb_helper_deferred_io() to avoid the
latency of running the damage worker.
The deferred-I/O helper drm_fb_helper_deferred_io() runs in a worker
thread at regular intervals as part of writing to mmaped framebuffer
memory. It used to schedule the fbdev damage worker to flush the
framebuffer. Changing this to flushing the framebuffer directly avoids
the latency introduced by the damage worker.
v2:
* remove fb_dirty from defio in separate patch (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20221115115819.23088-5-tzimmermann@suse.de
drm_mode_config_init() simply calls drmm_mode_config_init(), hence
cleanup is automatically handled through registering
drm_mode_config_cleanup() with drmm_add_action_or_reset().
While at it, get rid of the deprecated drm_mode_config_init() and
replace it with drmm_mode_config_init() directly.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026155934.125294-6-dakr@redhat.com
The current code to deal with named modes will only set the mode name, and
then it's up to drivers to try to match that name to whatever mode or
configuration they see fit.
The plan is to remove that need and move the named mode handling out of
drivers and into the core, and only rely on modes and properties. Let's
start by properly filling drm_cmdline_mode from a named mode.
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v9-11-24b168e5bcd5@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-8-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-5-ville.syrjala@linux.intel.com
Summary:
* Add support to turn on/off backlight when changing values in bl_power
file. This is achieved by using function backlight_get_brightness()
in nva3_set_intensity to get current brightness.
Test plan:
* Turn off:
echo 1 > /sys/class/backlight/nv_backlight/bl_power
* Turn on:
echo 0 > /sys/class/backlight/nv_backlight/bl_power
Signed-off-by: Antonio Gomes <antoniospg100@gmail.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221104220424.41164-1-antoniospg100@gmail.com
v3d_perfmon_open_file() instantiates a mutex for a particular file
instance, but it never destroys it by calling mutex_destroy() in
v3d_perfmon_close_file().
Similarly, v3d_perfmon_create_ioctl() instantiates a mutex for a
particular perfmon, but it never destroys it by calling mutex_destroy()
in v3d_perfmon_destroy_ioctl().
So, add the missing mutex_destroy on both cases.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221108175425.39819-3-mcanal@igalia.com
In case the LCDIFv3 is used to drive a 4k panel via i.MX8MP HDMI bridge,
the LCDIFv3 becomes susceptible to FIFO underflows, these lead to nasty
flicker of the image on the panel, or image being shifted by half frame
horizontally every second frame. The flicker can be easily triggered by
running 3D application on top of weston compositor, like neverball or
chromium. Surprisingly glmark2-es2-wayland or glmark2-es2-drm does not
trigger this effect so easily.
Configure the FIFO Panic threshold register and enable the FIFO Panic
mode, which internally boosts the NoC interconnect priority for LCDIFv3
transactions in case of possible underflow. This mitigates the flicker
effect on 4k panels as well.
Fixes: 9db35bb349 ("drm: lcdif: Add support for i.MX8MP LCDIF variant")
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Liu Ying <victor.liu@nxp.com> # i.MX8mp EVK
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221101152629.21768-1-marex@denx.de
