Currently buf_len field of ath12k_mhi_config_wcn7850 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
For now we haven't get any failure report on this in ath12k, but
there indeed is one such case in ath11k [1].
Actually those buffers are used only by QMI target -> host communication.
And for WCN7850, the largest packet size for that is less than 6KB. So
change buf_len field to 8KB, which results in order 1 allocation if page
size is 4KB. In this way, we can at least save some memory, and as well
as decrease the possibility of allocation failure in those scenarios.
[1] https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-6-quic_bqiang@quicinc.com
We are seeing below warning in both reset and suspend/resume scenarios:
[ 4153.776040] ath12k_pci 0000:04:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath12k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-5-quic_bqiang@quicinc.com
Both the firmware reset feature and the power management
suspend/resume feature share common power-down and power-up
functionality. One aspect of the power-up functionality is
the handling of the ATH12K_QMI_EVENT_FW_INIT_DONE event.
When this event is received, a call is made to
ath12k_hal_dump_srng_stats(), with the purpose to collect
information that may be useful in debugging the cause of a
firmware reset.
Unfortunately, since this functionality is shared between
both the firmware reset path and the power management
resume path, the kernel log is flooded with messages during
resume. Since these messages are not useful during resume,
and in fact can be confusing and can increase the time it
takes to resume, update the logic to only call
ath12k_hal_dump_srng_stats() during firmware reset.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-4-quic_bqiang@quicinc.com
There is no driver to match these two channels, so
remove them. This fixes warnings from MHI subsystem during suspend:
mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting
mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-3-quic_bqiang@quicinc.com
For non-WoW suspend/resume, ath12k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath12k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-2-quic_bqiang@quicinc.com
Currently during resume, QMI target memory is not properly handled, resulting
in kernel crash in case DMA remap is not supported:
BUG: Bad page state in process kworker/u16:54 pfn:36e80
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80
page dumped because: nonzero _refcount
Call Trace:
bad_page
free_page_is_bad_report
__free_pages_ok
__free_pages
dma_direct_free
dma_free_attrs
ath12k_qmi_free_target_mem_chunk
ath12k_qmi_msg_mem_request_cb
The reason is:
Once ath12k module is loaded, firmware sends memory request to host. In case
DMA remap not supported, ath12k refuses the first request due to failure in
allocating with large segment size:
ath12k_pci 0000:04:00.0: qmi firmware request memory request
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144
ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size
ath12k_pci 0000:04:00.0: qmi delays mem_request 2
ath12k_pci 0000:04:00.0: qmi firmware request memory request
Later firmware comes back with more but small segments and allocation
succeeds:
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
Now ath12k is working. If suspend is triggered, firmware will be reloaded
during resume. As same as before, firmware requests two large segments at
first. In ath12k_qmi_msg_mem_request_cb() segment count and size are
assigned:
ab->qmi.mem_seg_count == 2
ab->qmi.target_mem[0].size == 7077888
ab->qmi.target_mem[1].size == 8454144
Then allocation failed like before and ath12k_qmi_free_target_mem_chunk()
is called to free all allocated segments. Note the first segment is skipped
because its v.addr is cleared due to allocation failure:
chunk->v.addr = dma_alloc_coherent()
Also note that this leaks that segment because it has not been freed.
While freeing the second segment, a size of 8454144 is passed to
dma_free_coherent(). However remember that this segment is allocated at
the first time firmware is loaded, before suspend. So its real size is
524288, much smaller than 8454144. As a result kernel found we are freeing
some memory which is in use and thus crashed.
So one possible fix would be to free those segments during suspend. This
works because with them freed, ath12k_qmi_free_target_mem_chunk() does
nothing: all segment addresses are NULL so dma_free_coherent() is not called.
But note that ath11k has similar logic but never hits this issue. Reviewing
code there shows the luck comes from QMI memory reuse logic. So the decision
is to port it to ath12k. Like in ath11k, the crash is avoided by adding
prev_size to target_mem_chunk structure and caching real segment size in it,
then prev_size instead of current size is passed to dma_free_coherent(),
no unexpected memory is freed now.
Also reuse m3 buffer.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240419034034.2842-1-quic_bqiang@quicinc.com
Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence
facing below KASAN warning,
==================================================================
BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148
Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273
CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0
Workqueue: qmi_msg_handler qmi_data_ready_work
Call trace:
dump_backtrace+0x0/0x20c
show_stack+0x14/0x1c
dump_stack+0xe0/0x138
print_address_description.isra.5+0x30/0x330
__kasan_report+0x16c/0x1bc
kasan_report+0xc/0x14
__asan_load8+0xa8/0xb0
qmi_invoke_handler+0xa4/0x148
qmi_handle_message+0x18c/0x1bc
qmi_data_ready_work+0x4ec/0x528
process_one_work+0x2c0/0x440
worker_thread+0x324/0x4b8
kthread+0x210/0x228
ret_from_fork+0x10/0x18
The address belongs to the variable:
ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k]
[...]
==================================================================
Add a dummy terminator entry at the end to assist the qmi_invoke_handler()
in traversing up to the terminator entry without accessing an
out-of-boundary index.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416080234.2882725-1-quic_kathirve@quicinc.com
Move the data path Tx and Rx descriptor primary page table CMEM
configuration into a helper function. This will make the code more
scalable for configuring partner device in support of multi-device MLO.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-5-quic_periyasa@quicinc.com
In the hardware cookie conversion table configuration, place the Rx
descriptor at the end. This will allow for easier addition of partner
device Rx descriptors in the future to support multi-device MLO.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-4-quic_periyasa@quicinc.com
Currently, the Rx descriptor is placed before the Tx descriptor in the
primary page table of the hardware cookie conversion configuration. The
Tx and Rx descriptor offsets are implicitly hardcoded. To allow for easy
displacement of Tx and Rx descriptors, introduce Tx and Rx offset based
cookie conversion initializationi. Additionally, should consider
validating the respective offset ranges while retrieving the Tx and Rx
descriptors. This change will be utilize by the next patch in the series.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-3-quic_periyasa@quicinc.com
Currently, in the Rx data path cookie conversion initialization procedure,
the primary page table index (ppt_idx) is computed within the secondary
page table iteration. However this is invariant, and hence the ppt_idx
should be calculated outside of the iteration to avoid repeated execution
of the statement.
Found in code review.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-2-quic_periyasa@quicinc.com
Currently, when debug logs are enabled, messages such as the following
are found in the kernel log:
event mgmt rx skb pK-error len 209 ftype 00 stype 50
The "pK-error" comes from using %pK to display an skb address in an
interrupt context.
Per the guidance in the current "printk-formats" documentation, %pK
"is only intended when producing content of a file read by userspace
from e.g. procfs or sysfs, not for dmesg."
So replace %pK with %p in all of the ath12k_dbg() format strings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
The survey dump statistics does not display channel RX and TX time
properly because the survey flag is not enabled in the firmware service
flag.
If firmware supports enable the service flag "bss_chan_info" in
wmi_resource_config to fetch and print the stats for specific pdev.
Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact
on WCN7850 since this bit is not utilized by the WCN7850 firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
ath12k will support Multi-Link Operation (MLO) in the future but not yet. A
major change with MLO is that cfg80211 will disable Wireless Extension (WEXT)
user space interface. To avoid having inconsistent user experience, first
supporting WEXT and later not, disable WEXT already now.
Now ath12k claims that WEXT is not supported:
$ iwconfig wlan0
wlan0 no wireless extensions.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240411165645.4071238-1-kvalo@kernel.org
Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
Currently, in the rx error data path, mac id is extracted from the
last 64bits of MSDU end description tag for each entry received in
the WBM error ring. Then, each entry will be updated into the MSDU
list for further processing. The extracted mac id is valid when a
single MSDU is not fragmented and received in the WBM error ring.
In scenarios where the size of a single MSDU received exceeds the
descriptor buffer size, resulting in fragmented or spillover MSDU
entries into the WBM error ring. In this case, the extracted mac id
from each spillover entry is invalid except the last spillover entry
of the MSDU. This invalid mac id leads to packet rejection.
To address this issue, check if the MSDU continuation flag is set,
then extract the valid mac id from the last spillover entry.
Propagate the valid mac id to all the spillover entries of the single
MSDU in the temporary MSDU list(scatter_msdu_list). Then, update this
into the MSDU list (msdu_list) for further processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240404141538.1277258-1-quic_nithp@quicinc.com
The radio for which the survey info needs to be collected
depends on the channel idx which could be based on the band.
Use the idx to identify the appropriate sband since multiple
bands could be combined for single wiphy case.
Also use the channel idx and sband to identify the corresponding
radio on which the survey results needs to be populated.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-13-quic_ramess@quicinc.com
Since multiple radios are abstracted under a single wiphy,
apply the rts threshold value to all the vdevs of the radios
combined under single wiphy.
This also implies that vif specific rts threshold support
needs to be added in future from cfg80211/mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-12-quic_ramess@quicinc.com
As multiple radios are combined into a single wiphy, and
the current infrastructure supports only set/get antenna
for the wiphy, the max Tx/Rx antenna capability is advertised
during wiphy register.
Hence, When antenna set/get is received we adjust the set/get
based on max radio capability and set/get antenna accordingly.
Multi radio capability needs to introduced with interface
combination changes to support single wiphy model in cfg80211
which would help extend the wiphy specific get/set configs similar
to this to per hw level.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-11-quic_ramess@quicinc.com
With all the radios being combined and registered as a single
mac80211 hw/wiphy, separate regd built from firmware rules need
not be updated to cfg80211. Rather we can pick one of the regd
built from the rules to update to cfg80211 for the whole
registered device. We prefer 6 GHz pdev based rules since it has
the rules for all bands. If the hw doesn't support 6 GHz, then update
rules from one of the pdevs.
Also, when regulatory notification is received, update to all the
underlying radios/ar so that it becomes aware of the change and as
well us it updates its local regd with the new country rules. Later
pick the appropriate pdev's regd(6 GHz if available) and apply to
cfg80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-10-quic_ramess@quicinc.com
Since vif and sta objects of different radios are added to same
local hw list in mac80211, additional checks need to be done
in driver to ensure we are processing the intended vif
and sta corresponding to the radio when the vif and sta mac80211
iterator utils are used from driver.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-9-quic_ramess@quicinc.com
Since the vdev create for a corresponding vif is deferred
until a channel is assigned, cache the information which
are received through mac80211 ops between add_interface()
and assign_vif_chanctx() and set them once the vdev is
created on one of the ath12k radios as the channel gets
assigned via assign_vif_chanctx().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-8-quic_ramess@quicinc.com
For ops which passes the vif info, fetch the radio(ar)
to be used for corresponding functions based on the
the vdev creation status. If the vdev is not created yet,
which could happen when the ops are called before channel
is assigned for the vif, the data needs to be cached and this
is done in followup changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-7-quic_ramess@quicinc.com
When multiple radios are advertised as a single wiphy which
supports various bands, a default scan request to mac80211
from cfg80211 will split the driver request based on band,
so each request will have channels belonging to the same band.
With this supported by default, the ath12k driver on receiving
this request checks for one of the channels in the request and
selects the corresponding radio(ar) on which the scan is going
to be performed and creates a vdev on that radio.
Note that on scan completion this vdev is not deleted. If a new
scan request is seen on that same vif for a different band the
vdev will be deleted and created on the new radio supporting the
request. The vdev delete logic is refactored to have this done
dynamically.
The reason for not deleting the vdev on scan stop is to avoid
repeated delete-create sequence if the scan is on the same band.
Also, during channel assign, new vdev creation can be optimized
as well.
Also if the scan is requested when the vdev is in started state,
no switching to new radio is allowed and scan on channels only
within same radio is allowed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-6-quic_ramess@quicinc.com
With single wiphy, multiple radios are combined into a single wiphy.
Since any channel can be assigned to a vif being brought up,
the vdev cannot be created during add_interface(). Hence defer the
vdev creation till channel assignment.
If only one radio is part of the wiphy, then the existing logic
is maintained, i.e vdevs are created during add interface and
started during channel assignment. This ensures no functional changes
to single pdev devices which has only one radio in the SoC.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-5-quic_ramess@quicinc.com
Modify add and remove chanctx mac80211 ops to fetch the correct
radio(ar) based on channel context.
This change also introduces new helper function to fetch the
radio/ar based on channel context and ieee80211_chan which internally
uses the radio's low/high freq range.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-3-quic_ramess@quicinc.com
Currently MAC HW un/register helper function support the single radio.
To enable single/multi link operation in the future, the following helper
functions need to be refactored to accommodate multiple radios under a
single MAC HW un/register:
* ath12k_ah_to_ar()
* ath12k_mac_hw_allocate()
* ath12k_mac_hw_register()
* ath12k_mac_hw_unregister()
This refactoring will make it easier to scale these functionalities and
support Multi link operation.
Current Multi wiphy Model
+---------------+ +---------------+ +---------------+
| Mac80211 hw | | Mac80211 hw | | Mac80211 hw |
| private data | | private data | | private data |
| | | | | |
|ath12k_hw (ah) | |ath12k_hw (ah) | |ath12k_hw (ah) |
| | | | | |
| +-----------+ | | +-----------+ | | +-----------+ |
| | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | |
| +-----------+ | | +-----------+ | | +-----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
Single wiphy Model
+--------------+
| Mac80211 hw |
| private data |
| |
|ath12k hw (ah)|
| +----------+ |
| |ar (2GHz) | |
| +----------+ |
| |ar (5GHz) | |
| +----------+ |
| |ar (6GHz) | |
| +----------+ |
+--------------+
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-2-quic_ramess@quicinc.com
Now that all infrastructure is in place and ath11k is fixed to handle all the
corner cases, power down the ath11k firmware during suspend and power it back
up during resume. This fixes the problem when using hibernation with ath11k PCI
devices.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath11k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath11k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath11k's suspend callback before all suspend_late callbacks, making the first
condition happy. And because MHI devices are children of ath11k device
(ab->dev), kernel guarantees that ath11k's suspend_late callback is called
after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath11k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which won't fail now
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the probe-defer issue when resume.
Also change related code due to interface changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305021320.3367-4-quic_bqiang@quicinc.com
MHI devices may not be destroyed during suspend/hibernation, so need
to unprepare/prepare MHI channels throughout the transition, this is
done by adding suspend/resume callbacks.
The suspend callback is called in the late suspend stage, this means
MHI channels are still alive at suspend stage, and that makes it
possible for an MHI controller driver to communicate with others over
those channels at suspend stage. While the resume callback is called
in the early resume stage, for a similar reason.
Also note that we won't do unprepare/prepare when MHI device is in
suspend state because it's pointless if MHI is only meant to go through
a suspend/resume transition, instead of a complete power cycle.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305021320.3367-3-quic_bqiang@quicinc.com
By default driver supports intra-device SLO/MLO, the link capability flags
reflect this. When the QMI PHY capability learning fails driver not enable
the MLO parameter in the host capability QMI request message. In this case,
reset the device link capability flags to zero (SLO/MLO not support) to
accurately represent the capabilities.
Found in code review.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240403042056.1504209-3-quic_periyasa@quicinc.com
Link capability categorized as Single Link Operation (SLO) and Multi Link
Operation (MLO).
- Intra-device SLO/MLO refers to links present within a device
- Inter-device SLO/MLO refers to links present across multiple devices
Currently, driver uses a boolean variable to represent intra-device SLO/MLO
capability. To accommodate inter-device SLO/MLO capabilities within the
same variable, modify the existing variable name and type. Define a new
enumeration for the link capabilities to accommodate both intra-device
and inter-device scenarios. Populate the enum based on the supported
capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240403042056.1504209-2-quic_periyasa@quicinc.com
Different Qualcomm platforms using WCN3990 WiFI chip use SoC-specific
firmware versions with different features. For example firmware for
SDM845 doesn't use single-chan-info-per-channel feature, while firmware
for QRB2210 / QRB4210 requires that feature. Allow board DT files to
override the subdir of the fw dir used to lookup the firmware-N.bin file
decribing corresponding WiFi firmware.
For example:
- ath10k/WCN3990/hw1.0/wlanmdsp.mbn,
ath10k/WCN3990/hw1.0/firmware-5.bin: main firmware files, used by default
- ath10k/WCN3990/hw1.0/qcm2290/wlanmdsp.mbn,
ath10k/WCN3990/hw1.0/qcm2290/firmware-5.bin: SoC specific firmware
with different signature and feature bits
Note, while board files lookup uses the same function and thus it is
possible to provide board-specific board-2.bin files, this is not
required in 99% of cases as board-2.bin already contains a way to
provide board-specific data with finer granularity than DT overrides.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240306-wcn3990-firmware-path-v2-2-f89e98e71a57@linaro.org
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329171019.63836-2-krzysztof.kozlowski@linaro.org
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/wmi.c:4018:49: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSTCmdP+omePvWg@neat
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/cfg80211.c:896:43: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSP/CMSVfr68R2u@neat
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Fixes: fb5f6a0e80 ("mac80211: Use memset_after() to clear tx status")
Link: https://lore.kernel.org/lkml/20230623152443.2296825-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-2-arnd@kernel.org
The initial debugfs infra bringup in ath12k driver and create the ath12k debugfs
and soc-specific directories in /sys/kernel/debug/
For each ath12k device, directory will be created in <bus>-<devname>
schema under ath12k root directory.
Example with one ath12k device:
/sys/kernel/debug/ath12k/pci-0000:06:00.0
ath12k
`-- pci-0000:06:00.0
|-- mac0
To enable ath12k debugfs support (CONFIG_ATH12K_DEBUGFS=y)
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320171305.655288-2-quic_rgnanase@quicinc.com
Petr Machata says:
====================
mlxsw: Preparations for improving performance
Amit Cohen writes:
mlxsw driver will use NAPI for event processing in a next patch set.
Some additional improvements will be added later. This patch set
prepares the code for NAPI usage and refactor some relevant areas. See
more details in commit messages.
Patch Set overview:
Patches #1-#2 are preparations for patch #3
Patch #3 setups tasklets as part of queue initializtion
Patch #4 removes handling of unlikely scenario
Patch #5 removes unused counters
Patch #6 makes style change in mlxsw_pci_eq_tasklet()
Patch #7-#10 poll command interface instead of EQ0 usage
Patches #11-#12 make style change and break the function
mlxsw_pci_cq_tasklet()
Patches #13-#14 remove functions which can be replaced by a stored value
Patch #15 improves accessing to descriptor queue instance
====================
Link: https://lore.kernel.org/r/cover.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
