The Rock 5 ITX only needs enablement for 2 nodes in order to send audio
on HDMI1, the connector closer to the 12V barrel jack and farther from
S/PDIF. It is sufficient to declare the audio injection as okay, and
to activate I2S6.
Note that for the other HDMI output it is not that trivial, as the video
data there originates from the SoC's DisplayPort output DP1 and is only
converted to HDMI in U7 (an RA620).
Signed-off-by: Torsten Duwe <duwe@lst.de>
[fixed commit subject prefixes]
Link: https://patch.msgid.link/20251110181153.CC62B6732A@verein.lst.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK 5B+/5T USB Type-C port supports Dual Role Data and
should also act as a host. However, currently, when acting as a host,
only self-powered devices work.
Since the ROCK 5B+ supports Dual Role Power, set the power-role
property to "dual" and the try-power-role property to "sink". (along
with related properties)
The ROCK 5T should only support the "source" power-role.
This allows the port to act as a host, supply power to the port, and
allow bus-powered devices to work.
Note that on the ROCK 5T, with this patch applied, it has been
observed that some bus-powered devices do not work correctly. Also,
it has been observed that after connecting a device (and the data-role
switches to host), connecting a host device does not switch the
data-role back to the device role. These issues should be addressed
separately.
Note that there is a separate known issue where USB 3.0 SuperSpeed
devices do not work when oriented in reverse. This issue should also be
addressed separately. (USB 2.0/1.1 devices work in both orientations)
Fixes: 67b2c15d8f ("arm64: dts: rockchip: add USB-C support for ROCK 5B/5B+/5T")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://patch.msgid.link/20251104085227.820-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When the device was first added, there was a problem with the bluetooth
controller that manifested when DMA was enabled for the underlying UART
interface. At some point in the intervening time the problem appears to
have been resolved. Add the UART rx and tx channels back to re-enable
UART.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://patch.msgid.link/20251105205708.732125-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3588 evb2 board has a full size DisplayPort connector, enable
for it.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R76S (as "R76S") is an open-sourced mini IoT gateway
device with two 2.5G, designed and developed by FriendlyElec.
Specification:
- Rockchip RK3576
- 2/4GB LPDDR4X RAM
- 2x 2500Base-T (PCIe, rtl8125b)
- 3x LEDs (Power, LAN, WAN)
- 32GB eMMC
- MicroSD Slot
- MDMI 1.4/2.0 OUT
- M.2 E-Key SDIO slot
- USB 3.0 Port
- USB Type-C 5V Power
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R76S (as "R76S") is an open-sourced mini IoT gateway
device with two 2.5G, designed and developed by FriendlyElec.
Add devicetree binding documentation for the FriendlyElec NanoPi R76S
board.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the Designware MIPI DSI controller and it's port nodes.
Signed-off-by: WeiHao Li <cn.liweihao@gmail.com>
[removed endpoint address, as there is only one vop leading to DSI]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3368 has a InnoSilicon D-PHY which supports DSI/LVDS/TTL with maximum
trasnfer rate of 1 Gbps per lane.
Signed-off-by: WeiHao Li <cn.liweihao@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy()"
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
