Add support for AD7770, AD7771, AD7779 ADCs. The device is capable of
sending out data both on DOUT lines interface,as on the SDO line.
The driver currently implements only the SDO data streaming mode. SPI
communication is used alternatively for accessing registers and streaming
data. Register accesses are protected by crc8.
Signed-off-by: Ramona Alexandra Nechita <ramona.nechita@analog.com>
Link: https://patch.msgid.link/20241014143204.30195-4-ramona.nechita@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, the conversion were triggered by setting high the GPIO
connected to the convst pin. This commit gives the possibility to
connect the convst pin to a PWM.
Connecting a PWM allows to have a better control on the samplerate,
but it must be handled with care, as it is completely decorrelated of
the driver's busy pin handling.
Hence it is not recommended to be used "as is" but must be exploited
in conjunction with IIO backend, and for now only a mock functionality
is enabled, i.e PWM never swings, but is used as a GPIO, i.e duty_cycle
== period equals high state, duty_cycle == 0 equals low state.
This mock functionality will be disabled after the IIO backend usecase
is introduced.
Signed-off-by: Guillaume Stols <gstols@baylibre.com>
Link: https://patch.msgid.link/20241015-ad7606_add_iio_backend_support-v5-4-654faf1ae08c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the required properties for iio-backend support, as well as an
example and the conditions to mutually exclude interruption and
conversion trigger with iio-backend.
The iio-backend's function is to controls the communication, and thus the
interruption pin won't be available anymore.
As a consequence, the conversion pin must be controlled externally since
we will miss information about when every single conversion cycle (i.e
conversion + data transfer) ends, hence a PWM is introduced to trigger
the conversions.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Guillaume Stols <gstols@baylibre.com>
Link: https://patch.msgid.link/20241015-ad7606_add_iio_backend_support-v5-2-654faf1ae08c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We just need the reset gpio during probe so there's no need to keep it
in our state struct. Hence, move devm_gpiod_get_optional() into
ad74413r_reset() and use a local struct gpio_desc.
While at it, request the gpio in the asserted state (GPIOD_OUT_HIGH) so
that we already perform the reset while requesting the gpio saving us a
call to gpiod_set_value_cansleep().
Also, explicitly include <gpio/consumer.h> for
devm_gpiod_get_optional().
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20241016-dev-ad74413r-minor-improv-v1-1-13c9c769237d@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BMP3xx and BMP5xx sensors have an interrupt pin which can be used as
a trigger for when there are data ready in the sensor for pick up.
This use case is used along with NORMAL_MODE in the sensor, which allows
the sensor to do consecutive measurements depending on the ODR rate value.
The trigger pin can be configured to be open-drain or push-pull and either
rising or falling edge.
No support is added yet for interrupts for FIFO, WATERMARK and out of range
values.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://patch.msgid.link/20241017233022.238250-4-vassilisamir@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add forced mode support in sensors BMP28x, BME28x, BMP3xx and BMP58x.
Sensors BMP18x and BMP085 are old and do not support this feature so
their operation is not affected at all.
Essentially, up to now, the rest of the sensors were used in normal mode
all the time. This means that they are continuously doing measurements
even though these measurements are not used. Even though the sensor does
provide PM support, to cover all the possible use cases, the sensor needs
to go into sleep mode and wake up whenever necessary.
The idea is that the sensor is by default in sleep mode, wakes up in
forced mode when a oneshot capture is requested, or in normal mode
when the buffer is enabled. The difference lays in the fact that in
forced mode, the sensor does only one conversion and goes back to sleep
while in normal mode, the sensor does continuous measurements with the
frequency that was set in the ODR registers.
The bmpX_chip_config() functions which are responsible for applying
the requested configuration to the sensor, are modified accordingly
in order to set the sensor by default in sleep mode.
DEEP STANDBY, Low Power NORMAL and CONTINUOUS modes, supported only by
the BMP58x version, are not added.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://patch.msgid.link/20241017233022.238250-2-vassilisamir@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add the iio driver for bosch imu smi240. The smi240 is a combined
three axis angular rate and three axis acceleration sensor module
with a measurement range of +/-300°/s and up to 16g. A synchronous
acc and gyro sampling can be triggered by setting the capture bit
in spi read command.
Implemented features:
* raw data access for each axis through sysfs
* tiggered buffer for continuous sampling
* synchronous acc and gyro data from tiggered buffer
Signed-off-by: Shen Jianping <Jianping.Shen@de.bosch.com>
Link: https://patch.msgid.link/20241018135234.5446-3-Jianping.Shen@de.bosch.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull bluetooth fixes from Luiz Augusto Von Dentz:
- ISO: Fix multiple init when debugfs is disabled
- Call iso_exit() on module unload
- Remove debugfs directory on module init failure
- btusb: Fix not being able to reconnect after suspend
- btusb: Fix regression with fake CSR controllers 0a12:0001
- bnep: fix wild-memory-access in proto_unregister
Note: normally the bluetooth fixes go through the networking tree, but
this missed the weekly merge, and two of the commits fix regressions
that have caused a fair amount of noise and have now hit stable too:
https://lore.kernel.org/all/4e1977ca-6166-4891-965e-34a6f319035f@leemhuis.info/
So I'm pulling it directly just to expedite things and not miss yet
another -rc release. This is not meant to become a new pattern.
* tag 'for-net-2024-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
Bluetooth: bnep: fix wild-memory-access in proto_unregister
Bluetooth: btusb: Fix not being able to reconnect after suspend
Bluetooth: Remove debugfs directory on module init failure
Bluetooth: Call iso_exit() on module unload
Bluetooth: ISO: Fix multiple init when debugfs is disabled
Pull pin control fixes from Linus Walleij:
"Mostly error path fixes, but one pretty serious interrupt problem in
the Ocelot driver as well:
- Fix two error paths and a missing semicolon in the Intel driver
- Add a missing ACPI ID for the Intel Panther Lake
- Check return value of devm_kasprintf() in the Apple and STM32
drivers
- Add a missing mutex_destroy() in the aw9523 driver
- Fix a double free in cv1800_pctrl_dt_node_to_map() in the Sophgo
driver
- Fix a double free in ma35_pinctrl_dt_node_to_map_func() in the
Nuvoton driver
- Fix a bug in the Ocelot interrupt handler making the system hang"
* tag 'pinctrl-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: ocelot: fix system hang on level based interrupts
pinctrl: nuvoton: fix a double free in ma35_pinctrl_dt_node_to_map_func()
pinctrl: sophgo: fix double free in cv1800_pctrl_dt_node_to_map()
pinctrl: intel: platform: Add Panther Lake to the list of supported
pinctrl: aw9523: add missing mutex_destroy
pinctrl: stm32: check devm_kasprintf() returned value
pinctrl: apple: check devm_kasprintf() returned value
pinctrl: intel: platform: use semicolon instead of comma in ncommunities assignment
pinctrl: intel: platform: fix error path in device_for_each_child_node()
Pull misc driver fixes from Greg KH:
"Here are a number of small char/misc/iio driver fixes for 6.12-rc4:
- loads of small iio driver fixes for reported problems
- parport driver out-of-bounds fix
- Kconfig description and MAINTAINERS file updates
All of these, except for the Kconfig and MAINTAINERS file updates have
been in linux-next all week. Those other two are just documentation
changes and will have no runtime issues and were merged on Friday"
* tag 'char-misc-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (39 commits)
misc: rtsx: list supported models in Kconfig help
MAINTAINERS: Remove some entries due to various compliance requirements.
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for OTP device
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for EEPROM device
parport: Proper fix for array out-of-bounds access
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.12-rc4:
- qcom-geni serial driver fixes, wow what a mess of a UART chip that
thing is...
- vt infoleak fix for odd font sizes
- imx serial driver bugfix
- yet-another n_gsm ldisc bugfix, slowly chipping down the issues in
that piece of code
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: qcom-geni: rename suspend functions
serial: qcom-geni: drop unused receive parameter
serial: qcom-geni: drop flip buffer WARN()
serial: qcom-geni: fix rx cancel dma status bit
serial: qcom-geni: fix receiver enable
serial: qcom-geni: fix dma rx cancellation
serial: qcom-geni: fix shutdown race
serial: qcom-geni: revert broken hibernation support
serial: qcom-geni: fix polled console initialisation
serial: imx: Update mctrl old_status on RTSD interrupt
tty: n_gsm: Fix use-after-free in gsm_cleanup_mux
vt: prevent kernel-infoleak in con_font_get()
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 6.12-rc4:
- xhci driver fixes for a number of reported issues
- new usb-serial driver ids
- dwc3 driver fixes for reported problems.
- usb gadget driver fixes for reported problems
- typec driver fixes
- MAINTAINER file updates
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
xhci: dbc: honor usb transfer size boundaries.
usb: xhci: Fix handling errors mid TD followed by other errors
xhci: Mitigate failed set dequeue pointer commands
xhci: Fix incorrect stream context type macro
USB: gadget: dummy-hcd: Fix "task hung" problem
usb: gadget: f_uac2: fix return value for UAC2_ATTRIBUTE_STRING store
usb: dwc3: core: Fix system suspend on TI AM62 platforms
xhci: tegra: fix checked USB2 port number
usb: dwc3: Wait for EndXfer completion before restoring GUSB2PHYCFG
usb: typec: qcom-pmic-typec: fix sink status being overwritten with RP_DEF
usb: typec: altmode should keep reference to parent
MAINTAINERS: usb: raw-gadget: add bug tracker link
MAINTAINERS: Add an entry for the LJCA drivers
Pull x86 fixes from Borislav Petkov:
- Explicitly disable the TSC deadline timer when going idle to address
some CPU errata in that area
- Do not apply the Zenbleed fix on anything else except AMD Zen2 on the
late microcode loading path
- Clear CPU buffers later in the NMI exit path on 32-bit to avoid
register clearing while they still contain sensitive data, for the
RDFS mitigation
- Do not clobber EFLAGS.ZF with VERW on the opportunistic SYSRET exit
path on 32-bit
- Fix parsing issues of memory bandwidth specification in sysfs for
resctrl's memory bandwidth allocation feature
- Other small cleanups and improvements
* tag 'x86_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Always explicitly disarm TSC-deadline timer
x86/CPU/AMD: Only apply Zenbleed fix for Zen2 during late microcode load
x86/bugs: Use code segment selector for VERW operand
x86/entry_32: Clear CPU buffers after register restore in NMI return
x86/entry_32: Do not clobber user EFLAGS.ZF
x86/resctrl: Annotate get_mem_config() functions as __init
x86/resctrl: Avoid overflow in MB settings in bw_validate()
x86/amd_nb: Add new PCI ID for AMD family 1Ah model 20h
Pull irq fixes from Borislav Petkov:
- Fix a case for sifive-plic where an interrupt gets disabled *and*
masked and remains masked when it gets reenabled later
- Plug a small race in GIC-v4 where userspace can force an affinity
change of a virtual CPU (vPE) in its unmapping path
- Do not mix the two sets of ocelot irqchip's registers in the mask
calculation of the main interrupt sticky register
- Other smaller fixlets and cleanups
* tag 'irq_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/renesas-rzg2l: Fix missing put_device
irqchip/riscv-intc: Fix SMP=n boot with ACPI
irqchip/sifive-plic: Unmask interrupt in plic_irq_enable()
irqchip/gic-v4: Don't allow a VMOVP on a dying VPE
irqchip/sifive-plic: Return error code on failure
irqchip/riscv-imsic: Fix output text of base address
irqchip/ocelot: Comment sticky register clearing code
irqchip/ocelot: Fix trigger register address
irqchip: Remove obsolete config ARM_GIC_V3_ITS_PCI
Pull scheduling fixes from Borislav Petkov:
- Add PREEMPT_RT maintainers
- Fix another aspect of delayed dequeued tasks wrt determining their
state, i.e., whether they're runnable or blocked
- Handle delayed dequeued tasks and their migration wrt PSI properly
- Fix the situation where a delayed dequeue task gets enqueued into a
new class, which should not happen
- Fix a case where memory allocation would happen while the runqueue
lock is held, which is a no-no
- Do not over-schedule when tasks with shorter slices preempt the
currently running task
- Make sure delayed to deque entities are properly handled before
unthrottling
- Other smaller cleanups and improvements
* tag 'sched_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Add an entry for PREEMPT_RT.
sched/fair: Fix external p->on_rq users
sched/psi: Fix mistaken CPU pressure indication after corrupted task state bug
sched/core: Dequeue PSI signals for blocked tasks that are delayed
sched: Fix delayed_dequeue vs switched_from_fair()
sched/core: Disable page allocation in task_tick_mm_cid()
sched/deadline: Use hrtick_enabled_dl() before start_hrtick_dl()
sched/eevdf: Fix wakeup-preempt by checking cfs_rq->nr_running
sched: Fix sched_delayed vs cfs_bandwidth
Pull xen fix from Juergen Gross:
"A single fix for a build failure introduced this merge window"
* tag 'for-linus-6.12a-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Remove dependency between pciback and privcmd
Pull dma-mapping fix from Christoph Hellwig:
"Just another small tracing fix from Sean"
* tag 'dma-mapping-6.12-2024-10-20' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix tracing dma_alloc/free with vmalloc'd memory
Pull one more io_uring fix from Jens Axboe:
"Fix for a regression introduced in 6.12-rc2, where a condition check
was negated and hence -EAGAIN would bubble back up up to userspace
rather than trigger a retry condition"
* tag 'io_uring-6.12-20241019' of git://git.kernel.dk/linux:
io_uring/rw: fix wrong NOWAIT check in io_rw_init_file()
Pull SCSI fixes from James Bottomley:
"Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Fix null-ptr-deref in target_alloc_device()
scsi: mpi3mr: Validate SAS port assignments
scsi: ufs: core: Set SDEV_OFFLINE when UFS is shut down
scsi: ufs: core: Requeue aborted request
scsi: ufs: core: Fix the issue of ICU failure
Pull ftrace fixes from Steven Rostedt:
"A couple of fixes to function graph infrastructure:
- Fix allocation of idle shadow stack allocation during hotplug
If function graph tracing is started when a CPU is offline, if it
were come online during the trace then the idle task that
represents the CPU will not get a shadow stack allocated for it.
This means all function graph hooks that happen while that idle
task is running (including in interrupt mode) will have all its
events dropped.
Switch over to the CPU hotplug mechanism that will have any newly
brought on line CPU get a callback that can allocate the shadow
stack for its idle task.
- Fix allocation size of the ret_stack_list array
When function graph tracing converted over to allowing more than
one user at a time, it had to convert its shadow stack from an
array of ret_stack structures to an array of unsigned longs. The
shadow stacks are allocated in batches of 32 at a time and assigned
to every running task. The batch is held by the ret_stack_list
array.
But when the conversion happened, instead of allocating an array of
32 pointers, it was allocated as a ret_stack itself (PAGE_SIZE).
This ret_stack_list gets passed to a function that iterates over
what it believes is its size defined by the
FTRACE_RETSTACK_ALLOC_SIZE macro (which is 32).
Luckily (PAGE_SIZE) is greater than 32 * sizeof(long), otherwise
this would have been an array overflow. This still should be fixed
and the ret_stack_list should be allocated to the size it is
expected to be as someday it may end up being bigger than
SHADOW_STACK_SIZE"
* tag 'ftrace-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
fgraph: Allocate ret_stack_list with proper size
fgraph: Use CPU hotplug mechanism to initialize idle shadow stacks
Pull ipe fixes from Fan Wu:
"This addresses several issues identified by Luca when attempting to
enable IPE on Debian and systemd:
- address issues with IPE policy update errors and policy update
version check, improving the clarity of error messages for better
understanding by userspace programs.
- enable IPE policies to be signed by secondary and platform
keyrings, facilitating broader use across general Linux
distributions like Debian.
- updates the IPE entry in the MAINTAINERS file to reflect the new
tree URL and my updated email from kernel.org"
* tag 'ipe-pr-20241018' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe:
MAINTAINERS: update IPE tree url and Fan Wu's email
ipe: fallback to platform keyring also if key in trusted keyring is rejected
ipe: allow secondary and platform keyrings to install/update policies
ipe: also reject policy updates with the same version
ipe: return -ESTALE instead of -EINVAL on update when new policy has a lower version
Pull input fixes from Dmitry Torokhov:
- a fix for Zinitix driver to not fail probing if the property enabling
touch keys functionality is not defined. Support for touch keys was
added in 6.12 merge window so this issue does not affect users of
released kernels
- a couple new vendor/device IDs in xpad driver to enable support for
more hardware
* tag 'input-for-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: zinitix - don't fail if linux,keycodes prop is absent
Input: xpad - add support for MSI Claw A1M
Input: xpad - add support for 8BitDo Ultimate 2C Wireless Controller
