Set ENABLE_L2_EXIT_RATE_CHANGE register bit to request UPHY PLL rate change
to Gen1 during initialization. This helps in the below surprise link down
cases,
- Surprise link down happens at Gen3/Gen4 link speed.
- Surprise link down happens and external REFCLK is cut off, which causes
UPHY PLL rate to deviate to an invalid rate.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://lore.kernel.org/r/20221013183854.21087-9-vidyas@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-15-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-13-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
for MSM8996 as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant configuration
options while increasing the unnecessarily low timer slack somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
But as the vendor kernel do have a 1 ms delay *after* starting the PHY
and before starting to poll the status it is possible that later
contributors have simply not noticed that the mainline power-down delay
is not equivalent.
As the current delay before even starting the PHY is pretty much
pointless and likely a mistake, move the delay after starting the PHY
which avoids a few iterations of polling and speeds up startup by 1 ms
(the poll loop otherwise takes about 1.8 ms).
Note that MSM8998 has never used a power-down delay so add a flag to
skip the delay in case starting the PHY is faster on MSM8998. This can
be removed after someone takes a measurement.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012081241.18273-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-9-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 0d58280cf1 ("phy: Update PHY power control sequence") the
PHY is powered on before configuring the registers and only the MSM8996
PCIe PHY, which includes the POWER_DOWN_CONTROL register in its PCS
initialisation table, may possibly require a second update afterwards.
To make things worse, the POWER_DOWN_CONTROL register lies at a
different offset on more recent SoCs so that the second update, which
still used a hard-coded offset, would write to an unrelated register
(e.g. a revision-id register on SC8280XP).
As the MSM8996 PCIe PHY is now handled by a separate driver, simply drop
the bogus register update.
Fixes: e4d8b05ad5 ("phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB") added support
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #RB3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221017065013.19647-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe QMP PHY requires different programming sequences when being
used for the RC (Root Complex) or for the EP (End Point) modes. Allow
selecting the submode and thus selecting a set of PHY programming
tables.
Since the RC and EP modes share common some common init sequence, the
common sequence is kept in the main table and the sequence differences
are pushed to the extra tables.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220927092207.161501-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8250 configuration tables are split into two parts: the common one and
the PHY-specific tables. Make this split more formal. Rather than having
a blind renamed copy of all QMP table fields, add separate struct
qmp_phy_cfg_tables and add two instances of this structure to the struct
qmp_phy_cfg. Later on this will be used to support different PHY modes
(RC vs EP).
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220927092207.161501-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Turris MOX board with older ARM Trusted Firmware version v1.5 is not able
to detect any USB 3.0 device connected to USB-A port on Mox-A module after
commit 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken
reset support"). On the other hand USB 2.0 devices connected to the same
USB-A port are working fine.
It looks as if the older firmware configures COMPHY registers for USB 3.0
somehow incompatibly for kernel driver. Experiments show that resetting
COMPHY registers via setting SFT_RST auto-clearing bit in COMPHY_SFT_RESET
register fixes this issue.
Reset the COMPHY in mvebu_a3700_comphy_usb3_power_on() function as a first
step after selecting COMPHY lane and USB 3.0 function. With this change
Turris MOX board can successfully detect USB 3.0 devices again.
Before the above mentioned commit this reset was implemented in PHY reset
method, so this is the reason why there was no issue with older firmware
version then.
Fixes: 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20220920121154.30115-1-pali@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
