Codewise there is no difference between these two, so it does not make
sense to treat them differently. Also chip families having one of these
tend to have the other.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6247/
Instead of treating each flavour as an exclusive CPU to select, make
BMIPS the only option and let SYS_HAS_CPU_BMIPS* decide for which
flavours to include support.
Run tested on BMIPS3300 and BMIPS4350, only build tested for BMIPS4380
and BMIPS5000.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6240/
Allow building for all bmips cpus at the same time by changing ifdefs
to checks for the cpu type, or adding appropriate checks to the
assembly.
Since BMIPS43XX and BMIPS5000 require different IPI implementations,
split the SMP ops into one for each, so the runtime overhead is only
at registration time for them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6241/
CPUs implementing MIPS32 R2 may include a 64-bit FPU, just as MIPS64 CPUs
do. In order to preserve backwards compatibility a 64-bit FPU will act
like a 32-bit FPU (by accessing doubles from the least significant 32
bits of an even-odd pair of FP registers) when the Status.FR bit is
zero, again just like a mips64 CPU. The standard O32 ABI is defined
expecting a 32-bit FPU, however recent toolchains support use of a
64-bit FPU from an O32 MIPS32 executable. When an ELF executable is
built to use a 64-bit FPU a new flag (EF_MIPS_FP64) is set in the ELF
header.
With this patch the kernel will check the EF_MIPS_FP64 flag when
executing an O32 binary, and set Status.FR accordingly. The addition
of O32 64-bit FP support lessens the opportunity for optimisation in
the FPU emulator, so a CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option is
introduced to allow this support to be disabled for those that don't
require it.
Inspired by an earlier patch by Leonid Yegoshin, but implemented more
cleanly & correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6154/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the mfhc1 & mthc1 instructions to the FPU
emulator. These instructions were introduced in release 2 of the MIPS32
& MIPS64 architectures and allow access to the most significant 32 bits
of a 64-bit FP register.
[ralf@linux-mips.org: Fix ifdef hell added by original patch.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While running stress tests on adding and deleting ftrace instances I hit
this bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: selinux_inode_permission+0x85/0x160
PGD 63681067 PUD 7ddbe067 PMD 0
Oops: 0000 [#1] PREEMPT
CPU: 0 PID: 5634 Comm: ftrace-test-mki Not tainted 3.13.0-rc4-test-00033-gd2a6dde-dirty #20
Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
task: ffff880078375800 ti: ffff88007ddb0000 task.ti: ffff88007ddb0000
RIP: 0010:[<ffffffff812d8bc5>] [<ffffffff812d8bc5>] selinux_inode_permission+0x85/0x160
RSP: 0018:ffff88007ddb1c48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000800000 RCX: ffff88006dd43840
RDX: 0000000000000001 RSI: 0000000000000081 RDI: ffff88006ee46000
RBP: ffff88007ddb1c88 R08: 0000000000000000 R09: ffff88007ddb1c54
R10: 6e6576652f6f6f66 R11: 0000000000000003 R12: 0000000000000000
R13: 0000000000000081 R14: ffff88006ee46000 R15: 0000000000000000
FS: 00007f217b5b6700(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033^M
CR2: 0000000000000020 CR3: 000000006a0fe000 CR4: 00000000000007f0
Call Trace:
security_inode_permission+0x1c/0x30
__inode_permission+0x41/0xa0
inode_permission+0x18/0x50
link_path_walk+0x66/0x920
path_openat+0xa6/0x6c0
do_filp_open+0x43/0xa0
do_sys_open+0x146/0x240
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
Code: 84 a1 00 00 00 81 e3 00 20 00 00 89 d8 83 c8 02 40 f6 c6 04 0f 45 d8 40 f6 c6 08 74 71 80 cf 02 49 8b 46 38 4c 8d 4d cc 45 31 c0 <0f> b7 50 20 8b 70 1c 48 8b 41 70 89 d9 8b 78 04 e8 36 cf ff ff
RIP selinux_inode_permission+0x85/0x160
CR2: 0000000000000020
Investigating, I found that the inode->i_security was NULL, and the
dereference of it caused the oops.
in selinux_inode_permission():
isec = inode->i_security;
rc = avc_has_perm_noaudit(sid, isec->sid, isec->sclass, perms, 0, &avd);
Note, the crash came from stressing the deletion and reading of debugfs
files. I was not able to recreate this via normal files. But I'm not
sure they are safe. It may just be that the race window is much harder
to hit.
What seems to have happened (and what I have traced), is the file is
being opened at the same time the file or directory is being deleted.
As the dentry and inode locks are not held during the path walk, nor is
the inodes ref counts being incremented, there is nothing saving these
structures from being discarded except for an rcu_read_lock().
The rcu_read_lock() protects against freeing of the inode, but it does
not protect freeing of the inode_security_struct. Now if the freeing of
the i_security happens with a call_rcu(), and the i_security field of
the inode is not changed (it gets freed as the inode gets freed) then
there will be no issue here. (Linus Torvalds suggested not setting the
field to NULL such that we do not need to check if it is NULL in the
permission check).
Note, this is a hack, but it fixes the problem at hand. A real fix is
to restructure the destroy_inode() to call all the destructor handlers
from the RCU callback. But that is a major job to do, and requires a
lot of work. For now, we just band-aid this bug with this fix (it
works), and work on a more maintainable solution in the future.
Link: http://lkml.kernel.org/r/20140109101932.0508dec7@gandalf.local.home
Link: http://lkml.kernel.org/r/20140109182756.17abaaa8@gandalf.local.home
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We see General Protection Fault on RSI in copy_page_rep: that RSI is
what you get from a NULL struct page pointer.
RIP: 0010:[<ffffffff81154955>] [<ffffffff81154955>] copy_page_rep+0x5/0x10
RSP: 0000:ffff880136e15c00 EFLAGS: 00010286
RAX: ffff880000000000 RBX: ffff880136e14000 RCX: 0000000000000200
RDX: 6db6db6db6db6db7 RSI: db73880000000000 RDI: ffff880dd0c00000
RBP: ffff880136e15c18 R08: 0000000000000200 R09: 000000000005987c
R10: 000000000005987c R11: 0000000000000200 R12: 0000000000000001
R13: ffffea00305aa000 R14: 0000000000000000 R15: 0000000000000000
FS: 00007f195752f700(0000) GS:ffff880c7fc20000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000093010000 CR3: 00000001458e1000 CR4: 00000000000027e0
Call Trace:
copy_user_huge_page+0x93/0xab
do_huge_pmd_wp_page+0x710/0x815
handle_mm_fault+0x15d8/0x1d70
__do_page_fault+0x14d/0x840
do_page_fault+0x2f/0x90
page_fault+0x22/0x30
do_huge_pmd_wp_page() tests is_huge_zero_pmd(orig_pmd) four times: but
since shrink_huge_zero_page() can free the huge_zero_page, and we have
no hold of our own on it here (except where the fourth test holds
page_table_lock and has checked pmd_same), it's possible for it to
answer yes the first time, but no to the second or third test. Change
all those last three to tests for NULL page.
(Note: this is not the same issue as trinity's DEBUG_PAGEALLOC BUG
in copy_page_rep with RSI: ffff88009c422000, reported by Sasha Levin
in https://lkml.org/lkml/2013/3/29/103. I believe that one is due
to the source page being split, and a tail page freed, while copy
is in progress; and not a problem without DEBUG_PAGEALLOC, since
the pmd_same check will prevent a miscopy from being made visible.)
Fixes: 97ae17497e ("thp: implement refcounting for huge zero page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # v3.10 v3.11 v3.12
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When queue_mode is NULL_Q_MQ and null_blk is being removed,
blk_cleanup_queue() isn't called to cleanup queue, so the queue
allocated won't be freed.
This patch calls blk_cleanup_queue() for MQ to drain all pending
requests first and release the reference counter of queue kobject, then
blk_mq_free_queue() will be called in queue kobject's release handler
when queue kobject's reference counter drops to zero.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"Famouse last words: "final pull request" :-)
I'm sending this because Jason Wang's fixes are pretty important
1) Add missing per-cpu stats initialization to ip6_vti. Otherwise
lockdep spits out a call trace. From Li RongQing.
2) Fix NULL oops in wireless hwsim, from Javier Lopez
3) TIPC deferred packet queue unlink must NULL out skb->next to avoid
crashes. From Erik Hugne
4) Fix access to uninitialized buffer in nf_nat netfilter code, from
Daniel Borkmann
5) Fix lifetime of ipv6 loopback and SIT tunnel addresses, otherwise
they basically timeout immediately. From Hannes Frederic Sowa
6) Fix DMA unmapping of TSO packets in bnx2x driver, from Michal
Schmidt
7) Do not allow L2 forwarding offload via macvtap device, the way
things are now it will not end up being forwaded at all. From
Jason Wang
8) Fix transmit queue selection via ndo_dfwd_start_xmit(), fixing
things like applying NETIF_F_LLTX to the wrong device (!!) and
eliding the proper transmit watchdog handling
9) qlcnic driver was not updating tx statistics at all, from Manish
Chopra"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
qlcnic: Fix ethtool statistics length calculation
qlcnic: Fix bug in TX statistics
net: core: explicitly select a txq before doing l2 forwarding
macvlan: forbid L2 fowarding offload for macvtap
bnx2x: fix DMA unmapping of TSO split BDs
ipv6: add link-local, sit and loopback address with INFINITY_LIFE_TIME
bnx2x: prevent WARN during driver unload
tipc: correctly unlink packets from deferred packet queue
ipv6: pcpu_tstats.syncp should be initialised in ip6_vti.c
netfilter: only warn once on wrong seqadj usage
netfilter: nf_nat: fix access to uninitialized buffer in IRC NAT helper
NFC: Fix target mode p2p link establishment
iwlwifi: add new devices for 7265 series
mac80211: move "bufferable MMPDU" check to fix AP mode scan
mac80211_hwsim: Fix NULL pointer dereference
Pull xfs bugfixes from Ben Myers:
"Here we have a bugfix for an off-by-one in the remote attribute
verifier that results in a forced shutdown which you can hit with v5
superblock by creating a 64k xattr, and a fix for a missing
destroy_work_on_stack() in the allocation worker.
It's a bit late, but they are both fairly straightforward"
* tag 'xfs-for-linus-v3.13-rc8' of git://oss.sgi.com/xfs/xfs:
xfs: Calling destroy_work_on_stack() to pair with INIT_WORK_ONSTACK()
xfs: fix off-by-one error in xfs_attr3_rmt_verify
Pull LED fix from Bryan Wu:
"Pali Rohár and Pavel Machek reported the LED of Nokia N900 doesn't
work with our latest 3.13-rc6 kernel. Milo fixed the regression here"
* 'leds-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp5521/5523: Remove duplicate mutex
Pull ACPI and power management fixes from Rafael Wysocki:
- Recent commits modifying the lists of C-states in the intel_idle
driver introduced bugs leading to crashes on some systems. Two fixes
from Jiang Liu.
- The ACPI AC driver should receive all types of notifications, but
recent change made it ignore some of them. Fix from Alexander Mezin.
- intel_pstate's validity checks for MSRs it depends on are not
sufficient to catch the lack of support in nested KVM setups, so they
are extended to cover that case. From Dirk Brandewie.
- NEC LZ750/LS has a botched up _BIX method in its ACPI tables, so our
ACPI battery driver needs a quirk for it. From Lan Tianyu.
- The tpm_ppi driver sometimes leaks memory allocated by
acpi_get_name(). Fix from Jiang Liu.
* tag 'pm+acpi-3.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: close avn_cstates array with correct marker
Revert "intel_idle: mark states tables with __initdata tag"
ACPI / Battery: Add a _BIX quirk for NEC LZ750/LS
intel_pstate: Add X86_FEATURE_APERFMPERF to cpu match parameters.
ACPI / TPM: fix memory leak when walking ACPI namespace
ACPI / AC: change notification handler type to ACPI_ALL_NOTIFY
Pull MFD fix from Samuel Ortiz:
"This is the 2nd MFD pull request for 3.13
It only contains one fix for the rtsx_pcr driver. Without it we see a
kernel panic on some machines, when resuming from suspend to RAM"
* tag 'mfd-fixes-3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: rtsx_pcr: Disable interrupts before cancelling delayed works
It can be a problem when a pattern is loaded via the firmware interface.
LP55xx common driver has already locked the mutex in 'lp55xx_firmware_loaded()'.
So it should be deleted.
On the other hand, locks are required in store_engine_load()
on updating program memory.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Cc: <stable@vger.kernel.org>
In case CONFIG_DEBUG_OBJECTS_WORK is defined, it is needed to
call destroy_work_on_stack() which frees the debug object to pair
with INIT_WORK_ONSTACK().
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 6f96b3063c)
With CRC check is enabled, if trying to set an attributes value just
equal to the maximum size of XATTR_SIZE_MAX would cause the v3 remote
attr write verification procedure failure, which would yield the back
trace like below:
<snip>
XFS (sda7): Internal error xfs_attr3_rmt_write_verify at line 191 of file fs/xfs/xfs_attr_remote.c
<snip>
Call Trace:
[<ffffffff816f0042>] dump_stack+0x45/0x56
[<ffffffffa0d99c8b>] xfs_error_report+0x3b/0x40 [xfs]
[<ffffffffa0d96edd>] ? _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffffa0d99ce5>] xfs_corruption_error+0x55/0x80 [xfs]
[<ffffffffa0dbef6b>] xfs_attr3_rmt_write_verify+0x14b/0x1a0 [xfs]
[<ffffffffa0d96edd>] ? _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffffa0d97315>] ? xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d96edd>] _xfs_buf_ioapply+0x6d/0x390 [xfs]
[<ffffffff81184cda>] ? vm_map_ram+0x31a/0x460
[<ffffffff81097230>] ? wake_up_state+0x20/0x20
[<ffffffffa0d97315>] ? xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d9726b>] xfs_buf_iorequest+0x6b/0xc0 [xfs]
[<ffffffffa0d97315>] xfs_bdstrat_cb+0x55/0xb0 [xfs]
[<ffffffffa0d97906>] xfs_bwrite+0x46/0x80 [xfs]
[<ffffffffa0dbfa94>] xfs_attr_rmtval_set+0x334/0x490 [xfs]
[<ffffffffa0db84aa>] xfs_attr_leaf_addname+0x24a/0x410 [xfs]
[<ffffffffa0db8893>] xfs_attr_set_int+0x223/0x470 [xfs]
[<ffffffffa0db8b76>] xfs_attr_set+0x96/0xb0 [xfs]
[<ffffffffa0db13b2>] xfs_xattr_set+0x42/0x70 [xfs]
[<ffffffff811df9b2>] generic_setxattr+0x62/0x80
[<ffffffff811e0213>] __vfs_setxattr_noperm+0x63/0x1b0
[<ffffffff81307afe>] ? evm_inode_setxattr+0xe/0x10
[<ffffffff811e0415>] vfs_setxattr+0xb5/0xc0
[<ffffffff811e054e>] setxattr+0x12e/0x1c0
[<ffffffff811c6e82>] ? final_putname+0x22/0x50
[<ffffffff811c708b>] ? putname+0x2b/0x40
[<ffffffff811cc4bf>] ? user_path_at_empty+0x5f/0x90
[<ffffffff811bdfd9>] ? __sb_start_write+0x49/0xe0
[<ffffffff81168589>] ? vm_mmap_pgoff+0x99/0xc0
[<ffffffff811e07df>] SyS_setxattr+0x8f/0xe0
[<ffffffff81700c2d>] system_call_fastpath+0x1a/0x1f
Tests:
setfattr -n user.longxattr -v `perl -e 'print "A"x65536'` testfile
This patch fix it to check the remote EA size is greater than the
XATTR_SIZE_MAX rather than more than or equal to it, because it's
valid if the specified EA value size is equal to the limitation as
per VFS setxattr interface.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 85dd0707f0)
o Consider number of Tx queues while calculating the length of
Tx statistics as part of ethtool stats.
o Calculate statistics lenght properly for 82xx and 83xx adapter
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not updating TX stats so it was not populating
statistics in `ifconfig` command output.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 fowarding offload will bypass the rx handler of real device. This will make
the packet could not be forwarded to macvtap device. Another problem is the
dev_hard_start_xmit() called for macvtap does not have any synchronization.
Fix this by forbidding L2 forwarding for macvtap.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
For the mac80211 bits, Johannes says:
"I have a fix from Javier for mac80211_hwsim when used with wmediumd
userspace, and a fix from Felix for buffering in AP mode."
For the NFC bits, Samuel says:
"This pull request only contains one fix for a regression introduced with
commit e29a9e2ae1. Without this fix, we can not establish a p2p link
in target mode. Only initiator mode works."
For the iwlwifi bits, Emmanuel says:
"It only includes new device IDs so it's not vital. If you have a pull
request to net.git anyway, I'd happy to have this in."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x triggers warnings with CONFIG_DMA_API_DEBUG=y:
WARNING: CPU: 0 PID: 2253 at lib/dma-debug.c:887 check_unmap+0xf8/0x920()
bnx2x 0000:28:00.0: DMA-API: device driver frees DMA memory with
different size [device address=0x00000000da2b389e] [map size=1490 bytes]
[unmap size=66 bytes]
The reason is that bnx2x splits a TSO BD into two BDs (headers + data)
using one DMA mapping for both, but it uses only the length of the first
BD when unmapping.
This patch fixes the bug by unmapping the whole length of the two BDs.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull clock fixes from Mike Turquette:
"Late fixes for clock drivers. All of these fixes are for user-visible
regressions, typically boot failures or other unsafe system
configuration that causes badness"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: clk-divider: fix divisor > 255 bug
clk: exynos: File scope reg_save array should depend on PM_SLEEP
clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg clock
ARM: dts: exynos5250: Fix MDMA0 clock number
clk: samsung: exynos5250: Add MDMA0 clocks
clk: samsung: exynos5250: Fix ACP gate register offset
clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
clk: samsung: exynos4: Correct SRC_MFC register
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for Renesas platforms to fixup DMA masks (this started
causing errors once the DMA API added checks for valid masks in 3.13)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
In the past the IFA_PERMANENT flag indicated, that the valid and preferred
lifetime where ignored. Since change fad8da3e08 ("ipv6 addrconf: fix
preferred lifetime state-changing behavior while valid_lft is infinity")
we honour at least the preferred lifetime on those addresses. As such
the valid lifetime gets recalculated and updated to 0.
If loopback address is added manually this problem does not occur.
Also if NetworkManager manages IPv6, those addresses will get added via
inet6_rtm_newaddr and thus will have a correct lifetime, too.
Reported-by: François-Xavier Le Bail <fx.lebail@yahoo.com>
Reported-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: fad8da3e08 ("ipv6 addrconf: fix preferred lifetime state-changing behavior while valid_lft is infinity")
Cc: Yasushi Asano <yasushi.asano@jp.fujitsu.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 80c33dd "net: add might_sleep() call to napi_disable"
bnx2x fails the might_sleep tests causing a stack trace to appear whenever
the driver is unloaded, as local_bh_disable() is being called before
napi_disable().
This changes the locking schematics related to CONFIG_NET_RX_BUSY_POLL,
preventing the need for calling local_bh_disable() and thus eliminating
the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Close avn_cstates array with correct marker to avoid overflow
in function intel_idle_cpu_init().
[rjw: The problem was introduced when commit 22e580d07f was merged
on top of eba682a5ae (intel_idle: shrink states tables).]
Fixes: 22e580d07f (intel_idle: Fixed C6 state on Avoton/Rangeley processors)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull parisc fix from Helge Deller:
"This patch fixes the kmap/kunmap implementation on parisc and finally
makes AIO work on parisc"
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Ensure full cache coherency for kmap/kunmap
Pull libata fixes from Tejun Heo:
"Late fixes for libata. Nothing too interesting. Adding missing PM
callbacks to satat_sis and an additional PCI ID for ahci"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_sis: missing PM support
ahci: add PCI ID for Marvell 88SE9170 SATA controller
Helge Deller noted a few weeks ago problems with the AIO support on
parisc. This change is the result of numerous iterations on how best to
deal with this problem.
The solution adopted here is to provide full cache coherency in a
uniform manner on all parisc systems. This involves calling
flush_dcache_page() on kmap operations and flush_kernel_dcache_page() on
kunmap operations. As a result, the copy_user_page() and
clear_user_page() functions can be removed and the overall code is
simpler.
The change ensures that both userspace and kernel aliases to a mapped
page are invalidated and flushed. This is necessary for the correct
operation of PA8800 and PA8900 based systems which do not support
inequivalent aliases.
With this change, I have observed no cache related issues on c8000 and
rp3440. It is now possible for example to do kernel builds with "-j64"
on four way systems.
On systems using XFS file systems, the patch recently posted by Mikulas
Patocka to "fix crash using XFS on loopback" is needed to avoid a hang
caused by an uninitialized lock passed to flush_dcache_page() in the
page struct.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC fixes pull request for 3.13.
It only contains one fix for a regression introduced with commit
e29a9e2ae1. Without this fix, we can not establish a p2p link in
target mode. Only initiator mode works."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 6d9252bd9a (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
