Originally an explicit ID for the AXP313/AXP323 regulator was set to
avoid a conflict with the primary AXP717 PMIC on Allwinner A523 family
boards.
This didn't entirely work since on some or all of these boards, the
interrupt line on this secondary PMIC was left unconnected, and thus
the driver would fall back to the generic "no interrupt; only regulators"
case, which didn't have the explicit ID set, thus undoing the intended
fix.
Also set an explicit ID for the regulator cell in the no IRQ generic
fall back case. This fixes the conflict for the AXP717 + AXP313/AXP323
case. For the actual single PMIC with no IRQ connected case, the ID does
not affect functionality, only the device naming of the regulator cell,
and by extension the name and path under sysfs.
Fixes: 249abf9b1e25 ("mfd: axp20x: Set explicit ID for AXP313 regulator")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250701163652.252010-1-wens@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The RK806 PMIC has a bitfield for configuring the restart/reset behavior
(which I assume Rockchip calls "function") whenever the PMIC is reset
either programmatically (c.f. DEV_RST in the datasheet) or via PWRCTRL
or RESETB pins.
For RK806, the following values are possible for RST_FUN:
0b00 means "Restart PMU"
0b01 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode"
0b10 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode, and simultaneously
pull down the RESETB PIN for 5mS before releasing"
0b11 means the same as for 0b10 just above.
This adds the appropriate logic in the driver to parse the new
rockchip,reset-mode DT property to pass this information. It just
happens that the values in the binding match the values to write in the
bitfield so no mapping is necessary.
If it is missing, the register is left untouched and relies either on
the silicon default or on whatever was set earlier in the boot stages
(e.g. the bootloader).
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250627-rk8xx-rst-fun-v4-2-ce05d041b45f@cherry.de
Signed-off-by: Lee Jones <lee@kernel.org>
The RK806 PMIC allows to configure its reset/restart behavior whenever
the PMIC is reset either programmatically or via some external pins
(e.g. PWRCTRL or RESETB).
The following modes exist:
- 0; restart PMU,
- 1; reset all power off reset registers and force state to switch to
ACTIVE mode,
- 2; same as mode 1 and also pull RESETB pin down for 5ms,
For example, some hardware may require a full restart (mode 0) in order
to function properly as regulators are shortly interrupted in this mode.
This is the case for RK3588 Jaguar and RK3588 Tiger which have a
companion microcontroller running on an independent power supply and
monitoring the PMIC power rail to know the state of the main system.
When it detects a restart, it resets its own IPs exposed to the main
system as if to simulate its own reset. Failing to perform this fake
reset of the microcontroller may break things (e.g. watchdog not
automatically disabled, buzzer still running until manually disabled,
leftover configuration from previous main system state, etc...).
Some other systems may be depending on the power rails to not be
interrupted even for a small amount of time[1].
This allows to specify how the PMIC should perform on the hardware level
and may differ between hardware designs, so a DT property seems
warranted. I unfortunately do not see how this could be made generic
enough to make it a non-vendor property.
[1] https://lore.kernel.org/linux-rockchip/2577051.irdbgypaU6@workhorse/
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250627-rk8xx-rst-fun-v4-1-ce05d041b45f@cherry.de
Signed-off-by: Lee Jones <lee@kernel.org>
'struct regmap_irq_sub_irq_map' and 'struct tps65219_chip_data' are not
modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
27804 10016 256 38076 94bc drivers/mfd/tps65219.o
After:
=====
text data bss dec hex filename
27893 9792 256 37941 9435 drivers/mfd/tps65219.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/117946696551de41b706ea9b973a7ccaacea5178.1750530460.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
Several structures are not modified in this driver. Constifying them moves
some data to a read-only section, so increases overall security, especially
when the structure holds some function pointers. This is the case for
'gpio_keys_platform_data' and 'mfd_cell'.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
18321 13952 192 32465 7ed1 drivers/mfd/rohm-bd71828.o
After:
=====
text data bss dec hex filename
22897 9376 192 32465 7ed1 drivers/mfd/rohm-bd71828.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/037e28e587ae899da9acdb45c606d75ec61f858b.1750501700.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
commit b0a5cde57c ("dt-bindings: mfd: Explain lack of child dependency
in simple-mfd") pointed out that it's a mistake for a child device of
a simple MFD device to depend on the simple MFD device's clock resources.
fsl,imx8qxp-csr.yaml happens to make that mistake. To fix that, remove
fsl,imx8qxp-csr.yaml and use "simple-pm-bus" and "syscon" as the CSR node's
compatible strings in the examples of fsl,imx8qxp-pixel-link-msi-bus.yaml
to replace the wrong compatible strings which include "simple-mfd" and
"fsl,imx8qxp-mipi-lvds-csr". Since fsl,imx8qxp-pixel-link-msi-bus.yaml
as the last user of the CSR compatible strings no longer uses them, it's
safe to remove the fsl,imx8qxp-csr.yaml binding documentation.
Fixes: 9b2c55b540 ("dt-bindings: mfd: Add i.MX8qm/qxp Control and Status Registers module binding")
Fixes: c08645ea21 ("dt-bindings: bus: Add Freescale i.MX8qxp pixel link MSI bus binding")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250620022537.3072877-1-victor.liu@nxp.com
Signed-off-by: Lee Jones <lee@kernel.org>
On newer boards featuring the A523 SoC, the AXP323 (related to the
AXP313) is paired with the AXP717 and serves as a secondary PMIC
providing additional regulator outputs. However the MFD cells are all
registered with PLATFORM_DEVID_NONE, which causes the regulator cells
to conflict with each other.
Commit e37ec32188 ("mfd: axp20x: Allow multiple regulators") attempted
to fix this by switching to PLATFORM_DEVID_AUTO so that the device names
would all be different, however that broke IIO channel mapping, which is
also tied to the device names. As a result the change was later reverted.
Instead, here we attempt to make sure the AXP313/AXP323 regulator cell
does not conflict by explicitly giving it an ID number. This was
previously done for the AXP809+AXP806 pair used with the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250619173207.3367126-1-wens@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Combine the following separate plain text based bindings to YAML:
lpc1850-creg-clk.txt
pc1850-dmamux.txt
phy-lpc18xx-usb-otg.txt
Additional changes:
- remove label in example.
- remove dmamux consumer in example.
- remove clock consumer in example.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250602143612.943516-1-Frank.Li@nxp.com
Signed-off-by: Lee Jones <lee@kernel.org>
The charge-control subsystem in the ChromeOS EC is not strictly tied to
its USB-PD subsystem.
Since commit 7613bc0d11 ("mfd: cros_ec: Don't load charger with UCSI")
the presence of EC_FEATURE_UCSI_PPM would inhibit the probing of the
charge-control driver.
Furthermore recent versions of the EC firmware in Framework laptops
hard-disable EC_FEATURE_USB_PD to avoid probing cros-usbpd-charger,
which then also breaks cros-charge-control.
Instead use the dedicated EC_FEATURE_CHARGER.
Cc: stable@vger.kernel.org
Link: 1d7bcf1d50
Fixes: 555b5fcdb8 ("mfd: cros_ec: Register charge control subdevice")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Tested-by: Tom Vincent <linux@tlvince.com>
Link: https://lore.kernel.org/r/20250521-cros-ec-mfd-chctl-probe-v1-1-6ebfe3a6efa7@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
This driver implements the GPIO service on top of the SMC framework
on Apple Mac machines. In particular, these are the GPIOs present in the
PMU IC which are used to control power to certain on-board devices.
Although the underlying hardware supports various pin config settings
(input/output, open drain, etc.), this driver does not implement that
functionality and leaves it up to the firmware to configure things
properly. We also don't yet support interrupts/events. This is
sufficient for device power control, which is the only thing we need to
support at this point. More features will be implemented when needed.
To our knowledge, only Apple Silicon Macs implement this SMC feature.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sven Peter <sven@kernel.org>
Signed-off-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250610-smc-6-15-v7-6-556cafd771d3@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The System Management Controller (SMC) on Apple Silicon machines is a
piece of hardware that exposes various functionalities such as
temperature sensors, voltage/power meters, shutdown/reboot handling,
GPIOs and more.
Communication happens via a shared mailbox using the RTKit protocol
which is also used for other co-processors. The SMC protocol then allows
reading and writing many different keys which implement the various
features. The MFD core device handles this protocol and exposes it
to the sub-devices.
Some of the sub-devices are potentially also useful on pre-M1 Apple
machines and support for SMCs on these machines can be added at a later
time.
Co-developed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://lore.kernel.org/r/20250610-smc-6-15-v7-5-556cafd771d3@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The adp5589 support is based on legacy platform data and there's no
upstream platform using this device.
Moreover, recently, with
commit
480a8ad683 ("mfd: adp5585: Add Analog Devices ADP5585 core support")
we overlapped support for the adp5585 device (gpiochip part of it) but
since it actually makes sense for the device to be supported under MFD, we
can complement it and add the keymap support for it (properly based on FW
properties). And that is what
commit
04840c5363a6 ("Input: adp5585: Add Analog Devices ADP5585/89 support")
is doing.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-17-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for adding GPIs to the event FIFO. This is done by adding
irq_chip support. Like this, one can use the input gpio_keys driver as a
"frontend" device and input handler.
As part of this change, we now implement .request() and .free() as we can't
blindly consume all available pins as GPIOs (example: some pins can be
used for forming a keymap matrix).
Also note that the number of pins can now be obtained from the parent,
top level device. Hence the 'max_gpio' variable can be removed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-15-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP558x family supports a built in keypad matrix decoder which can
be added as an Input device. In order to both support the Input and the
GPIO device, we need to create a bitmap of the supported pins and track
their usage since they can either be used as GPIOs (GPIs) or as part of
the keymap.
We also need to mark special pins busy in case some features are being
used (ex: pwm or reset events).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-14-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP558x family of devices can be programmed to respond to some
especial events, In case of the unlock events, one can lock the keypad
and use KEYS or GPIs events to unlock it. For the reset events, one can
again use a combinations of GPIs/KEYs in order to generate an event that
will trigger the device to generate an output reset pulse.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-13-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add properties related to input events. These devices can act as
keyboards and can support events either via a keymap Matrix or through
GPIs. Note that the device needs to be an interrupt controller for GPIs
based events.
We specifically need a property specifying the pins used by the keymap
matrix since these devices have no requirement for rows and columns to be
contiguous without holes which is enforced by the standard input
properties.
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-11-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
