as6200 is a temperature sensor with 0.0625°C resolution and a
range between -40°C to 125°C.
By default, the driver configures as6200 as following:
- Converstion rate: 8 Hz
- Conversion mode: continuous
- Consecutive fault counts: 4 samples
- Alert state: high polarity
- Alert mode: comparator mode
Interrupt is supported for the alert pin.
Signed-off-by: Abdel Alkuor <alkuor@gmail.com>
Link: https://lore.kernel.org/r/d1686678991bf8ee0d00cb08ca046798f37ca4b3.1703127334.git.alkuor@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Gigabyte AORUS Waterforce
all-in-one CPU liquid coolers, which communicate through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] and
confirmed by me on a Waterforce X240 by observing the sent reports from
the official software.
Available sensors are pump and fan speed in RPM, as well as coolant
temperature. Also available through debugfs is the firmware version.
Attaching a fan is optional and allows it to be controlled from the
device. If it's not connected, the fan-related sensors will report
zeroes.
The addressable RGB LEDs and LCD screen are not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/issues/167
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231207122402.107032-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added custom channel-specific (temp1) attribute for resolution. The wait
time for a conversion in one-shot mode (enable = 0) depends on the
resolution.
When resolution is 12-bit, the conversion time is 140ms, but the minimum
update_interval is 125ms. Handled this problem by waiting an additional
15ms (125ms + 15ms = 140ms).
Added 'mask' parameter to the shutdown_write() function. Now it can
either write or update bits, depending on the value of mask. This is
needed, because for alarms a write is necessary, but for resolution only
the resolution bits should be updated.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20231031182158.124608-5-daniel.matyas@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
Monitor.
The LTC2991 is used to monitor system temperatures, voltages and
currents. Through the I2C serial interface, the eight monitors can
individually measure supply voltages and can be paired for
differential measurements of current sense resistors or temperature
sensing transistors. Additional measurements include internal
temperature and internal VCC.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231026103413.27800-2-antoniu.miclaus@analog.com
[groeck: Fixed up documentation warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
POWER-Z is a series of devices to monitor power characteristics of
USB-C connections and display those on a on-device display.
Some of the devices, notably KM002C and KM003C, contain an additional
port which exposes the measurements via USB.
This is a driver for this monitor port.
It was developed and tested with the KM003C.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230902-powerz-v4-1-7ec2c1440687@weissschuh.net
[groeck:
Release urb after hwmon registration error;
Move priv->status initialization to correct place before reinit_completion
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull documentation updates from Jonathan Corbet:
"Documentation work keeps chugging along; this includes:
- Work from Carlos Bilbao to integrate rustdoc output into the
generated HTML documentation. This took some work to figure out how
to do it without slowing the docs build and without creating people
who don't have Rust installed, but Carlos got there
- Move the loongarch and mips architecture documentation under
Documentation/arch/
- Some more maintainer documentation from Jakub
... plus the usual assortment of updates, translations, and fixes"
* tag 'docs-6.6' of git://git.lwn.net/linux: (56 commits)
Docu: genericirq.rst: fix irq-example
input: docs: pxrc: remove reference to phoenix-sim
Documentation: serial-console: Fix literal block marker
docs/mm: remove references to hmm_mirror ops and clean typos
docs/zh_CN: correct regi_chg(),regi_add() to region_chg(),region_add()
Documentation: Fix typos
Documentation/ABI: Fix typos
scripts: kernel-doc: fix macro handling in enums
scripts: kernel-doc: parse DEFINE_DMA_UNMAP_[ADDR|LEN]
Documentation: riscv: Update boot image header since EFI stub is supported
Documentation: riscv: Add early boot document
Documentation: arm: Add bootargs to the table of added DT parameters
docs: kernel-parameters: Refer to the correct bitmap function
doc: update params of memhp_default_state=
docs: Add book to process/kernel-docs.rst
docs: sparse: fix invalid link addresses
docs: vfs: clean up after the iterate() removal
docs: Add a section on surveys to the researcher guidelines
docs: move mips under arch
docs: move loongarch under arch
...
Add base support for Renesas HS3001 temperature
and humidity sensors and its compatibles HS3002,
HS3003 and HS3004.
The sensor has a fix I2C address 0x44. The resolution
is fixed to 14bit (ref. Missing feature).
Missing feature:
- Accessing non-volatile memory: Custom board has no
possibility to control voltage supply of sensor. Thus,
we cannot send the necessary control commands within
the first 10ms after power-on.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230725042207.22310-2-andre.werner@systec-electronic.com
[groeck: Cosmetic documentation fixup; added documentation to index;
replaced probe_new with probe dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMM665 and related chips are power controller/sequencer chips from
Summit Microelectronics. The company was acquired by Qualcomm in 2012,
and support for the chip series stopped.
The chips are long since gone from active use, making the driver
unsupportable and just consuming space and compile time. Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The series 2022/2023 reports slightly longer vendor/product strings
and shares USB ids. Technically the reply size is the USB HID packet
size (64 bytes) but all the supported commands do not use more than 8
bytes and replies reporting back strings do not use more then 24 bytes
(vendor and product are in one string in the newer devices now). The
rest of the reply is always filled with '\0'. Also update comments
and documentation accordingly.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZJbB72CAPmLflhHG@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
OneXPlayer boards from the last generation (both for OneXPlayer and AOK
ZOE brands) have a toggle in the EC to switch the "Turbo/Silent" button
into a different keyboard event.
Add a means to use that "Turbo button takeover" function and expose it
to userspace in a custom sysfs `tt_toggle` attribute. It can be read to
take the current state. Write 1|0 to activate the function. The specific
keycode is dependent on the board but can be checked by running
`evtest` utility.
Newer BIOS on the OneXPlayer added this function aside from string changes.
Add a board enum to differentiate it from the old OneXplayer Mini AMD BIOS.
Currently known supported boards:
- AOK ZOE A1
- OneXPlayer Mini AMD (only newer BIOS version supported)
- OneXPlayer Mini Pro
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230611143332.40590-2-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Leakshield leak prevention system, which communicates
through a proprietary USB HID protocol. Implemented by Noah Bergbauer [1].
Two temperature sensors are exposed, along with pressure (current, min, max
and target), reservoir volume (total and filled), pump speed and flow. Pump
speed and flow values are user provided and allow the Leakshield to
optimize its operation. Writing them to the device is subject of future
patches.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/41
Originally-from: Noah Bergbauer <main@ehvag.de>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230520095447.509287-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove description of deprecated registration functions from the hardware
monitoring kernel API documentation to help ensure that no attempts are
made to use them in new drivers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the option to control fan PWM on Aquacomputer Aquaero. The Aquaero is
the most complex Aquacomputer device, control is therefore more complicated
then on already supported devices.
Setting PWM requires multiple steps. First, an internal static PWM
controller is set to the desired PWM value. Second, the fan is set to use
that PWM controller. Last, the minimum and maximum accepted PWM values
of the fan are set to allow all possible PWM values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-7-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Fujitsu OEM Mainboard business was acquired by Kontron,
so the specifications of the Teutates chip was transferred to
the new Kontron FTP server.
Update the specifications website accordingly. The outdated
sensors how-to was omitted.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230226014830.10929-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
