Add a debugfs subdirectory i915_params with all the i915 module
parameters. This is a first step, with lots of boilerplate, and not much
benefit yet.
This will result in a new device specific debugfs directory at
/sys/kernel/debug/dri/<N>/i915_params duplicating the module specific
sysfs directory at /sys/module/i915/parameters/. Going forward, all
users of the parameters should use the debugfs, with the module
parameters being phased out.
Add debugfs permissions to I915_PARAMS_FOR_EACH(). This duplicates the
mode with module parameter sysfs, but the goal is to make the module
parameters read-only initial values for device specific parameters.
0 mode will bypass debugfs creation. Use it for verbose_state_checks
which will need special attention in follow-up work.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/600101c8433e7caf9303663fc85a9972fa1f05e7.1575560168.git.jani.nikula@intel.com
intel_prepare_plane_fb() will always pin plane_state->hw.fb whenever
it is present. We copy that from the master plane to the slave plane,
but we fail to copy the corresponding ggtt view. Thus when it comes time
to pin the slave plane's fb we use some stale ggtt view left over from
the last time the plane was used as a non-slave plane. If that previous
use involved 90/270 degree rotation or remapping we'll try to shuffle
the pages of the new fb around accordingingly. However the new
fb may be backed by a bo with less pages than what the ggtt view
rotation/remapped info requires, and so we we trip a GEM_BUG().
Steps to reproduce on icl:
1. plane 1: whatever
plane 6: largish !NV12 fb + 90 degree rotation
2. plane 1: smallish NV12 fb
plane 6: make invisible so it gets slaved to plane 1
3. GEM_BUG()
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/951
Fixes: 1f594b209f ("drm/i915: Remove special case slave handling during hw programming, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
If 'CONFIG_DRM_I915_CAPTURE_ERROR' not configured, there is an error
when compile the kernel:
drivers/gpu/drm/i915/gt/intel_reset.c:
In function intel_gt_handle_error:
drivers/gpu/drm/i915/gt/intel_reset.c:1233:3:
error: too few arguments to function i915_capture_error_state
i915_capture_error_state(gt->i915);
^~~~~~~~~~~~~~~~~~~~~~~~
In file included
from ./drivers/gpu/drm/i915/i915_drv.h:97:0,
from ./drivers/gpu/drm/i915/display/intel_display_types.h:46,
from drivers/gpu/drm/i915/gt/intel_reset.c:10:
./drivers/gpu/drm/i915/i915_gpu_error.h:267:20: note: declared here
static inline void i915_capture_error_state(struct drm_i915_private *dev_priv,
Fixes: 742379c0c4 ("drm/i915: Start chopping up the GPU error capture")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113081942.15982-1-zhangxiaoxu5@huawei.com
If 'CONFIG_DRM_I915_CAPTURE_ERROR' not configured, there are some
errors like:
drivers/gpu/drm/i915/i915_irq.o:
In function `i915_vma_capture_finish':
./drivers/gpu/drm/i915/i915_gpu_error.h:312:
multiple definition of `i915_vma_capture_finish'
drivers/gpu/drm/i915/i915_drv.o:
./drivers/gpu/drm/i915/i915_gpu_error.h:312: first defined here
So, add 'static inline' on the defineation of the 'i915_vma_capture_finish'
Fixes: d713e3ab93fdc("drm/i915: Correct typo in i915_vma_compress_finish stub")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113104009.13274-1-zhangxiaoxu5@huawei.com
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
There seems to be some undocumented bandwidth
bottleneck/dependency which scales with CDCLK,
causing FIFO underruns when CDCLK is too low,
even when it's correct from BSpec point of view.
Currently for TGL platforms we calculate
min_cdclk initially based on pixel_rate divided
by 2, accounting for also plane requirements,
however in some cases the lowest possible CDCLK
doesn't work and causing the underruns.
We've found experimentally that raising cdclk to
at least pixel_rate (rather than pixel_rate/2)
eliminates these underruns, so let's use this as a
temporary workaround until the hardware team
can suggest a more precise remedy.
Explicitly stating here that this seems to be currently
rather a Hack, than final solution.
v2: Use clamp operation instead of min(Matt Roper)
v3: - Fixed commit message(Matt Roper)
- Now using pixel_rate instead of max_cdclk(Jani Nikula)
- Switched to max from clamp(Ville Syrjälä)
Hopefully this hybrid satisfies everyone :)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200109220547.23817-1-stanislav.lisovskiy@intel.com
Currently we first to try to unbind the VMA (and lazily rebind on next
use) as an optimisation during restore_ggtt_mappings. Ideally, the only
objects in the GGTT upon resume are the pinned kernel objects which
can't be unbound and need to be restored. As the unbind interferes with
the plan to mark those objects as active for error capture, forgo the
optimisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110110402.1231745-1-chris@chris-wilson.co.uk
When moving the pipe disable & co. function calls from
haswell_crtc_disable() into the encoder .post_disable() hooks I
neglected to account for the MST vs. DDI interactions properly.
This now leads us to call these functions two times for the last
MST stream (once from the MST code and a second time from the DDI
code). The calls from the DDI code should only be done for SST
and not MST. Add the proper check for that.
This results in an MCE on ICL. My vague theory is that we turn off
the transcoder clock from the MST code and then we proceed to touch
something in the DDI code which still depends on that clock causing
the hardware to become upset. Though I can't really explain why
Stan's hack of omitting the pipe disable in the MST code would avoid
the MCE since we should still be turning off the transcoder clock.
But maybe there's something magic in the hw that keeps the clock on
as long as the pipe is on. Or maybe the clock isn't the problem and
we now touch something in the DDI disable code that really does need
the pipe to be still enabled.
v2: Rebase to latest drm-tip
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reported-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/901
Fixes: 773b4b5435 ("drm/i915: Move stuff from haswell_crtc_disable() into encoder .post_disable()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108144550.29280-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Fixes coccicheck warning:
drivers/gpu/drm/i915/i915_debugfs.c:3078:4-36: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/i915_debugfs.c:3078:4-36: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/i915_debugfs.c:3080:4-36: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/i915_debugfs.c:3080:4-36: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1578013959-31486-2-git-send-email-mafeng.ma@huawei.com
