Currently ath12k only supports string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for AHB bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCI bus chip in board-2.bin.
For WCN7850, it is not enough to distinguish all different chips.
Add a new string type which includes bus, chip id, board id, vendor,
device, subsystem-vendor and subsystem-device for WCN7850.
ath12k will first load board-2.bin and searches in it for the board data
with the above parameters. If matched with one board data, ath12k downloads
it to firmware. And if not, downloads board.bin instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-2-quic_bqiang@quicinc.com
Currently ath10k defines the following struct:
struct wmi_start_scan_tlvs {
u8 tlvs[0];
} __packed;
Per the guidance in [1] this should be a flexible array. However, a
direct replace to u8 tlvs[] results in the compilation error:
flexible array member in a struct with no named members
This is because C99 6.7.2.1 (16) requires that a structure containing
a flexible array member must have more than one named member.
So rather than defining a separate struct wmi_start_scan_tlvs which
contains the flexible tlvs[] array, just define the tlvs[] array where
struct wmi_start_scan_tlvs is being used.
No functional changes, compile tested only.
[1] https://docs.kernel.org/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231213-wmi_host_mem_chunks_flexarray-v1-2-92922d92fa2c@quicinc.com
In 'ath_ant_try_scan()', (most likely) the 2nd LNA's signal
strength should be used in comparison against RSSI when
selecting first LNA as the main one. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231211172502.25202-1-dmantipov@yandex.ru
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231117093056.873834-11-u.kleine-koenig@pengutronix.de
Since 'ath11k_wmi_tlv_parse_alloc()' always operates on
'skb->data, skb->len' tuple, it may be simplified to pass
the only 'skb' argument instead (which also implies
refactoring of 'ath11k_pull_bcn_tx_status_ev()' and
'ath11k_pull_chan_info_ev()' in the same way). Compile
tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161117.75145-1-dmantipov@yandex.ru
ath.git patches for v6.8.
We have new features only for ath12k but lots of small cleanup for
ath10k, ath11k and ath12k. And of course smaller fixes to several
drivers.
Major changes:
ath12k
* support one MSI vector
* WCN7850: support AP mode
Transform zero-length arrays `rate`, `adm_stat` and `msdu_cnt` into
proper flexible-array members in anonymous union in `struct
mt7996_mcu_all_sta_info_event` via the DECLARE_FLEX_ARRAY()
helper; and fix multiple -Warray-bounds warnings:
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:544:61: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:551:58: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:553:58: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:530:61: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:538:66: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:540:66: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:520:57: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
This results in no differences in binary output, helps with the ongoing
efforts to globally enable -Warray-bounds.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/ZXiU9ayVCslt3qiI@work
In v6.7-rc1 sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
Workaround the warnings by refactoring the code to a new function, which also
reduces code duplication. And in the new function use max3() to make the code
more readable.
No functional changes, compile tested only.
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161740.1582340-1-kvalo@kernel.org
This reverts commit 1f1f7d548a. The commit
caused bootup failure on QCN9274 hw2.0 platform. Incorrect hardcode DP
irq offset overwrite the CE irq, which caused the driver to miss the
mandatory bootup message from the firmware through the CE interrupt. This
occurs because the CE count differs between platforms. The revert has no
impact since the original change was based on an incorrect assumption.
Log:
ath12k_pci 0000:06:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
ath12k_pci 0000:06:00.0: failed to receive control response completion, polling..
ath12k_pci 0000:06:00.0: Service connect timeout
ath12k_pci 0000:06:00.0: failed to connect to HTT: -110
ath12k_pci 0000:06:00.0: failed to start core: -110
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214053215.2087308-1-quic_periyasa@quicinc.com
In 'rt2x00queue_create_tx_descriptor()', there is no need to call
'ieee80211_get_rts_cts_rate()' while checking for RTS/CTS frame
since this function returns NULL or pointer to internal bitrate
table entry, and the return value is not actually used. Compile
tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213051449.126963-1-dmantipov@yandex.ru
The XTAL SI is a serial interface to indirectly access registers of
analog hardware circuit. Since WiFi 7 chips use different registers, add
a ops to access them via common functions. This patch doesn't change logic
for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-2-pkshih@realtek.com
With formatted string loaded from firmware file, we can use the formatted
string ID and get corresponding string, and then use regular rtw89_debug()
to show the message if debug mask of RFK is enabled.
If the string ID doesn't present, fallback to print plain hexadecimal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-7-pkshih@realtek.com
RFK log events contains two types. One called RUN log is to reflect state
during RFK is running, and it replies on formatted string loaded from
firmware file, but print this type as plain hexadecimal only in this patch.
The other is REPORT log that reflects the final result of a RFK, and
each calibration has its own struct to carry many specific information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-6-pkshih@realtek.com
Trigger a RFK (RF calibration) in firmware by a H2C command, and in
progress it reports log and a result finally by C2H events. Firstly, add
prototype of the C2H event handlers to have a simple picture of framework.
The callers who trigger H2C will wait until a C2H event is received,
so we must process these C2H events in receiving process. Thus, mark this
kind of C2H events as atomic. Also, timestamp is also useful for
debugging, mark C2H events carrying RFK log as atomic as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-5-pkshih@realtek.com
To debug RFK (RF calibration) in firmware, it sends log via firmware C2H
events to driver with string format ID and four arguments. Load formatted
string from firmware file, and the string ID can get back its string. Then,
use regular print format to show the message.
This firmware element layout looks like
+============================================+
| elm ID | elm size | version | |
+----------+----------+----------+-----------+
| | nr |rsvd |rfk_id|rsvd|
+--------------------------------------------+
| offset[] (__le16 * nr) |
| ... |
+--------------------------------------------+
| formatted string with null termintor (*nr) |
| ... |
+============================================+
* a firmware file can contains more than one elements with this element ID
named RTW89_FW_ELEMENT_ID_RFKLOG_FMT (19), because many RFK needs its
own formatted strings, so add 'rfk_id' to know it belongs to which RFK.
* the 'formatted string' just follow 'offset[]' without padding to align
32bits.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-4-pkshih@realtek.com
8922AE has more than one hardware version, and they use different BB MCU
firmware, so occupy a byte from element priv[] to annotate version. Since
there are more than one firmware and only matched version is adopted,
return 1 to ignore not matched firmware.
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | element_priv[] |
+-------------------------------------------+
change to |
v
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | cv | element_rsvd[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-3-pkshih@realtek.com
The TX power track tables are used to define compensation power reflected
to thermal value. Currently, we have 16 (2 * 4 * 2) tables made by
combinations of
{negative/positive thermal value, 2GHz/2GHz-CCK/5GHz/6GHz, path A/B}
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-2-pkshih@realtek.com
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80 ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
The build can become unreproducible if the list of files
found by $(wildcard ...) differs. Sort the list to avoid
this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the `ath_set_channel()` function, we only reset surveys that are not
from the current channel. This leads to the accumulation of survey data for
the current channel indefinitely. This may not be the most optimal
approach, as we want the ACS to rely on the most recent survey.
So reset the survey data for the current channel at the start of each scan.
Signed-off-by: Hancheng Yang <hyang@freebox.fr>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231205170623.3029689-1-hyang@freebox.fr
We observe some packets are discarded in ieee80211_rx_handlers_result
function for WCN7850. This is because the way to get multicast/broadcast
indicator with RX_MSDU_END_INFO5_DA_IS_MCBC & info5 is incorrect. It should
use RX_MSDU_END_INFO13_MCAST_BCAST & info13 to get multicast/broadcast
indicator.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231206141759.5430-1-quic_lingbok@quicinc.com
When the MAC address read from the efuse data is invalid, warn the
user and use a random MAC address instead.
On a device I am currently using (Anbernic RG-ARC) with a rtw8821cs
the efuse appears to be incompletely/improperly programmed. The MAC
address reads as ff:ff:ff:ff:ff:ff. When networkmanager attempts to
initiate a connection (and I haven't hard-coded a MAC address or
set it to random) it fails to establish a connection.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231208150739.129753-1-macroalpha82@gmail.com
After -Wstringop-overflow got enabled, the rtw89 driver produced
two odd warnings with gcc-13:
drivers/net/wireless/realtek/rtw89/coex.c: In function 'rtw89_btc_ntfy_scan_start':
drivers/net/wireless/realtek/rtw89/coex.c:5362:50: error: writing 1 byte into a region of size 0 [-Werror=stringop-overflow=]
5362 | wl->dbcc_info.scan_band[phy_idx] = band;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
In file included from drivers/net/wireless/realtek/rtw89/coex.h:8,
from drivers/net/wireless/realtek/rtw89/coex.c:5:
drivers/net/wireless/realtek/rtw89/core.h:1441:12: note: at offset [64, 255] into destination object 'scan_band' of size 2
1441 | u8 scan_band[RTW89_PHY_MAX]; /* scan band in each phy */
| ^~~~~~~~~
drivers/net/wireless/realtek/rtw89/coex.c: In function 'rtw89_btc_ntfy_switch_band':
drivers/net/wireless/realtek/rtw89/coex.c:5406:50: error: writing 1 byte into a region of size 0 [-Werror=stringop-overflow=]
5406 | wl->dbcc_info.scan_band[phy_idx] = band;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/net/wireless/realtek/rtw89/core.h:1441:12: note: at offset [64, 255] into destination object 'scan_band' of size 2
1441 | u8 scan_band[RTW89_PHY_MAX]; /* scan band in each phy */
| ^~~~~~~~~
I don't know what happened here, but adding an explicit range check
shuts up the output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204073020.1105416-1-arnd@kernel.org
