Hardware or bootloader will initialize TLB entries to any value, which
may collide with kernel's UNIQUE_ENTRYHI value. On MIPS microAptiv/M5150
family of cores this will trigger machine check exception and cause boot
failure. On M5150 simulation this could happen 7 times out of 1000 boots.
Replace local_flush_tlb_all() with r4k_tlb_uniquify() which probes each
TLB ENTRIHI unique value for collisions before it's written, and in case
of collision try a different ASID.
Cc: stable@kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
It can be known that the function “kfree” performs a null pointer check
for its input parameter.
It is therefore not needed to repeat such a check before its call.
Thus remove a redundant pointer check.
The source code was transformed by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
mc146818_get_cmos_time() is now mostly equivalent to mc146818_get_time()
from drivers/rtc/rtc-mc146818-lib.c, with the latter using a more
advanced algorithm (which checks the UIP bit in the CMOS). The Malta
and Loongson2ef platforms, the only users of mc146818_get_cmos_time()
have RTC devices that should be MC146818 compatible.
So, rewrite mc146818_get_cmos_time() in a way that uses
mc146818_get_time() and add CONFIG_RTC_MC146818_LIB as a dependency of
CONFIG_MIPS_MALTA and CONFIG_CPU_LOONGSON2EF.
The should be safe as:
- malta_defconfig already uses a standard RTC CMOS driver
(CONFIG_RTC_DRV_CMOS=y). The Malta board has an Intel 82371EB (PIIX4E)
south bridge with the CMOS RTC, so should work correctly with the
modification,
- Loongson2e and 2f apparently use the VIA686B south bridge and the AMD
CS5536 south bridge respectively (at least according to Kconfig). I
have checked datasheets of both and these appear to be MC146818
software compatible.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The mc146818_decode_year macro is used only in mc146818_get_cmos_time(),
which in turn is called only in
arch/mips/loongson2ef/common/time.c
and
arch/mips/mti-malta/malta-time.c
so on mach-jazz it is unused and can be removed. On other platforms it
is defined in the same way, so it can be safely folded into
mc146818_get_cmos_time().
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The mc146818_decode_year macro is used only in mc146818_get_cmos_time,
which in turn is called only in
arch/mips/loongson2ef/common/time.c
and
arch/mips/mti-malta/malta-time.c
So no SNI or mach-rm content. SNI did not use mc146818_get_cmos_time
apparently since
commit 06cf5583fd ("[MIPS] SNI RM updates")
in 2007.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
I have checked carefully: this function is unused, so remove it.
The last caller appears to have been removed in 2007 in
commit 4b550488f8 ("[MIPS] Deforest the function pointer jungle in the time code.")
mc146818-time.h is included only in three files:
- arch/mips/mti-malta/malta-time.c
- arch/mips/loongson64/numa.c
- arch/mips/loongson2ef/common/time.c
Also, remove unused macros USEC_AFTER/USEC_BEFORE.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
On MIPS architecture with CPS-based SMP support, all CPU cores in the
same cluster run at the same frequency since they share the same L2
cache, requiring a fixed CPU/L2 cache ratio.
This allows to implement calibrate_delay_is_known(), which will return
0 (triggering calibration) only for the primary CPU of each
cluster. For other CPUs, we can simply reuse the value from their
cluster's primary CPU core.
With the introduction of this patch, a configuration running 32 cores
spread across two clusters sees a significant reduction in boot time
by approximately 600 milliseconds.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The initial implementation of this function goes through all the CPUs
in a cluster to determine if the current CPU is the only one
running. This process occurs every time the function is called.
However, during boot, we already perform this task, so let's take
advantage of this opportunity to create and fill a CPU bitmask that
can be easily and efficiently used later.
This patch modifies the function to allow providing the first
available online CPU when one already exists, which is necessary for
delay CPU calibration optimization.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
It is possible that MMID is supported at the CPU level, but its
integration in a SoC prevents its usage. For instance, if the
System-level Interconnect (also known as Network on Chip) does not
support global invalidation, then the MMID feature is not usable. The
current implementation of MMID relies on the GINV* instructions.
This patch allows the disabling of MMID based on a device tree
property, as this issue cannot be detected at runtime.
MMID is set up very early during the boot process, even before device
tree data can be accessed. Therefore, when we determine whether MMID
needs to be disabled, some MMID setup has already been performed for
the boot CPU. Consequently, we must revert the MMID setup on the first
CPU before disabling the feature for the subsequent CPUs that will be
initialized later.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Enable I2C support on the EyeQ5 platform. The evaluation board has a
temperature sensor mounted which helps test the integration.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This platform uses the same GPIO controller as Nomadik. It however has
its own pinconf & pinmux controller. EyeQ5 is the first platform to use
gpio-nomadik independently from pinctrl-nomadik.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the SoC I2C controller nodes to the platform devicetree. Use a
default bus frequency of 400kHz. They are AMBA devices that are matched
on PeriphID.
Set transfer timeout to 10ms instead of Linux's default of 200ms.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These functions are exported but their prototypes are not defined.
This patch adds the missing function prototypes to fix the following
compilation warnings:
arch/mips/kernel/vpe-mt.c:180:7: error: no previous prototype for 'vpe_alloc' [-Werror=missing-prototypes]
180 | void *vpe_alloc(void)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:198:5: error: no previous prototype for 'vpe_start' [-Werror=missing-prototypes]
198 | int vpe_start(void *vpe, unsigned long start)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:208:5: error: no previous prototype for 'vpe_stop' [-Werror=missing-prototypes]
208 | int vpe_stop(void *vpe)
| ^~~~~~~~
arch/mips/kernel/vpe-mt.c:229:5: error: no previous prototype for 'vpe_free' [-Werror=missing-prototypes]
229 | int vpe_free(void *vpe)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
vmlinux.bin.* files are built as prerequisites of other objects.
There is no need to use extra-y, which is planned for deprecation.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Not all tasks have an ABI associated or vDSO mapped,
for example kthreads never do.
If such a task ever ends up calling stack_top(), it will derefence the
NULL ABI pointer and crash.
This can for example happen when using kunit:
mips_stack_top+0x28/0xc0
arch_pick_mmap_layout+0x190/0x220
kunit_vm_mmap_init+0xf8/0x138
__kunit_add_resource+0x40/0xa8
kunit_vm_mmap+0x88/0xd8
usercopy_test_init+0xb8/0x240
kunit_try_run_case+0x5c/0x1a8
kunit_generic_run_threadfn_adapter+0x28/0x50
kthread+0x118/0x240
ret_from_kernel_thread+0x14/0x1c
Only dereference the ABI point if it is set.
The GIC page is also included as it is specific to the vDSO.
Also move the randomization adjustment into the same conditional.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Now that OF ahb support was added to the ath9k driver, we can use it to
enable and use the SoC wireless found in these chipsets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the MMC/SDHCI controller found in the eyeQ5 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the MMC/SDHCI controller found in the eyeQ6 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
request_mem_region() will return NULL instead of error code
when the memory request fails. Therefore, we should check if
the return value is non-zero instead of less than zero. In
this way, this patch also fixes the build warnings:
arch/mips/lantiq/falcon/sysctrl.c:214:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
214 | res_status.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:216:47: error: ordered comparison of pointer with integer zero [-Werror=extra]
216 | res_ebu.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:219:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
219 | res_sys[0].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:222:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
222 | res_sys[1].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:225:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
225 | res_sys[2].name) < 0))
|
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
"prom.h" includes the prototype of ltq_soc_init(). Fix warning:
arch/mips/lantiq/falcon/sysctrl.c:185:13: error: no previous prototype for 'ltq_soc_init' [-Werror=missing-prototypes]
185 | void __init ltq_soc_init(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is a defined but unused function. Fix warning:
arch/mips/lantiq/falcon/sysctrl.c:75:6: error: no previous prototype for 'falcon_trigger_hrst' [-Werror=missing-prototypes]
75 | void falcon_trigger_hrst(int level)
| ^~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
ltq_get_cp1_base() is an exported function, we must define
its prototype on header file. Fix warning:
arch/mips/lantiq/xway/vmmc.c:22:15: error: no previous prototype for 'ltq_get_cp1_base' [-Werror=missing-prototypes]
22 | unsigned int *ltq_get_cp1_base(void)
| ^~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following missing-prototypes warning:
arch/mips/lantiq/xway/gptu.c:197:12: error: no previous prototype for 'gptu_init' [-Werror=missing-prototypes]
197 | int __init gptu_init(void)
| ^~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following missing-prototypes warning:
arch/mips/lantiq/xway/clk.c:77:15: error: no previous prototype for 'ltq_ar9_sys_hz' [-Werror=missing-prototypes]
77 | unsigned long ltq_ar9_sys_hz(void)
| ^~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following build warnings:
arch/mips/lantiq/irq.c:340:12: error: no previous prototype for 'icu_of_init' [-Werror=missing-prototypes]
340 | int __init icu_of_init(struct device_node *node, struct device_node *parent)
| ^~~~~~~~~~~
arch/mips/lantiq/irq.c:418:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
418 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/irq.c:424:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
424 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following missing-prototypes build warning:
arch/mips/lantiq/xway/dcdc.c:49:12: error: no previous prototype for 'dcdc_init' [-Werror=missing-prototypes]
49 | int __init dcdc_init(void)
| ^~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following missing-prototypes build warning:
arch/mips/pci/pci-lantiq.c:239:12: error: no previous prototype for 'pcibios_init' [-Werror=missing-prototypes]
239 | int __init pcibios_init(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following missing-prototypes build warning:
arch/mips/lantiq/xway/dma.c:293:1: error: no previous prototype for 'dma_init' [-Werror=missing-prototypes]
293 | dma_init(void)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64 ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
arch/mips/loongson64/setup.c: warning: EXPORT_SYMBOL() is not used, but #include <linux/export.h> is present
So fix these build warnings for MIPS/Loongson.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This function is only used in the current source file. Mark it as
static to fix the compilation error:
arch/mips/pci/pci-rt2880.c:267:12: error: no previous prototype for 'pcibios_init' [-Werror=missing-prototypes]
267 | int __init pcibios_init(void)
| ^~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the missing header "asm/time.h" which defines the function
prototypes of get_c0_perfcount_int() and get_c0_compare_int().
This patch fixes the following build warnings:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When starting up, the GARDENA smart Gateway's power LED should be
flashing green. It is unclear why it was initially set to "off".
The LED frequency cannot be configured in the devicetree. Luckily, the
default is 1 Hz, which is what we want.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Most notably, add the mediatek,sysctl phandle and remove the redundant
reset/interrupt-related properties from the watchdog node. This is in
line with the corresponding devicetree (mt7628an.dtsi) used by the
OpenWrt project.
This has been tested on the MT7688-based GARDENA smart Gateway.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
As the MT7628 and MT7688 are identical in most respects, mt7628a.dtsi is
used for both SoCs. To prevent "Kernel panic - not syncing: unable to
get CPU clock, err=-2" and allow an MT7688-based board to boot, the
following must be allowed:
compatible = "ralink,mt7628-sysc", "ralink,mt7688-sysc", "syscon";
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pull i2c fixes from Wolfram Sang:
- subsystem: convert drivers to use recent callbacks of struct
i2c_algorithm A typical after-rc1 cleanup, which I couldn't send in
time for rc2
- tegra: fix YAML conversion of device tree bindings
- k1: re-add a check which got lost during upstreaming
* tag 'i2c-for-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: k1: check for transfer error
i2c: use inclusive callbacks in struct i2c_algorithm
dt-bindings: i2c: nvidia,tegra20-i2c: Specify the required properties
