Getting wedged device on driver init is pretty much unrecoverable.
Since we're running various scenarios that may potentially hit this in
CI (module reload / selftests / hotunplug), and if it happens, it means
that we can't trust any subsequent CI results, we should just apply the
taint to let the CI know that it should reboot (CI checks taint between
test runs).
v2: Comment that WEDGED_ON_INIT is non-recoverable, distinguish
WEDGED_ON_INIT from WEDGED_ON_FINI (Chris)
v3: Appease checkpatch, fixup search-replace logic expression mindbomb
in assert (Chris)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200706144107.204821-1-michal@hardline.pl
Normally i85x/i865 3D activity will block FBC until a 2D blit
occurs. I suppose this was meant to avoid recompression while
3D activity is still going on but the frame hasn't yet been
presented. Unfortunately that also means that a page flipped
3D workload will permanently block FBC even if it only renders
a single frame and then does nothing.
Since we are using software render tracking anyway we might as
well flip the chicken bit so that 3D does not block FBC. This
will avoid the permament FBC blockage in the aforemention use
case, but thanks to the software tracking the compressor will
not disturb 3D rendering activity.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Unlike all the other pre-snb desktop platforms i865 actually
supports FBC. Let's enable it.
Quote from the spec:
"DevSDG provides the same Run-Length Encoded Frame Buffer
Compression (RLEFBC) function as exists in DevMGM."
As i865 only has the one pipe we want to skip massaging the
plane<->pipe assignment aimed at getting FBC+LVDS working on
the mobile platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Consult the actual plane stride instead of the fb stride. The two
will disagree when we remap the gtt. The plane stride is what the
hw will be fed so that's what we should look at for the FBC
retrictions/cfb allocation.
Since we no longer require a fence we are going to attempt using
FBC with remapping, and so we should look at correct stride.
With 90/270 degree rotation the plane stride is stored in units
of pixels, so we need to conver it to bytes for the purposes
of calculating the cfb stride. Not entirely sure if this matches
the hw behaviour though. Need to reverse engineer that at some
point...
We also need to reorder the pixel format check vs. stride check
to avoid triggering a spurious WARN(stride & 63) with cpp==1 and
plane stride==32.
v2: Try to deal with rotated stride and related WARN
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 691f7ba58d ("drm/i915/display/fbc: Make fences a nice-to-have for GEN9+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Avoid waking up the device and taking stale locks if we know that the
object is not currently mmapped. This is particularly useful as not many
object are actually mmapped and so we can destroy them without waking
the device up, and gives us a little more freedom of workqueue ordering
during shutdown.
v2: Pull the release_mmap() into its single user in freeing the objects,
where there can not be any race with a concurrent user of the freed
object. Or so one hopes!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>,
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>,
Link: https://patchwork.freedesktop.org/patch/msgid/20200702163623.6402-2-chris@chris-wilson.co.uk
We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around
5 intel_dport
36 dport
479 intel_dig_port
352 dig_port
Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.
v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
If the driver gets stuck holding the kernel timeline, we cannot issue a
heartbeat and so fail to discover that the driver is indeed stuck and do
not issue a GPU reset (which would hopefully unstick the driver!).
Switch to using a trylock so that we can query if the heartbeat's
timeline mutex is locked elsewhere, and then use the timer to probe if it
remains stuck at the same spot for consecutive heartbeats, indicating
that the mutex has not been released and the engine has not progressed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702095219.963-1-chris@chris-wilson.co.uk
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before encoder_type is set. This caused GEN11+ to incorrectly strip
HBR3 from source rates for edp. Move intel_dp_set_source_rates() to
after encoder_type is set. Add comment to intel_dp_is_edp() describing
unsafe usages.
v2: Alter intel_dp_set_source_rates final position (Ville/Manasi).
Remove outdated comment (Ville).
Slight optimization of control flow in intel_dp_init_connector.
Slight rewording in commit message.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630233310.10191-1-matthew.s.atwood@intel.com
When the reference clock is 38.4MHz, using the current TBT PLL
fractional divider value results in a slightly off TBT link frequency.
This causes an endless loop of link training success followed by a bad
link signaling and retraining at least on a Dell WD19TB TBT dock. The
workaround provided by the HW team is to divide the fractional divider
value by two. This fixed the link training problem on the ThinkPad dock.
The same workaround is needed on some EHL platforms and for combo PHY
PLLs, these will be addressed in a follow-up.
Bspec: 49204
References: HSDES#22010772725
References: HSDES#14011861142
Reported-and-tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629185848.20550-1-imre.deak@intel.com
The obj->lut_list is traversed when the object is closed as the file
table is destroyed during process termination. As this occurs before we
kill any outstanding context if, due to some bug or another, the closure
is blocked, then we fail to shootdown any inflight operations
potentially leaving the GPU spinning forever. As we only need to guard
the list against concurrent closures and insertions, the hold is short
and merits being treated as a simple spinlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701084439.17025-1-chris@chris-wilson.co.uk
Rearrange the allocation of the mm_struct registration to avoid
allocating underneath the i915->mm_lock, so that we avoid tainting the
lock (and in turn many other locks that may be held as i915->mm_lock is
taken, and those locks we may want on the free [shrinker] paths). In
doing so, we convert the lookup to be RCU protected by courtesy of
converting the free-worker to be an rcu_work.
v2: Remember to use hash_rcu variants to protect the list iteration from
concurrent add/del.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619194038.5088-1-chris@chris-wilson.co.uk
The default fbc1 compression interval we use is 500 frames. That
translates to over 8 seconds typically. That's rather excessive
so let's drop it to 1 second.
The hardware will not attempt recompression unless at least one
line has been modified, so a shorter compression interval should
not cause extra bandwidth use in the purely idle scenario. Of
course in the mostly idle case we are possibly going to recompress
a bit more.
Should really try to find some kind of sweet spot to minimize
the energy usage...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The current fence_y_offset calculation is broken. I think it more or
less used to do the right thing, but then I changed the plane code
to put the final x/y source offsets back into the src rectangle so
now it's just subtraacting the same value from itself. The code would
never have worked if we allowed the framebuffer to have a non-zero
offset.
Let's do this in a better way by just calculating the fence_y_offset
from the final plane surface offset. Note that we don't align the
plane surface address to fence rows so with horizontal panning there's
often a horizontal offset from the fence start to the surface address
as well. We have no way to tell the hardware about that so we just
ignore it. Based on some quick tests the invlidation still happens
correctly. I presume due to the invalidation nuking at least the full
line (or a segment of multiple lines).
Fixes: 54d4d719fa ("drm/i915: Overcome display engine stride limits via GTT remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-4-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Currently there is no null check for a failed memory allocation
on the dsb object and without this a null pointer dereference
error can occur. Fix this by adding a null check.
Note: added a drm_err message in keeping with the error message style
in the function.
Addresses-Coverity: ("Dereference null return")
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616114221.73971-1-colin.king@canonical.com
The linetime watermark is a 9 bit value, which gives us
a maximum linetime of just below 64 usec. If the linetime
exceeds that value we currently just discard the high bits
and program the rest into the register, which angers the
state checker.
To avoid that let's just clamp the value to the max. I believe
it should be perfectly fine to program a smaller linetime wm
than strictly required, just means the hardware may fetch data
sooner than strictly needed. We are further reassured by the
fact that with DRRS the spec tells us to program the smaller
of the two linetimes corresponding to the two refresh rates.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625200003.12436-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The DP spec says:
"The transmitter shall support at least three levels of voltage
swing (Levels 0, 1, and 2).
If only three levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 10 (Level 2)),
this bit shall be set to 1, and cleared in all other cases.
If all four levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 11 (Level 3)),
this bit shall be set to 1,and cleared in all other cases."
Let's follow that exactly instead of the current apporach
where we can set those also for vswing/preemph levels 0 or 1
(or 2 when the platform max is 3).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Catch up with upstream, in particular to get c1e8d7c6a7 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
