From Simon Horman:
Renesas ARM-based SoC DT updates for v3.11
* Armadillo800eva reference DT - bring up armadillo800eva baord
using DT as much as possible
* Remove unused GIC dtsi entries for r8a7790 and r8a73a4
* Add AS3711 and CPUFreq DT bindings for kzm9g-reference
* Add irqpin DT support for marzen-reference
* tag 'renesas-dt-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen-reference: add irqpin support in DT
ARM: shmobile: kzm9g-reference: add AS3711 and CPUFreq DT bindings
ARM: shmobile: armadillo800eva: Reference DT implementation
ARM: shmobile: Remove unused r8a7790 GIC CPU interface DT bits
ARM: shmobile: Remove unused r8a73a4 GIC CPU interface DT bits
ARM: shmobile: r8a7740: Prepare for reference DT setup
ARM: shmobile: r8a7740: Add OF support to initialze the GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu dt changes for v3.11 (round 4)
- kirkwood
- reshuffle nodes from kirkwood.dtsi to -6281.dtsi, etc
- add i2c-gpio for km_kirkwood
- add cpu node so pending cpufreq driver will init
* tag 'dt-3.11-4' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood add cpus definition needed by cpufreq driver to dtsi
ARM: kirkwood: add i2c-gpio controller for km_kirkwood
ARM: kirkwood: refactor dtsi to largest common nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
From Tony Prisk, vt8500 devicetree updates for 3.11.
* tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm:
dts: vt8500: Correct reference clock on WM8850 SoCs
dts: vt8500: Add ARM, AHB, APB and DDR clock nodes to SoC files
dts: vt8500: Populate missing PLL nodes
dts: clk: vt8500: Update SoC dtsi to use WM8850 PLL clocks
dts: vt8500: Update serial nodes and disable by default in SoC files
dts: vt8500: Add devicetree support for WM8750 SoC and APC8750 board
dts: vt8500: Fix invalid/missing cpu nodes for soc files.
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds DT bindings for an AS3711 PMIC, used for supplying power to the
CPU, some peripherals and the backlight, as well as extends the cpu0 DT
node with OPPs and a reference to the PMIC to support the CPUFreq and
CPU DVFS functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the Armadillo800EVA to demonstrate how
DT may be used given the current state of driver device tree support.
This is intended to act as a reference for mach-shmobile developers.
This a rather bare bone version with the following devices supported:
- GIC
- irqpins
- i2c0/1
- touchscreen
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need three steps to prepare for the new Armadillo reference DT board code:
- Split the device list into r8a7740_early_devices used by the old platform
data setup (board-armadillo.c) and r8a7740_devices_dt used by both
setup variants.
- Introduce new r8a7740_init_delay() to be more flexible about calling
shmobile_setup_delay().
- For the generic r8a7740 support, we switch to device tree setup for
the GIC, the irqpin devices and the I2C controllers.
This is slightly similar to commit 3b00f93426
"ARM: shmobile: sh73a0: Do not use early devices with DT reference"
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add a variant to initalize the interrupt controller in case we describe
the GIC using the Device Tree and not platform data.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
WM8850 SoCs use a 24Mhz reference clock for the PLLs but the SoC file
currently parents all PLLs to the 25Mhz reference clock.
This patch corrects the PLL parent clock references.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
The Kirkwood CPU Freq driver needs a CPU definition in order for the probe
routine to activate it. Add a suitable definition to kirkwood.dtsi
This definition is only correct for single core SoCs. There is a dual core
SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in
the kernel don't currently support it. If they ever do the cpus definition
would need to be duplicated in each of the SoC specific include files.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The clocksource API has changed slightly, which causes a harmless
warning:
/git/arm-soc/drivers/clocksource/nomadik-mtu.c:259:28: warning: 'nmdk_timer_match' defined but not used [-Wunused-variable]
static struct of_device_id nmdk_timer_match[] __initconst = {
^
Fortunately, the same API change also lets us simplify the code
while removing the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
From jason Cooper, mvebu dt changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux: (27 commits)
arm: kirkwood: openblocks-a6: add support for Init button
arm: kirkwood: openblocks-a6: group pinmux configurations
arm: kirkwood: ts219: move pinmux configs to the right devices
arm: kirkwood: topkick: move pinmux configs to the right devices
arm: kirkwood: openblocks_a6: move pinmux configs to the right devices
arm: kirkwood: nsa310: move pinmux configs to the right devices
arm: kirkwood: readynas: move pinmux configs to the right devices
arm: kirkwood: mplcec4: move pinmux configs to the right devices
arm: kirkwood: buffalo linkstation: move pinmux configs to the right devices
arm: kirkwood: keymile: move pinmux configs to the right devices
arm: kirkwood: ns2: move pinmux configs to the right devices
arm: kirkwood: iomega ix2-200: move pinmux configs to the right devices
arm: kirkwood: iconnect: move pinmux configs to the right devices
arm: kirkwood: iconnect: give meaningful names to pinmux configs
arm: kirkwood: ib62x0: move pinmux configs to the right devices
arm: kirkwood: guruplug: move pinmux configs to the right devices
arm: kirkwood: goflexnet: move pinmux configs to the right devices
arm: kirkwood: dreamplug: move pinmux configs to the right devices
arm: kirkwood: dockstar: move pinmux configs to the right devices
arm: kirkwood: dlink dns: move pinmux configs to the right devices
...
This patch adds pinctrl configurations for at91 Timer Counter blocks.
These pin definitions can be referenced by "atmel,tcb-pwm" devices to
setup pins as PWM output for instance.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: switch to pinctrl pre-processor macros]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
the low power version have a mmc-spi
eanble mmc-spi and RV3029C2 RTC in at91_dt_defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
[nicolas.ferre@atmel.com: re-arranging nodes, removing nodes and some comments]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
UART0 is moved to generic at91sam9x5.dtsi file.
Both uarts are "disabled" as the corresponding pins on
Aria documentation are shown as GPIOs.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Due to a bug with RTC IMR, we cannot consider at91sam9x5 RTC compatible
with the previous one. Modify DT compatibility string, even if the driver
is not yet modified to take it into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
From Linus Walleij:
Device tree patches for the Nomadik machine:
- Move clock registration to the device tree
- Support probing the MTU timer from the device tree
- Register user LED and user key in the device tree
- Update defconfig to account for user LED and user key
- Move pin control mappings to the device tree
* tag 'nomadik-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: move the pin configuration to DT
ARM: nomadik: add led and key for S8815
ARM: nomadik: register clocksource from device tree
ARM: nomadik: convert all clocks except timer to dt
clocksource: nomadik-mtu: support of probe
Signed-off-by: Olof Johansson <olof@lixom.net>
This controller is used to access the reset management FPGA of the
km_kirkwood boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some kirkwood variants (for instance present in the prestera SoCs) do
not have all the peripherals whose nodes are declared in
kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC.
As discussed in [1], to avoid that these missing peripherals get
initialized which could result in system hangs when accessing
undocumented/not present HW registers, their corresponding OF nodes
should not get declared at all for some kirkwood variants.
The corresponding OF nodes of these peripherals thus are moved from
kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are
initialized for these variants where they are present.
[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.html
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of having one separate pinmux configuration for each LED, for
each GPIO of the GPIO header, for each DIP switch, this patch groups
them together in configurations that make sense together: LEDs on one
side, GPIOs of the GPIO header on another side, and DIP switches on
yet another side.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
Note that some of the LEDs pinmux configurations are kept in the
pinctrl node, because they are not used by the gpio-leds driver.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kirkwood iConnect Device Tree is currently using totally
meaningless names for the pinmux configuration: pmx_gpio_XY.
This patch fixes that by using some more meaningful names such as
pmx_button_power.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
