Russell King says:
====================
net: phylink: rearrange ovr_an_inband support
This series addresses the use of the ovr_an_inband flag, which is used
by two drivers to indicate to phylink that they wish to use inband mode
without firmware specifying inband mode.
The issue with ovr_an_inband is that it overrides not only PHY mode,
but also fixed-link mode. Both of the drivers that set this flag
contain code to detect when fixed-link mode will be used, and then
either avoid setting it or explicitly clear the flag. This is
wasteful when phylink already knows this.
Therefore, the approach taken in this patch set is to replace the
ovr_an_inband flag with a default_an_inband flag which means that
phylink defaults to MLO_AN_INBAND instead of MLO_AN_PHY, and will
allow that default to be overriden if firmware specifies a fixed-link.
This allows users of ovr_an_inband to be simplified.
What's more is this requires minimal changes in phylink to allow this
new mode of operation.
This series changes phylink, and also updates the two drivers
(fman_memac and stmmac), and then removes the unnecessary complexity
from the drivers.
This series may depend on the stmmac cleanup series I've posted
earlier - this is something I have not checked, but I currently have
these patches on top of that series.
====================
Link: https://lore.kernel.org/r/ZlctinnTT8Xhemsm@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Test ovr_an_inband before checking for the fixed-link properties, which
will allow ovr_an_inband to be overriden by a fixed link specification.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMq-00Ecqv-P8@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Rearrange phylink_parse_mode() a little so we can change how
phylink_config->ovr_an_inband works. This will allow the flag to be
tested before checking for the fixed link properties in the next patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMl-00Ecqp-K0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: stmmac: cleanups
This series removes various redundant items in the stmmac driver:
- the unused TBI and RTBI PCS flags
- the NULL pointer initialisations for PCS methods in dwxgmac2
- the stmmac_pcs_rane() method which is never called, and it's
associated implementations
- the redundant netif_carrier_off()s
Finally, it replaces asm/io.h with the preferred linux/io.h.
====================
Link: https://lore.kernel.org/r/Zlbp7xdUZAXblOZJ@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is incorrect to call netif_carrier_off(), or in fact any driver
teardown, before unregister_netdev() has been called.
unregister_netdev() unpublishes the network device from userspace, and
takes the interface down if it was up prior to returning. Therefore,
once the call has returned, we are guaranteed that .ndo_stop() will
have been called for an interface that was up. Phylink will take the
carrier down via phylink_stop(), making any manipulation of the carrier
in the remove path unnecessary.
In the stmmac_release() path, the netif_carrier_off() call follows the
call to phylink_stop(), so this call is redundant.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/E1sCErZ-00EOPx-PF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First of all the flags are never set by any of the driver parts. If nobody
have them set then the respective statements will always have the same
result. Thus the statements can be simplified or even dropped with no risk
to break things.
Secondly shall any of the TBI or RTBI flag is set the MDIO-bus
registration will be bypassed. Why? It really seems weird. It's perfectly
fine to have a TBI/RTBI-capable PHY configured over the MDIO bus
interface.
Based on the notes above the TBI/RTBI PCS flags can be freely dropped thus
simplifying the driver code.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/E1sCErK-00EOPf-EP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A comment in define_trace.h clearly states:
TRACE_INCLUDE_PATH if the path is something other than core kernel
vvvvvvvvvvvvvv
include/trace then this macro can define the path to use. Note, the path
is relative to define_trace.h, not the file including it. Full path names
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
for out of tree modules must be used.
fjes uses path relative to itself. Which (somehow) works most of
the time. Except when the kernel tree is "nested" in another
kernel tree, and ../drivers/net/fjes actually exists. In which
case build will use the header file from the wrong directory.
I've been trying to figure out why net NIPA builder is constantly
failing for the last 5 days, with:
include/trace/../../../drivers/net/fjes/fjes_trace.h:88:17: error: ‘__assign_str’ undeclared (first use in this function)
88 | __assign_str(err, err);
| ^~~~~~~~~~~~
when the line in the tree clearly has only one "err". NIPA does
indeed have "nested" trees, because it uses git work-trees and
the tree on the "outside" is not very up to date.
Link: https://lore.kernel.org/r/20240529023322.3467755-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recovery from broken states can be hard. If the LIF reset in
the fw_down path didn't work because the PCI link was broken,
the FW won't be in the right state for proper restart. We can
fire another LIF reset in the fw_up path to be sure things
are clean on restart.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240529000259.25775-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each object file contains information about which module it gets linked
into, so linking the same file into multiple modules now causes a warning:
scripts/Makefile.build:254: drivers/net/ethernet/hisilicon/hns3/Makefile: hns3_common/hclge_comm_cmd.o is added to multiple modules: hclge hclgevf
scripts/Makefile.build:254: drivers/net/ethernet/hisilicon/hns3/Makefile: hns3_common/hclge_comm_rss.o is added to multiple modules: hclge hclgevf
scripts/Makefile.build:254: drivers/net/ethernet/hisilicon/hns3/Makefile: hns3_common/hclge_comm_tqp_stats.o is added to multiple modules: hclge hclgevf
Change the way that hns3 is built by moving the three common files into a
separate module with exported symbols instead.
Fixes: 5f20be4e90 ("net: hns3: refactor hns3 makefile to support hns3_common module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528161603.2443125-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each object file contains information about which module it gets linked
into, so linking the same file into multiple modules now causes a warning:
scripts/Makefile.build:254: drivers/net/ethernet/marvell/octeontx2/nic/Makefile: otx2_devlink.o is added to multiple modules: rvu_nicpf rvu_nicvf
Change the way that octeontx2 ethernet is built by moving the common
file into a separate module with exported symbols instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528152527.2148092-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Joe Damato says:
====================
mlx4: Add support for netdev-genl API
There are no functional changes from v5, which I mistakenly sent right
after net-next was closed (oops). This revision, however, includes
Tariq's Reviewed-by tags of the v5 in each commit message. See the
changelog below.
This series adds support to mlx4 for the netdev-genl API which makes it
much easier for users and user programs to map NAPI IDs back to
ifindexes, queues, and IRQs. This is extremely useful for a number of
use cases, including epoll-based busy poll.
In addition, this series includes a patch to generate per-queue
statistics using the netlink API, as well.
To facilitate the stats, patch 1/3 adds a field "alloc_fail" to the ring
structure. This is incremented by the driver in an appropriate place and
used in patch 3/3 as alloc_fail.
Please note: I do not have access to mlx4 hardware, but I've been
working closely with Martin Karsten from University of Waterloo (CC'd)
who has very graciously tested my patches on their mlx4 hardware (hence
his Tested-by attribution in each commit). His latest research work is
particularly interesting [1] and this series helps to support that (and
future) work.
Martin re-test v4 using Jakub's suggested tool [2] and the
stats.pkt_byte_sum and stats.qstat_by_ifindex tests passed. He also
adjusted the queue count and re-ran test to confirm it still passed even
if the queue count was modified.
[1]: https://dl.acm.org/doi/pdf/10.1145/3626780
[2]: https://lore.kernel.org/lkml/20240423175718.4ad4dc5a@kernel.org/
====================
Link: https://lore.kernel.org/r/20240528181139.515070-1-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- gro: initialize network_offset in network layer
- tcp: reduce accepted window in NEW_SYN_RECV state
Current release - new code bugs:
- eth: mlx5e: do not use ptp structure for tx ts stats when not
initialized
- eth: ice: check for unregistering correct number of devlink params
Previous releases - regressions:
- bpf: Allow delete from sockmap/sockhash only if update is allowed
- sched: taprio: extend minimum interval restriction to entire cycle
too
- netfilter: ipset: add list flush to cancel_gc
- ipv4: fix address dump when IPv4 is disabled on an interface
- sock_map: avoid race between sock_map_close and sk_psock_put
- eth: mlx5: use mlx5_ipsec_rx_status_destroy to correctly delete
status rules
Previous releases - always broken:
- core: fix __dst_negative_advice() race
- bpf:
- fix multi-uprobe PID filtering logic
- fix pkt_type override upon netkit pass verdict
- netfilter: tproxy: bail out if IP has been disabled on the device
- af_unix: annotate data-race around unix_sk(sk)->addr
- eth: mlx5e: fix UDP GSO for encapsulated packets
- eth: idpf: don't enable NAPI and interrupts prior to allocating Rx
buffers
- eth: i40e: fully suspend and resume IO operations in EEH case
- eth: octeontx2-pf: free send queue buffers incase of leaf to inner
- eth: ipvlan: dont Use skb->sk in ipvlan_process_v{4,6}_outbound"
* tag 'net-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
netdev: add qstat for csum complete
ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
net: ena: Fix redundant device NUMA node override
ice: check for unregistering correct number of devlink params
ice: fix 200G PHY types to link speed mapping
i40e: Fully suspend and resume IO operations in EEH case
i40e: factoring out i40e_suspend/i40e_resume
e1000e: move force SMBUS near the end of enable_ulp function
net: dsa: microchip: fix RGMII error in KSZ DSA driver
ipv4: correctly iterate over the target netns in inet_dump_ifaddr()
net: fix __dst_negative_advice() race
nfc/nci: Add the inconsistency check between the input data length and count
MAINTAINERS: dwmac: starfive: update Maintainer
net/sched: taprio: extend minimum interval restriction to entire cycle too
net/sched: taprio: make q->picos_per_byte available to fill_sched_entry()
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
net: ti: icssg-prueth: Fix start counter for ft1 filter
sock_map: avoid race between sock_map_close and sk_psock_put
...
MD Danish Anwar says:
====================
Introduce switch mode support for ICSSG driver
This series adds support for switch-mode for ICSSG driver. This series
also introduces helper APIs to configure firmware maintained FDB
(Forwarding Database) and VLAN tables. These APIs are later used by ICSSG
driver in switch mode.
Now the driver will boot by default in dual EMAC mode. When first ICSSG
interface is added to bridge driver will still be in EMAC mode. As soon as
second ICSSG interface is added to same bridge, switch-mode will be
enabled and switch firmwares will be loaded to PRU cores. The driver will
remain in dual EMAC mode if ICSSG interfaces are added to two different
bridges or if two different interfaces (One ICSSG, one other) is added to
the same bridge. We'll only enable is_switch_mode flag when two ICSSG
interfaces are added to same bridge.
We start in dual MAC mode. Let's say lan0 and lan1 are ICSSG interfaces
ip link add name br0 type bridge
ip link set lan0 master br0
At this point, we get a CHANGEUPPER event. Only one port is a member of
the bridge, so we will still be in dual MAC mode.
ip link set lan1 master br0
We get a second CHANGEUPPER event, the second interface lan1 is also ICSSG
interface so we will set the is_switch_mode flag and when interfaces are
brought up again, ICSSG switch firmwares will be loaded to PRU Cores.
There are some other cases to consider as well.
ip link add name br0 type bridge
ip link add name br1 type bridge
ip link set lan0 master br0
ip link set ppp0 master br0
Here we are adding lan0 (ICSSG) and ppp0 (non ICSSG) to same bridge, as
they both are not ICSSG, we will still be running in dual EMAC mode.
ip link set lan1 master br1
ip link set vpn0 master br1
Here we are adding lan1 (ICSSG) and vpn0 (non ICSSG) to same bridge, as
they both are not ICSSG, we will still be running in dual EMAC mode.
This is v6 of the series.
Changes from v5 to v6:
*) Removed __packed from structures in icssg_config.h file.
*) Added RB tags of Andrew Lunn <andrew@lunn.ch> to patch 2/3 and patch
3/3 of this series.
Changes from v4 to v5:
*) Rebased on 6.10-rc1.
*) Dropped the RFC tag.
Changes from v3 to v4:
*) Added RFC tag as net-next is closed now.
*) Modified the driver to remove the need of bringing interfaces up / down
for enabling / disabling switch mode. Now switch mode can be enabled
without bringig interfaces up / down as requested by Andrew Lunn
<andrew@lunn.ch>
*) Modified commit message of patch 3/3.
Changes from v2 to v3:
*) Dropped RFC tag.
*) Used ether_addr_copy() instead of manually copying mac address using
for loop in patch 1/3 as suggested by Andrew Lunn <andrew@lunn.ch>
*) Added helper API icssg_fdb_setup() in patch 1/3 to reduce code
duplication as suggested by Andrew Lunn <andrew@lunn.ch>
*) In prueth_switchdev_stp_state_set() removed BR_STATE_LEARNING as
learning without forwarding is not supported by ICSSG firmware.
*) Used ether_addr_equal() wherever possible in patch 2/3 as suggested
by Andrew Lunn <andrew@lunn.ch>
*) Fixed typo "nit: s/prueth_switchdevice_nb/prueth_switchdev_nb/" in
patch 2/3 as suggested by Simon Horman <horms@kernel.org>
*) Squashed "#include "icssg_mii_rt.h" to patch 2/3 from patch 3/3 as
suggested by Simon Horman <horms@kernel.org>
*) Rebased on latest net-next/main.
Changes from v1 to v2:
*) Removed TAPRIO support patch from this series.
*) Stopped using devlink for enabling switch-mode as suggested by Andrew L
*) Added read_poll_timeout() in patch 1 / 3 as suggested by Andrew L.
v1 https://lore.kernel.org/all/20230830110847.1219515-4-danishanwar@ti.com/
v2 https://lore.kernel.org/all/20240118071005.1514498-1-danishanwar@ti.com/
v3 https://lore.kernel.org/all/20240327114054.1907278-1-danishanwar@ti.com/
v4 https://lore.kernel.org/all/20240515060320.2783244-1-danishanwar@ti.com/
v5 https://lore.kernel.org/all/20240527052738.152821-1-danishanwar@ti.com/
Thanks and Regards,
Md Danish Anwar
====================
Link: https://lore.kernel.org/r/20240528113734.379422-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for ICSSG switch firmware using existing Dual EMAC driver
with switchdev.
Limitations:
VLAN offloading is limited to 0-256 IDs.
MDB/FDB static entries are limited to 511 entries and different FDBs can
hash to same bucket and thus may not completely offloaded
Example assuming ETH1 and ETH2 as ICSSG2 interfaces:
Switch to ICSSG Switch mode:
ip link add name br0 type bridge
ip link set dev eth1 master br0
ip link set dev eth2 master br0
ip link set dev br0 up
bridge vlan add dev br0 vid 1 pvid untagged self
Going back to Dual EMAC mode:
ip link set dev br0 down
ip link set dev eth1 nomaster
ip link set dev eth2 nomaster
ip link del name br0 type bridge
By default, Dual EMAC firmware is loaded, and can be changed to switch
mode by above steps
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ICSSG can operating in switch mode with 2 ext port and 1 host port with
VLAN/FDB/MDB and STP offloading. Add switchdev based driver to
support the same.
Driver itself will be integrated with icssg_prueth in future commits
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce helper functions to configure firmware FDB tables, VLAN tables
and Port VLAN ID settings to aid adding Switch mode support.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent commit 0cfe71f45f ("netdev: add queue stats") added
a lot of useful stats, but only those immediately needed by virtio.
Presumably virtio does not support CHECKSUM_COMPLETE,
so statistic for that form of checksumming wasn't included.
Other drivers will definitely need it, in fact we expect it
to be needed in net-next soon (mlx5). So let's add the definition
of the counter for CHECKSUM_COMPLETE to uAPI in net already,
so that the counters are in a more natural order (all subsequent
counters have not been present in any released kernel, yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Fixes: 0cfe71f45f ("netdev: add queue stats")
Link: https://lore.kernel.org/r/20240529163547.3693194-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 syzbot reports that nf_reinject() could be called without
rcu_read_lock() when flushing pending packets at nfnetlink
queue removal, from Eric Dumazet.
Patch #2 flushes ipset list:set when canceling garbage collection to
reference to other lists to fix a race, from Jozsef Kadlecsik.
Patch #3 restores q-in-q matching with nft_payload by reverting
f6ae9f120d ("netfilter: nft_payload: add C-VLAN support").
Patch #4 fixes vlan mangling in skbuff when vlan offload is present
in skbuff, without this patch nft_payload corrupts packets
in this case.
Patch #5 fixes possible nul-deref in tproxy no IP address is found in
netdevice, reported by syzbot and patch from Florian Westphal.
Patch #6 removes a superfluous restriction which prevents loose fib
lookups from input and forward hooks, from Eric Garver.
My assessment is that patches #1, #2 and #5 address possible kernel
crash, anything else in this batch fixes broken features.
netfilter pull request 24-05-29
* tag 'nf-24-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
netfilter: nft_payload: restore vlan q-in-q match support
netfilter: ipset: Add list flush to cancel_gc
netfilter: nfnetlink_queue: acquire rcu_read_lock() in instance_destroy_rcu()
====================
Link: https://lore.kernel.org/r/20240528225519.1155786-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver overrides the NUMA node id of the device regardless of
whether it knows its correct value (often setting it to -1 even though
the node id is advertised in 'struct device'). This can lead to
suboptimal configurations.
This patch fixes this behavior and makes the shared memory allocation
functions use the NUMA node id advertised by the underlying device.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20240528170912.1204417-1-shayagr@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jacob Keller says:
====================
Intel Wired LAN Driver Updates 2024-05-28 (e1000e, i40e, ice) [part]
This series includes a variety of fixes that have been accumulating on the
Intel Wired LAN dev-queue.
Hui Wang provides a fix for suspend/resume on e1000e due to failure
to correctly setup the SMBUS in enable_ulp().
Thinh Tran provides a fix for EEH I/O suspend/resume on i40e to
ensure that I/O operations can continue after a resume. To avoid duplicate
code, the common logic is factored out of i40e_suspend and i40e_resume.
Paul Greenwalt provides a fix to correctly map the 200G PHY types to link
speeds in the ice driver.
Dave Ertman provides a fix correcting devlink parameter unregistration in
the event that the driver loads in safe mode and some of the parameters
were not registered.
====================
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-0-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On module load, the ice driver checks for the lack of a specific PF
capability to determine if it should reduce the number of devlink params
to register. One situation when this test returns true is when the
driver loads in safe mode. The same check is not present on the unload
path when devlink params are unregistered. This results in the driver
triggering a WARN_ON in the kernel devlink code.
The current check and code path uses a reduction in the number of elements
reported in the list of params. This is fragile and not good for future
maintaining.
Change the parameters to be held in two lists, one always registered and
one dependent on the check.
Add a symmetrical check in the unload path so that the correct parameters
are unregistered as well.
Fixes: 109eb29172 ("ice: Add tx_scheduling_layers devlink param")
CC: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-8-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When EEH events occurs, the callback functions in the i40e, which are
managed by the EEH driver, will completely suspend and resume all IO
operations.
- In the PCI error detected callback, replaced i40e_prep_for_reset()
with i40e_io_suspend(). The change is to fully suspend all I/O
operations
- In the PCI error slot reset callback, replaced pci_enable_device_mem()
with pci_enable_device(). This change enables both I/O and memory of
the device.
- In the PCI error resume callback, replaced i40e_handle_reset_warning()
with i40e_io_resume(). This change allows the system to resume I/O
operations
Fixes: a5f3d2c17b ("powerpc/pseries/pci: Add MSI domains")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Robert Thomas <rob.thomas@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-3-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two new functions, i40e_io_suspend() and i40e_io_resume(), have been
introduced. These functions were factored out from the existing
i40e_suspend() and i40e_resume() respectively. This factoring was
done due to concerns about the logic of the I40E_SUSPENSED state, which
caused the device to be unable to recover. The functions are now used
in the EEH handling for device suspend/resume callbacks.
The function i40e_enable_mc_magic_wake() has been moved ahead of
i40e_io_suspend() to ensure it is declared before being used.
Tested-by: Robert Thomas <rob.thomas@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-2-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 861e808602 ("e1000e: move force SMBUS from enable ulp
function to avoid PHY loss issue") introduces a regression on
PCH_MTP_I219_LM18 (PCIID: 0x8086550A). Without the referred commit, the
ethernet works well after suspend and resume, but after applying the
commit, the ethernet couldn't work anymore after the resume and the
dmesg shows that the NIC link changes to 10Mbps (1000Mbps originally):
[ 43.305084] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 10 Mbps Full Duplex, Flow Control: Rx/Tx
Without the commit, the force SMBUS code will not be executed if
"return 0" or "goto out" is executed in the enable_ulp(), and in my
case, the "goto out" is executed since FWSM_FW_VALID is set. But after
applying the commit, the force SMBUS code will be ran unconditionally.
Here move the force SMBUS code back to enable_ulp() and put it
immediately ahead of hw->phy.ops.release(hw), this could allow the
longest settling time as possible for interface in this function and
doesn't change the original code logic.
The issue was found on a Lenovo laptop with the ethernet hw as below:
00:1f.6 Ethernet controller [0200]: Intel Corporation Device [8086:550a]
(rev 20).
And this patch is verified (cable plug and unplug, system suspend
and resume) on Lenovo laptops with ethernet hw: [8086:550a],
[8086:550b], [8086:15bb], [8086:15be], [8086:1a1f], [8086:1a1c] and
[8086:0dc7].
Fixes: 861e808602 ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-1-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
