Currently, all kfd BOs use same destruction routine. But pinned
BOs are not unpinned properly. Separate them from general routine.
v2 (Felix):
Add safeguard to prevent user space from freeing signal BO.
Kunmap signal BO in the event of setting event page error.
Just kunmap signal BO to avoid duplicating the code.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The userptr can be unmapped by application and still registered to
driver, restore userptr work return user pages will get -EFAULT bad
address error. Pretend this error as succeed. GPU access this userptr
will have VM fault later, it is better than application soft hangs with
stalled user mode queues.
v2: squash in warning fix (Alex)
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When a GPU hits the bad_page_threshold, it will not be initialized by
the amdgpu driver. This means that the table cannot be cleared, nor can
information gathering be performed (getting serial number, BDF, etc).
If the bad_page_threshold kernel parameter is set to -2,
continue to initialize the GPU, while printing a warning to dmesg that
this action has been done
v2: squash in Luben's fix to restore RAS info reporting
Cc: Luben Tuikov <luben.tuikov@amd.com>
Cc: Mukul Joshi <Mukul.Joshi@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dmesg doesn't warn when the number of bad pages approaches the
threshold for page retirement. WARN when the number of bad pages
is at 90% or greater for easier checks and planning, instead of waiting
until the GPU is full of bad pages.
Cc: Luben Tuikov <luben.tuikov@amd.com>
Cc: Mukul Joshi <Mukul.Joshi@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add FourCCs for 10- and 12-bit red formats with padding to 16 bits.
They correspond to the V4L2 10- and 12-bit greyscale (V4L2_PIX_FMT_Y10
and V4L2_PIX_FMT_Y12) formats, as well as the Bayer formats with the
same bit depth (V4L2_PIX_FMT_SBGGR{10,12} and all other Bayer pattern
permutations).
These formats are not used by any kernel driver at this point, but need
to be exposed to applications by libcamera, which uses DRM FourCCs for
pixel formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027233140.12268-1-laurent.pinchart@ideasonboard.com
Some randconfig builds fail when drm/drm_bridge.h is not included
implicitly in this file:
drivers/gpu/drm/msm/dp/dp_parser.c:279:25: error: implicit declaration of function 'devm_drm_panel_bridge_add' [-Werror,-Wimplicit-function-declaration]
parser->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
Fixes: 4b296d15b3 ("drm/msm/dp: Allow attaching a drm_panel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211026083254.3396322-1-arnd@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clang warns:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:162:6: error: variable 'commit' is uninitialized when used here [-Werror,-Wuninitialized]
if (commit)
^~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:106:32: note: initialize the variable 'commit' to silence this warning
struct drm_crtc_commit *commit;
^
= NULL
1 error generated.
The assignment and use of commit in the main body of
dpu_crtc_set_crc_source() were removed from v1 to v2 but the call to
drm_crtc_commit_put() at the end was not. Do that now so there is no
more warning.
Fixes: 78d9b458cc ("drm/msm/dpu: Add CRC support for DPU")
Link: https://github.com/ClangBuiltLinux/linux/issues/1493
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211026142435.3606413-1-nathan@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
8b/10b encoding format requires to reserve the first slot for
recording metadata. Real data transmission starts from the second slot,
with a total of available 63 slots available.
In 128b/132b encoding format, metadata is transmitted separately
in LLCP packet before MTP. Real data transmission starts from
the first slot, with a total of 64 slots available.
v2:
* Move total/start slots to mst_state, and copy it to mst_mgr in
atomic_check
v3:
* Only keep the slot info on the mst_state
* add a start_slot parameter to the payload function, to facilitate non
atomic drivers (this is a temporary workaround and should be removed when
we are moving out the non atomic driver helpers)
v4:
*fixed typo and formatting
v5: (no functional changes)
* Fixed formatting in drm_dp_mst_update_slots()
* Reference mst_state instead of mst_state->mgr for debugging info
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
[v5 nitpicks]
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-3-lyude@redhat.com
Commit 110860541f ("mm/secretmem: use refcount_t instead of atomic_t")
attempted to fix the problem of secretmem_users wrapping to zero and
allowing suspend once again.
But it was reverted in commit 87066fdd2e ("Revert 'mm/secretmem: use
refcount_t instead of atomic_t'") because of the problems it caused - a
refcount_t was not semantically the right type to use.
Instead prevent secretmem_users from wrapping to zero by forbidding new
users if the number of users has wrapped from positive to negative.
This stops a long way short of reaching the necessary 4 billion users
where it wraps to zero again, so there's no need to be clever with
special anti-wrap types or checking the return value from atomic_inc().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Jordy Zomer <jordy@pwning.systems>
Cc: Kees Cook <keescook@chromium.org>,
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit efafec27c5 ("spi: Fix tegra20 build with CONFIG_PM=n") already
fixed the build without PM support once. There was an alternative fix
by Guenter in commit 2bab94090b ("spi: tegra20-slink: Declare runtime
suspend and resume functions conditionally"), and Mark then merged the
two correctly in ffb1e76f4f ("Merge tag 'v5.15-rc2' into spi-5.15").
But for some inexplicable reason, Mark then merged things _again_ in
commit 59c4e190b1 ("Merge tag 'v5.15-rc3' into spi-5.15"), and screwed
things up at that point, and the __maybe_unused attribute on
tegra_slink_runtime_resume() went missing.
Reinstate it, so that alpha (and other architectures without PM support)
builds cleanly again.
Btw, this is another prime example of how random back-merges are not
good. Just don't do them. Subsystem developers should not merge my
tree in any normal circumstances. Both of those merge commits pointed
to above are bad: even the one that got the merge result right doesn't
even mention _why_ it was done, and the one that got it wrong is
obviously broken.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
- Fix clang-related relocation warning in futex code
- Fix incorrect use of get_kernel_nofault()
- Fix bad code generation in __get_user_check() when kasan is enabled
- Ensure TLB function table is correctly aligned
- Remove duplicated string function definitions in decompressor
- Fix link-time orphan section warnings
- Fix old-style function prototype for arch_init_kprobes()
- Only warn about XIP address when not compile testing
- Handle BE32 big endian for keystone2 remapping
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9148/1: handle CONFIG_CPU_ENDIAN_BE32 in arch/arm/kernel/head.S
ARM: 9141/1: only warn about XIP address when not compile testing
ARM: 9139/1: kprobes: fix arch_init_kprobes() prototype
ARM: 9138/1: fix link warning with XIP + frame-pointer
ARM: 9134/1: remove duplicate memcpy() definition
ARM: 9133/1: mm: proc-macros: ensure *_tlb_fns are 4B aligned
ARM: 9132/1: Fix __get_user_check failure with ARM KASAN images
ARM: 9125/1: fix incorrect use of get_kernel_nofault()
ARM: 9122/1: select HAVE_FUTEX_CMPXCHG
Pull libata fix from Damien Le Moal:
"A single fix in this pull request addressing an invalid error code
return in the sata_mv driver (from Zheyu)"
* tag 'libata-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: sata_mv: Fix the error handling of mv_chip_id()
Pull pin control fixes from Linus Walleij:
"Some late pin control fixes, the most generally annoying will probably
be the AMD IRQ storm fix affecting the Microsoft surface.
Summary:
- Three fixes pertaining to Broadcom DT bindings. Some stuff didn't
work out as inteded, we need to back out
- A resume bug fix in the STM32 driver
- Disable and mask the interrupts on probe in the AMD pinctrl driver,
affecting Microsoft surface"
* tag 'pinctrl-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: amd: disable and mask interrupts on probe
pinctrl: stm32: use valid pin identifier in stm32_pinctrl_resume()
Revert "pinctrl: bcm: ns: support updated DT binding as syscon subnode"
dt-bindings: pinctrl: brcm,ns-pinmux: drop unneeded CRU from example
Revert "dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon"
My intel-ixp42x-welltech-epbx100 no longer boot since 4.14.
This is due to commit 463dbba4d1 ("ARM: 9104/2: Fix Keystone 2 kernel
mapping regression")
which forgot to handle CONFIG_CPU_ENDIAN_BE32 as possible BE config.
Suggested-by: Krzysztof Hałasa <khalasa@piap.pl>
Fixes: 463dbba4d1 ("ARM: 9104/2: Fix Keystone 2 kernel mapping regression")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Pull autofs fix from Al Viro:
"Fix for a braino of mine (in getting rid of open-coded
dentry_path_raw() in autofs a couple of cycles ago).
Mea culpa... Obvious -stable fodder"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
autofs: fix wait name hash calculation in autofs_wait()
Pull scheduler fix from Borislav Petkov:
"Reset clang's Shadow Call Stack on hotplug to prevent it from
overflowing"
* tag 'sched_urgent_for_v5.15_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/scs: Reset the shadow stack when idle_task_exit
Pull x86 fix from Borislav Petkov:
"A single change adding Dave Hansen to our maintainers team"
* tag 'x86_urgent_for_v5.15_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Add Dave Hansen to the x86 maintainer team
Pull ksmbd fixes from Steve French:
"Ten fixes for the ksmbd kernel server, for improved security and
additional buffer overflow checks:
- a security improvement to session establishment to reduce the
possibility of dictionary attacks
- fix to ensure that maximum i/o size negotiated in the protocol is
not less than 64K and not more than 8MB to better match expected
behavior
- fix for crediting (flow control) important to properly verify that
sufficient credits are available for the requested operation
- seven additional buffer overflow, buffer validation checks"
* tag '5.15-rc6-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: add buffer validation in session setup
ksmbd: throttle session setup failures to avoid dictionary attacks
ksmbd: validate OutputBufferLength of QUERY_DIR, QUERY_INFO, IOCTL requests
ksmbd: validate credit charge after validating SMB2 PDU body size
ksmbd: add buffer validation for smb direct
ksmbd: limit read/write/trans buffer size not to exceed 8MB
ksmbd: validate compound response buffer
ksmbd: fix potencial 32bit overflow from data area check in smb2_write
ksmbd: improve credits management
ksmbd: add validation in smb2_ioctl
Pull SCSI fixes from James Bottomley:
"Ten fixes, seven of which are in drivers.
The core fixes are one to fix a potential crash on resume, one to sort
out our reference count releases to avoid releasing in-use modules and
one to adjust the cmd per lun calculation to avoid an overflow in
hyper-v"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-pci: Force a full restore after suspend-to-disk
scsi: qla2xxx: Fix unmap of already freed sgl
scsi: qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()
scsi: qla2xxx: Return -ENOMEM if kzalloc() fails
scsi: sd: Fix crashes in sd_resume_runtime()
scsi: mpi3mr: Fix duplicate device entries when scanning through sysfs
scsi: core: Put LLD module refcnt after SCSI device is released
scsi: storvsc: Fix validation for unsolicited incoming packets
scsi: iscsi: Fix set_param() handling
scsi: core: Fix shost->cmd_per_lun calculation in scsi_add_host_with_dma()
We know the upper bound on # of mixers (ie. two), so lets just allocate
this on the stack.
Fixes:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:201
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
INFO: lockdep is turned off.
irq event stamp: 43642
hardirqs last enabled at (43641): [<ffffffe24dd276bc>] cpuidle_enter_state+0x158/0x25c
hardirqs last disabled at (43642): [<ffffffe24dfff450>] enter_el1_irq_or_nmi+0x10/0x1c
softirqs last enabled at (43620): [<ffffffe24d4103fc>] __do_softirq+0x1e4/0x464
softirqs last disabled at (43615): [<ffffffe24d48bd90>] __irq_exit_rcu+0x104/0x150
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.15.0-rc3-debug+ #105
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
Call trace:
dump_backtrace+0x0/0x18c
show_stack+0x24/0x30
dump_stack_lvl+0xa0/0xd4
dump_stack+0x18/0x34
___might_sleep+0x1e0/0x1f0
__might_sleep+0x78/0x8c
slab_pre_alloc_hook.constprop.0+0x48/0x6c
__kmalloc+0xc8/0x21c
dpu_crtc_vblank_callback+0x158/0x1f8
dpu_encoder_vblank_callback+0x70/0xc4
dpu_encoder_phys_vid_vblank_irq+0x50/0x12c
dpu_core_irq+0x1bc/0x1d0
dpu_irq+0x1c/0x28
msm_irq+0x34/0x40
__handle_irq_event_percpu+0x15c/0x308
handle_irq_event_percpu+0x3c/0x90
handle_irq_event+0x54/0x98
handle_level_irq+0xa0/0xd0
handle_irq_desc+0x2c/0x44
generic_handle_domain_irq+0x28/0x34
dpu_mdss_irq+0x90/0xe8
handle_irq_desc+0x2c/0x44
handle_domain_irq+0x54/0x80
gic_handle_irq+0xd4/0x148
call_on_irq_stack+0x2c/0x54
do_interrupt_handler+0x4c/0x64
el1_interrupt+0x30/0xd0
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x78/0x7c
arch_local_irq_enable+0xc/0x14
cpuidle_enter+0x44/0x5c
do_idle+0x248/0x268
cpu_startup_entry+0x30/0x48
rest_init+0x188/0x19c
arch_call_rest_init+0x1c/0x28
start_kernel+0x704/0x744
__primary_switched+0xc0/0xc8
Fixes: 78d9b458cc ("drm/msm/dpu: Add CRC support for DPU")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211023160016.3322052-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Pull block fixes from Jens Axboe:
"Fix for the cgroup code not ussing irq safe stats updates, and one fix
for an error handling condition in add_partition()"
* tag 'block-5.15-2021-10-22' of git://git.kernel.dk/linux-block:
block: fix incorrect references to disk objects
blk-cgroup: blk_cgroup_bio_start() should use irq-safe operations on blkg->iostat_cpu
Pull io_uring fixes from Jens Axboe:
"Two fixes for the max workers limit API that was introduced this
series: one fix for an issue with that code, and one fixing a linked
timeout regression in this series"
* tag 'io_uring-5.15-2021-10-22' of git://git.kernel.dk/linux-block:
io_uring: apply worker limits to previous users
io_uring: fix ltimeout unprep
io_uring: apply max_workers limit to all future users
io-wq: max_worker fixes
Pull fuse fixes from Miklos Szeredi:
"Syzbot discovered a race in case of reusing the fuse sb (introduced in
this cycle).
Fix it by doing the s_fs_info initialization at the proper place"
* tag 'fuse-fixes-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: clean up error exits in fuse_fill_super()
fuse: always initialize sb->s_fs_info
fuse: clean up fuse_mount destruction
fuse: get rid of fuse_put_super()
fuse: check s_root when destroying sb
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Include the correct header first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211018131929.2260087-1-arnd@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Pull ACPI fixes from Rafael Wysocki:
"These fix two regressions, one related to ACPI power resources
management and one that broke ACPI tools compilation.
Specifics:
- Stop turning off unused ACPI power resources in an unknown state to
address a regression introduced during the 5.14 cycle (Rafael
Wysocki).
- Fix an ACPI tools build issue introduced recently when the minimal
stdarg.h was added (Miguel Bernal Marin)"
* tag 'acpi-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: Do not turn off power resources in unknown state
ACPI: tools: fix compilation error
Pull more x86 kvm fixes from Paolo Bonzini:
- Cache coherency fix for SEV live migration
- Fix for instruction emulation with PKU
- fixes for rare delaying of interrupt delivery
- fix for SEV-ES buffer overflow
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: go over the sev_pio_data buffer in multiple passes if needed
KVM: SEV-ES: keep INS functions together
KVM: x86: remove unnecessary arguments from complete_emulator_pio_in
KVM: x86: split the two parts of emulator_pio_in
KVM: SEV-ES: clean up kvm_sev_es_ins/outs
KVM: x86: leave vcpu->arch.pio.count alone in emulator_pio_in_out
KVM: SEV-ES: rename guest_ins_data to sev_pio_data
KVM: SEV: Flush cache on non-coherent systems before RECEIVE_UPDATE_DATA
KVM: MMU: Reset mmu->pkru_mask to avoid stale data
KVM: nVMX: promptly process interrupts delivered while in guest mode
KVM: x86: check for interrupts before deciding whether to exit the fast path
On arcturus, not all platforms use PMFW based fan control. On such
ASICs fan control by PMFW will be disabled in PPTable. Disable hwmon
knobs for fan control also as it is not possible to report or control
fan speed on such platforms through driver.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The extended bits were not available for use on vega20 and
presumably arcturus as well.
Fixes: a0f9f85466 ("drm/amdgpu/nbio7.4: don't use GPU_HDP_FLUSH bit 12")
Reviewed-and-tested-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing check in smu_v11_0_init_display_count(),
Fixes: af3b89d3a6 ("drm/amdgpu/smu11.0: convert to IP version checking")
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The PIO scratch buffer is larger than a single page, and therefore
it is not possible to copy it in a single step to vcpu->arch/pio_data.
Bound each call to emulator_pio_in/out to a single page; keep
track of how many I/O operations are left in vcpu->arch.sev_pio_count,
so that the operation can be restarted in the complete_userspace_io
callback.
For OUT, this means that the previous kvm_sev_es_outs implementation
becomes an iterator of the loop, and we can consume the sev_pio_data
buffer before leaving to userspace.
For IN, instead, consuming the buffer and decreasing sev_pio_count
is always done in the complete_userspace_io callback, because that
is when the memcpy is done into sev_pio_data.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the diff a little nicer when we actually get to fixing
the bug. No functional change intended.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
complete_emulator_pio_in can expect that vcpu->arch.pio has been filled in,
and therefore does not need the size and count arguments. This makes things
nicer when the function is called directly from a complete_userspace_io
callback.
No functional change intended.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
emulator_pio_in handles both the case where the data is pending in
vcpu->arch.pio.count, and the case where I/O has to be done via either
an in-kernel device or a userspace exit. For SEV-ES we would like
to split these, to identify clearly the moment at which the
sev_pio_data is consumed. To this end, create two different
functions: __emulator_pio_in fills in vcpu->arch.pio.count, while
complete_emulator_pio_in clears it and releases vcpu->arch.pio.data.
Because this patch has to be backported, things are left a bit messy.
kernel_pio() operates on vcpu->arch.pio, which leads to emulator_pio_in()
having with two calls to complete_emulator_pio_in(). It will be fixed
in the next release.
While at it, remove the unused void* val argument of emulator_pio_in_out.
The function currently hardcodes vcpu->arch.pio_data as the
source/destination buffer, which sucks but will be fixed after the more
severe SEV-ES buffer overflow.
No functional change intended.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A few very small cleanups to the functions, smushed together because
the patch is already very small like this:
- inline emulator_pio_in_emulated and emulator_pio_out_emulated,
since we already have the vCPU
- remove the data argument and pull setting vcpu->arch.sev_pio_data into
the caller
- remove unnecessary clearing of vcpu->arch.pio.count when
emulation is done by the kernel (and therefore vcpu->arch.pio.count
is already clear on exit from emulator_pio_in and emulator_pio_out).
No functional change intended.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently emulator_pio_in clears vcpu->arch.pio.count twice if
emulator_pio_in_out performs kernel PIO. Move the clear into
emulator_pio_out where it is actually necessary.
No functional change intended.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
