Few minor fixes for omaps
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
ARM: dts: am335x-boneblack-common: fix memory size
Link: https://lore.kernel.org/r/pull-1579895109-287828@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The optee driver uses specific page table types to verify if a memory
region is normal. These types are not defined in nommu systems. Trying
to compile the driver in these systems results in a build error:
linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’:
linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared
(first use in this function); did you mean ‘PREEMPT_MASK’?
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~
PREEMPT_MASK
linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is
reported only once for each function it appears in
linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared
(first use in this function)
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~~~~~~~
Make the optee driver depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[jw: update commit title]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
BeagleBone Black series is equipped with 512MB RAM
whereas only 256MB is included from am335x-bone-common.dtsi
This leads to an issue with unusual setups when devicetree
is loaded by GRUB2 directly.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A fix for the Beelink A1 IR receiver setting the correct polarity.
* tag 'v5.5-rockchip-dtsfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix IR on Beelink A1
Link: https://lore.kernel.org/r/2054603.JKFSmqfO19@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf6 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 3feea8805d ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead1 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 93385546ba ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Fixes: a8039f2dd0 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ASPEED device tree fixes for 5.5
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
* tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
Link: https://lore.kernel.org/r/CACPK8XcjazgORXNZBU1ECMukXG4HA8D9VeDxiSPifDk_iB7_dw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With the new omap_prm driver added unconditionally, omap2 builds
fail when the reset controller subsystem is disabled:
drivers/soc/ti/omap_prm.o: In function `omap_prm_probe':
omap_prm.c:(.text+0x2d4): undefined reference to `devm_reset_controller_register'
Link: https://lore.kernel.org/r/20191216132132.3330811-1-arnd@arndb.de
Fixes: 3e99cb214f ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Selecting RESET_CONTROLLER is actually required, otherwise we
can get a link failure in the clock driver:
drivers/clk/davinci/psc.o: In function `__davinci_psc_register_clocks':
psc.c:(.text+0x9a0): undefined reference to `devm_reset_controller_register'
drivers/clk/davinci/psc-da850.o: In function `da850_psc0_init':
psc-da850.c:(.text+0x24): undefined reference to `reset_controller_add_lookup'
Link: https://lore.kernel.org/r/20191210195202.622734-1-arnd@arndb.de
Fixes: f962396ce2 ("ARM: davinci: support multiplatform build for ARM v5")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PCA9552 used for fan fault and presence information is at address
61h, not 60h.
Fixes: 2efc118ce3 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: rainier: Add i2c devices", which
was already applied to the tree.
Fixes: 9c44db7096 ("ARM: dts: aspeed: rainier: Add i2c devices")
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Tested-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable FMC and SPI
devices" which was already applied as part of "ARM: dts: aspeed: Add
Tacoma machine".
Fixes: 8737481e38 ("ARM: dts: aspeed: tacoma: Enable FMC and SPI devices")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable I2C busses", which
was already applied as part of "ARM: dts: aspeed: Add Tacoma machine".
Fixes: 606bcdde67 ("ARM: dts: aspeed: tacoma: Enable I2C busses")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The FIS nodes were placed incorrectly in the device tree.
Fixes: 0fe4e30478 ("ARM: dts: aspeed-g6: Describe FSI masters")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fixes for omaps for v5.5-rc cycle
Here are few fixes for v5.5-rc cycle:
- Two corner case fixes related to ti-sysc driver clock issues
- Fixes for am57xx dts for pcie gpios
- Beagle-x15 regulator dts fix
- Fix for wkup_m3_ipc driver race
* tag 'omap-for-v5.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot
ARM: dts: beagle-x15-common: Model 5V0 regulator
ARM: dts: am571x-idk: Fix gpios property to have the correct gpio number
ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes
bus: ti-sysc: Fix iterating over clocks
ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap
Link: https://lore.kernel.org/r/pull-1578418121-413328@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix OP-TEE multi page dynamic shm pool alloc
* tag 'tee-optee-fix-for-5.5' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
optee: Fix multi page dynamic shm pool alloc
Link: https://lore.kernel.org/r/20200103103710.GA3469@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
The register blocks don't occupy 4K. In fact, some blocks are packed
close to others and assuming they're 4K causes overlaps:
pxa2xx-i2c d4033800.i2c: can't request region for resource
[mem 0xd4033800-0xd40347ff]
Link: https://lore.kernel.org/r/20191220071443.247183-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Determined empirically, no documentation is available.
The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit f36797ee43 ("ARM: mmp/mmp2: dt: enable the clock")'
Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
optee_shm_register() expected pages to be passed as an array of page
pointers rather than as an array of contiguous pages. So fix that via
correctly passing pages as per expectation.
Fixes: a249dd200d ("tee: optee: Fix dynamic shm pool allocations")
Reported-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
The LSM9DS1 uses a high level interrupt.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to arm cpus binding doc,
"
On 32-bit ARM v7 or later systems this property is
required and matches the CPU MPIDR[23:0] register
bits.
Bits [23:0] in the reg cell must be set to
bits [23:0] in MPIDR.
All other bits in the reg cell must be set to 0.
"
In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"
Fixes: 20434dc92c ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DCFG block uses little endian. Fix it so that register access becomes
correct.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.
To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+
Fixes: d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Pull ARM SoC fixes from Olof Johansson:
"I didn't get a batch in this weekend, so here's what we queued up last
week and today.
- A couple of defconfigs add back debugfs -- it used to be implicitly
enabled through CONFIG_TRACING, but 0e4a459f56 ("tracing:
Remove unnecessary DEBUG_FS dependency") removed that.
- The rest are mostly minor fixlets of the usual kind; some DT
tweaks, a headerfile refactor that needs a build fix now, etc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: bcm: Add missing sentinel to bcm2711_compat[]
ARM: shmobile: defconfig: Restore debugfs support
bus: ti-sysc: Fix missing reset delay handling
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
ARM: mmp: include the correct cputype.h
ARM: dts: am437x-gp/epos-evm: fix panel compatible
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: bcm283x: Fix critical trip point
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
reset: Do not register resource data for missing resets
reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
reset: brcmstb: Remove resource checks
dt-bindings: reset: Fix brcmstb-reset example
...
Commit d878970f6c ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes: d878970f6c ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:
Unable to handle kernel paging request at virtual address ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<c011b348>] (clkdm_lookup+0x40/0x60)
[<c011b348>] (clkdm_lookup) from [<c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<c011cb84>] (ti_sysc_clkdm_init) from [<c03680a8>] (sysc_probe+0x948/0x117c)
[<c03680a8>] (sysc_probe) from [<c03d0af4>] (platform_drv_probe+0x48/0x98)
...
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
This pull request contains Broadcom ARM-based SoCs machine fixes for
5.5-rc1, please pull the following:
- H. Nikolaus adds a missing sentinel entry to the BCM2711 machine
descriptor compatible array which would make multiplatform kernels fail
to boot
* tag 'arm-soc/for-5.5/soc-fixes' of https://github.com/Broadcom/stblinux:
ARM: bcm: Add missing sentinel to bcm2711_compat[]
Link: https://lore.kernel.org/r/20191216035701.15534-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung fixes for v5.5
1. Restore debugfs support in exynos_defconfig (as now it is not
selected as dependency of tracing). Debugfs is required by systemd
and several tests.
2. Maintainers updates.
* tag 'samsung-fixes-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Restore debugfs support
MAINTAINERS: Include Samsung SoC serial driver in Samsung SoC entry
MAINTAINERS: Update Lukasz Luba's email address
Link: https://lore.kernel.org/r/20191215121316.32091-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
