Fixes a logic issue in mlxreg_lc_completion_notify() where the
intention was to check if MLXREG_LC_POWERED flag is not set before
powering on the device.
The original code used "state & ~MLXREG_LC_POWERED" to check for the
absence of the POWERED bit. However this condition evaluates to true
even when other bits are set, leading to potentially incorrect
behavior.
Corrected the logic to explicitly check for the absence of
MLXREG_LC_POWERED using !(state & MLXREG_LC_POWERED).
Fixes: 62f9529b8d ("platform/mellanox: mlxreg-lc: Add initial support for Nvidia line card devices")
Suggested-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://lore.kernel.org/r/20250630105812.601014-1-alok.a.tiwari@oracle.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
A new header fch.h was created to store registers used by different AMD
drivers. This header was included by i2c-piix4 in
commit 624b0d5696 ("i2c: piix4, x86/platform: Move the SB800 PIIX4 FCH
definitions to <asm/amd/fch.h>"). To prevent compile failures on non-x86
archs i2c-piix4 was set to only compile on x86 by commit 7e173eb82a
("i2c: piix4: Make CONFIG_I2C_PIIX4 dependent on CONFIG_X86").
This was not a good decision because loongarch and mips both actually
support i2c-piix4 and set it enabled in the defconfig.
Move the header to a location accessible by all architectures.
Fixes: 624b0d5696 ("i2c: piix4, x86/platform: Move the SB800 PIIX4 FCH definitions to <asm/amd/fch.h>")
Suggested-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250610205817.3912944-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Existing swnode graph format is specific to sensor device
and is causing conflicts when accessing standard property
variables outside the sensor driver.
To address this issue, enhanced swnode graph format with
dedicated nodes for i2c and isp devices, with sensor node
added as child to i2c node. This approach allows to have
standard property variables (ex: 'clock-frequency') with
values applicable for each of the devices (sensor, i2c and
isp).
ACPI device driver_data handle is also initialized with root
camera swnode to access the property variables in the graph
in isp and i2c drivers.
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250618202958.3934822-1-pratap.nirujogi@amd.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
It turns out that the Windows WMI-ACPI driver always enables/disables
WMI events regardless of whether they are marked as expensive or not.
This finding is further reinforced when reading the documentation of
the WMI_FUNCTION_CONTROL_CALLBACK callback used by Windows drivers
for enabling/disabling WMI devices:
The DpWmiFunctionControl routine enables or disables
notification of events, and enables or disables data
collection for data blocks that the driver registered
as expensive to collect.
Follow this behavior to fix the WMI event used for reporting hotkey
events on the Dell Latitude 5400 and likely many more devices.
Reported-by: Dmytro Bagrii <dimich.dmb@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220246
Tested-by: Dmytro Bagrii <dimich.dmb@gmail.com>
Fixes: 656f0961d1 ("platform/x86: wmi: Rework WCxx/WExx ACPI method handling")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250619221440.6737-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Without explicitly setting a parent for the watchdog device, the device is
registered with a NULL parent. This causes device_add() (called internally
by devm_watchdog_register_device()) to register the device under
/sys/devices/virtual, since no parent is provided. The result is:
DEVPATH=/devices/virtual/watchdog/watchdog0
To fix this, assign &pdev->dev as the parent of the watchdog device before
calling devm_watchdog_register_device(). This ensures the device is
associated with the Portwell EC platform device and placed correctly in
sysfs as:
DEVPATH=/devices/platform/portwell-ec/watchdog/watchdog0
This aligns the device hierarchy with expectations and avoids misplacement
under the virtual class.
Fixes: 8357967533 ("platform/x86: portwell-ec: Add GPIO and WDT driver for Portwell EC")
Signed-off-by: Ivan Hu <ivan.hu@canonical.com>
Link: https://lore.kernel.org/r/20250616074819.63547-1-ivan.hu@canonical.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Using a string variable in place of a format string causes a W=1 build warning:
drivers/platform/x86/intel/uncore-frequency/uncore-frequency-common.c:61:40: error: format string is not a string literal (potentially insecure) [-Werror,-Wformat-security]
61 | length += sysfs_emit_at(buf, length, agent_name[agent]);
| ^~~~~~~~~~~~~~~~~
Use the safer "%s" format string to print it instead.
Fixes: b98fa870fc ("platform/x86/intel-uncore-freq: Add attributes to show agent types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20250610093459.2646337-1-arnd@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The dell_rbu driver will use memset() to clear the data held by each
packet when it is no longer needed (when the driver is unloaded, the
packet size is changed, etc).
The amount of memory that is cleared (before this patch) is the normal
packet size. However, the last packet in the list may be smaller.
Fix this to only clear the memory actually used by each packet, to prevent
it from writing past the end of data buffer.
Because the packet data buffers are allocated with __get_free_pages() (in
page-sized increments), this bug could only result in a buffer being
overwritten when a packet size larger than one page is used. The only user
of the dell_rbu module should be the Dell BIOS update program, which uses
a packet size of 4096, so no issues should be seen without the patch, it
just blocks the possiblity.
Fixes: 6c54c28e69 ("[PATCH] dell_rbu: new Dell BIOS update driver")
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Link: https://lore.kernel.org/r/20250609184659.7210-5-stuart.w.hayes@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Currently hsmp_send_message() uses down_timeout() with a 100ms timeout
to take the semaphore. However __hsmp_send_message(), the content of the
critical section, has a sleep in it. On systems with significantly
delayed scheduling behaviour this may take over 100ms.
Convert this method to down_interruptible(). Leave the error handling
the same as the documentation currently is not specific about what error
is returned.
Previous behaviour: a caller who competes with another caller stuck in
the critical section due to scheduler delays would receive -ETIME.
New behaviour: a caller who competes with another caller stuck in the
critical section due to scheduler delays will complete successfully.
Reviewed-by: Suma Hegde <suma.hegde@amd.com>
Tested-by: Suma Hegde <suma.hegde@amd.com>
Signed-off-by: Jake Hillion <jake@hillion.co.uk>
Link: https://lore.kernel.org/r/20250605-amd-hsmp-v2-2-a811bc3dd74a@hillion.co.uk
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
__hsmp_send_message sleeps between result read attempts and has a
timeout of 100ms. Under extreme load it's possible for these sleeps to
take a long time, exceeding the 100ms. In this case the current code
does not check the register and fails with ETIMEDOUT.
Refactor the loop to ensure there is at least one read of the register
after a sleep of any duration. This removes instances of ETIMEDOUT with
a single caller, even with a misbehaving scheduler. Tested on AMD
Bergamo machines.
Suggested-by: Blaise Sanouillet <linux@blaise.sanouillet.com>
Reviewed-by: Suma Hegde <suma.hegde@amd.com>
Tested-by: Suma Hegde <suma.hegde@amd.com>
Signed-off-by: Jake Hillion <jake@hillion.co.uk>
Link: https://lore.kernel.org/r/20250605-amd-hsmp-v2-1-a811bc3dd74a@hillion.co.uk
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The area of memory that contains the metrics table may contain garbage
when the cycle starts. This normally doesn't matter because the cycle
itself will populate it with valid data, however commit 9f5595d5f0
("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep
cycles") started to use it during the check() phase. Depending upon
what garbage is in the table it's possible that the system will wait
2.5 seconds for even the first cycle, which will be visible to a user.
To prevent this from happening explicitly clear the table when logging
is started.
Fixes: 9f5595d5f0 ("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep cycles")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250603132412.3555302-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
It was reported that ideapad-laptop sometimes causes some recent (since
2024) Lenovo ThinkBook models shut down when:
- suspending/resuming
- closing/opening the lid
- (dis)connecting a charger
- reading/writing some sysfs properties, e.g., fan_mode, touchpad
- pressing down some Fn keys, e.g., Brightness Up/Down (Fn+F5/F6)
- (seldom) loading the kmod
The issue has existed since the launch day of such models, and there
have been some out-of-tree workarounds (see Link:) for the issue. One
disables some functionalities, while another one simply shortens
IDEAPAD_EC_TIMEOUT. The disabled functionalities have read_ec_data() in
their call chains, which calls schedule() between each poll.
It turns out that these models suffer from the indeterminacy of
schedule() because of their low tolerance for being polled too
frequently. Sometimes schedule() returns too soon due to the lack of
ready tasks, causing the margin between two polls to be too short.
In this case, the command is somehow aborted, and too many subsequent
polls (they poll for "nothing!") may eventually break the state machine
in the EC, resulting in a hard shutdown. This explains why shortening
IDEAPAD_EC_TIMEOUT works around the issue - it reduces the total number
of polls sent to the EC.
Even when it doesn't lead to a shutdown, frequent polls may also disturb
the ongoing operation and notably delay (+ 10-20ms) the availability of
EC response. This phenomenon is unlikely to be exclusive to the models
mentioned above, so dropping the schedule() manner should also slightly
improve the responsiveness of various models.
Fix these issues by migrating to usleep_range(150, 300). The interval is
chosen to add some margin to the minimal 50us and considering EC
responses are usually available after 150-2500us based on my test. It
should be enough to fix these issues on all models subject to the EC bug
without introducing latency on other models.
Tested on ThinkBook 14 G7+ ASP and solved both issues. No regression was
introduced in the test on a model without the EC bug (ThinkBook X IMH,
thanks Eric).
Link: 6c5db18c9e
Link: 42d1e68e50
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218771
Fixes: 6a09f21dd1 ("ideapad: add ACPI helpers")
Cc: stable@vger.kernel.org
Tested-by: Felix Yan <felixonmars@archlinux.org>
Tested-by: Eric Long <i@hack3r.moe>
Tested-by: Jianfei Zhang <zhangjianfei3@gmail.com>
Tested-by: Mingcong Bai <jeffbai@aosc.io>
Tested-by: Minh Le <minhld139@gmail.com>
Tested-by: Sicheng Zhu <Emmet_Z@outlook.com>
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://lore.kernel.org/r/20250525201833.37939-1-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Pull timer fix from Thomas Gleixner:
"Add the missing seq_file forward declaration in the timer namespace
header"
* tag 'timers-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timens: Add struct seq_file forward declaration
Add initial DMR support, which required smarter RAPL probe
Fix AMD MSR RAPL energy reporting
Add RAPL power limit configuration output
Minor fixes
Signed-off-by: Len Brown <len.brown@intel.com>
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
