The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.
Prepare support for the I2C Master Hub variant by moving the required
clocks list to a new desc struct then passing it through the compatible
match data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.
Document the I2C Serial Engine variant used within the I2C Master
Hub Wrapper.
This serial engine variant lacks DMA support, requires a core clock,
and since DMA support is lacking the memory interconnect path isn't
needed.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.
Document the variant compatible, forbid UART and SPI sub-nodes,
and remove requirement for the Master AHB clock and iommu property.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The RIIC block on the RZ/Five SoC is identical to one found on the RZ/G2UL
SoC. "renesas,riic-r9a07g043" compatible string will be used on the
RZ/Five SoC so to make this clear, update the comment to include RZ/Five
SoC.
No driver changes are required as generic compatible string
"renesas,riic-rz" will be used as a fallback on RZ/Five SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Set ACPI node as the primary fwnode of I2C adapter to allow
enumeration of child devices from the ACPI table
Signed-off-by: Zubair Waheed <zwaheed@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On my x05 laptop I got:
Memory type 0x12 not supported yet, not instantiating SPD
Adding the 0x12 case lead to a successful instantiated SPD AT24 EEPROM.
i801_smbus 0000:00:1f.3: SMBus using polling
i2c i2c-6: 2/2 memory slots populated (from DMI)
at24 6-0050: 256 byte spd EEPROM, read-only
i2c i2c-6: Successfully instantiated SPD at 0x50
at24 6-0051: 256 byte spd EEPROM, read-only
And then, I decoded it successfully via decode-dimms.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds IRQ support to the PASemi I2C controller driver to
increase the performace of I2C transactions on platforms with PASemi I2C
controllers. While primarily intended for Apple silicon platforms, this
patch should also help in enabling IRQ support for older PASemi hardware
as well should the need arise.
This version of the patch has been tested on an M1 Ultra Mac Studio,
as well as an M1 MacBook Pro, and userspace launches successfully
while using the IRQ path for I2C transactions.
Signed-off-by: Arminder Singh <arminders208@outlook.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DW_IC_COMP_VERSION register contains the ASCII representation of the
Synopsys component version. Here 0x3131312A == "111*" means version
1.11* required for DW_IC_SDA_HOLD register availability where '*' means
any letter starting from 'a'.
DW_IC_COMP_TYPE is constant and is derived from two ASCII letters "DW"
followed by a 16-bit unsigned number.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 90312351fd ("i2c: designware: MASTER mode as separated driver")
introduced disable_int pointer but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable_int() and scope is inside the same kernel module.
Since i2c_dw_disable_int() is just masking interrupts and the direct
DW_IC_INTR_MASK register write looks more clear in the code use that and
remove it from common code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In my opinion a few lines of spurious interrupt detection code can be
moved to the actual master interrupt handling function i2c_dw_isr()
without hurting readability.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It is kind of needless to print interrupt status when code immediately
after that finds interrupt was not originating from this device.
Therefore move it after spurious interrupt detection.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Do not return with interrupt handled if host controller is off and thus
interrupt is originating from other device or is spurious.
Add a check to detect when controller is runtime suspended or
transitioning/reset. In latter case all raw interrupt status register
bits may read one. In both cases return IRQ_NONE to indicate interrupt
was not from this device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Interrupt processing code in i2c-designware-slave.c is bit more readable
if not divided into another subroutine. Also explicit IRQ_NONE and
IRQ_HANDLED return values are more obvious.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Writes from I2C bus often fail when testing the i2c-designware-slave.c
with the slave-eeprom backend. The same writes work correctly when
testing with a real 24c02 EEPROM chip.
In the tests below an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6.
1. i2cset -y 6 0x65 0x00 0x55
Single byte 0x55 write into address 0x00. No data goes into simulated
EEPROM. Debug prints from the i2c_dw_irq_handler_slave():
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
2. i2ctransfer -y 6 w9@0x65 0x00 0xff-
Write 8 bytes with decrementing value starting from 0xff at address 0x00
and forward. Only some of the data goes into arbitrary addresses.
Content is something like below but varies:
00000000 f9 f8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000050 00 00 00 00 00 00 ff fe 00 00 00 00 00 00 00 00 |................|
000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fb fa |................|
In this case debug prints were:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x510 : INTR_STAT=0x0
Both cases show there is more data coming from the receive FIFO still
after detecting the STOP condition. This can be seen from interrupt
status bits DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4).
Perhaps due interrupt latencies the receive FIFO is not read fast
enough, STOP detection happens synchronously when it occurs on the I2C
bus and the DW_IC_INTR_RX_FULL keeps coming as long as there are more
bytes in the receive FIFO.
Fix this by reading the receive FIFO completely empty whenever
DW_IC_INTR_RX_FULL occurs. Use RFNE, Receive FIFO Not Empty bit in the
DW_IC_STATUS register to loop through bytes in the FIFO.
While at it do not test the return code from i2c_slave_event() for the
I2C_SLAVE_WRITE_RECEIVED since to my understanding this hardware cannot
generate NACK to incoming bytes and debug print itself does not have
much value.
Reported-by: Tian Ye <tianye@sugon.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some read types from I2C bus don't work correctly when testing the
i2c-designware-slave.c with the slave-eeprom backend. The same reads
work correctly when testing with a real 24c02 EEPROM chip.
In the following tests an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6:
1. i2cdump -y 6 0x65 b (OK)
Random read. Each byte are read using a byte address write with a
current address read in a same message.
2. i2cdump -y 6 0x65 c (OK, was NOK before commit 3b5f7f10ff when it
was repeating the 1st byte)
Repeated current address read. One byte address write message
followed by repeated current address read messages.
3. i2cdump -y 6 0x65 i (NOK, each 32 byte block repeats the 1st byte of
block)
Sequential read using SMBus Block Read. For each 32 byte block a byte
address write followed by 32 sequental reads in a same message.
These findings are explained because the implementation has had a
mismatch between hardware interrupts and what I2C slave events should be
sent after those interrupts. Despite that the case 1 happened to have
always the I2C slave events sent to a right order with a right data
between backend and the I2C bus.
Hardware generates the DW_IC_INTR_RD_REQ interrupt when another host is
attempting to read and for sequential reads after. DW_IC_INTR_RX_DONE
occurs when host does not acknowledge a transmitted byte which is an
indication the end of transmission.
Those interrupts do not match directly with I2C_SLAVE_READ_REQUESTED and
I2C_SLAVE_READ_PROCESSED events which is how the code was and is
practically using them. The slave-eeprom backend increases the buffer
index with the I2C_SLAVE_READ_PROCESSED event and returns the data from
current index when receiving only the I2C_SLAVE_READ_REQUESTED event.
That explains the repeated bytes in case 3 and also case 2 before
commit 3b5f7f10ff ("i2c: designware: slave should do WRITE_REQUESTED
before WRITE_RECEIVED").
Patch fixes the case 3 while keep cases 1 and 2 working with following
changes:
- First DW_IC_INTR_RD_REQ interrupt will change the state machine to
read in progress state, send I2C_SLAVE_READ_REQUESTED event and
transmit the first byte from backend
- Subsequent DW_IC_INTR_RD_REQ interrupts will send
I2C_SLAVE_READ_PROCESSED events and transmit next bytes from backend
- STOP won't change the state machine. Otherwise case 2 won't work since
we cannot distinguish current address read from sequentiel read
- DW_IC_INTR_RX_DONE interrupt is needless since there is no mechanism
to inform it to a backend. It cannot be used to change state machine
at the end of read either due the same reason than above
- Next host write to us will change the state machine from read to write
in progress state
- STATUS_WRITE_IN_PROGRESS and STATUS_READ_IN_PROGRESS are considered
now to be status flags not the state of the driver. This is how we
treat them in i2c-designware-master.c
While at it do not test the return code from i2c_slave_event() for
I2C_SLAVE_READ_REQUESTED and I2C_SLAVE_READ_PROCESSED since it returns
always 0.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C controller IP used in the Allwinner F1C100s series of SoCs is
compatible with the ones used in the other Allwinner SoCs.
Add an F1C100s specific compatible string to the list of existing names.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To make the code easier to understand, add longer names to the
definitions of register fields. These longer names are based on source
code published by DELL/AESS for WPCM450, but should apply just as well
to NPCM7xx and NPCM8xx.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The unlabelled registers NPCM_I2CCTL4 to NPCM_I2CSCLHT overlap with the
bank 1 registers below, and they are accessed after selecting bank 0, so
they clearly belong to bank 0.
Move them together with the other bank 0 registers, and move the
unrelated definition of npcm_i2caddr down to keep the banked registers
in one piece.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull fbdev fixes from Helge Deller:
"A use-after-free bugfix in the smscufx driver and various minor error
path fixes, smaller build fixes, sysfs fixes and typos in comments in
the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
drivers"
* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: cyber2000fb: fix missing pci_disable_device()
fbdev: sisfb: use explicitly signed char
fbdev: smscufx: Fix several use-after-free bugs
fbdev: xilinxfb: Make xilinxfb_release() return void
fbdev: sisfb: fix repeated word in comment
fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
fbdev: da8xx-fb: Fix error handling in .remove()
fbdev: MIPS supports iomem addresses
Pull char/misc fixes from Greg KH:
"Some small driver fixes for 6.1-rc3. They include:
- iio driver bugfixes
- counter driver bugfixes
- coresight bugfixes, including a revert and then a second fix to get
it right.
All of these have been in linux-next with no reported problems"
* tag 'char-misc-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
misc: sgi-gru: use explicitly signed char
coresight: cti: Fix hang in cti_disable_hw()
Revert "coresight: cti: Fix hang in cti_disable_hw()"
counter: 104-quad-8: Fix race getting function mode and direction
counter: microchip-tcb-capture: Handle Signal1 read and Synapse
coresight: cti: Fix hang in cti_disable_hw()
coresight: Fix possible deadlock with lock dependency
counter: ti-ecap-capture: fix IS_ERR() vs NULL check
counter: Reduce DEFINE_COUNTER_ARRAY_POLARITY() to defining counter_array
iio: bmc150-accel-core: Fix unsafe buffer attributes
iio: adxl367: Fix unsafe buffer attributes
iio: adxl372: Fix unsafe buffer attributes
iio: at91-sama5d2_adc: Fix unsafe buffer attributes
iio: temperature: ltc2983: allocate iio channels once
tools: iio: iio_utils: fix digit calculation
iio: adc: stm32-adc: fix channel sampling time init
iio: adc: mcp3911: mask out device ID in debug prints
iio: adc: mcp3911: use correct id bits
iio: adc: mcp3911: return proper error code on failure to allocate trigger
iio: adc: mcp3911: fix sizeof() vs ARRAY_SIZE() bug
...
Pull USB fixes from Greg KH:
"A few small USB fixes for 6.1-rc3. Include in here are:
- MAINTAINERS update, including a big one for the USB gadget
subsystem. Many thanks to Felipe for all of the years of hard work
he has done on this codebase, it was greatly appreciated.
- dwc3 driver fixes for reported problems.
- xhci driver fixes for reported problems.
- typec driver fixes for minor issues
- uvc gadget driver change, and then revert as it wasn't relevant for
6.1-final, as it is a new feature and people are still reviewing
and modifying it.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: gadget: Don't set IMI for no_interrupt
usb: dwc3: gadget: Stop processing more requests on IMI
Revert "usb: gadget: uvc: limit isoc_sg to super speed gadgets"
xhci: Remove device endpoints from bandwidth list when freeing the device
xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
xhci: Add quirk to reset host back to default state at shutdown
usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96 controller
usb: dwc3: st: Rely on child's compatible instead of name
usb: gadget: uvc: limit isoc_sg to super speed gadgets
usb: bdc: change state when port disconnected
usb: typec: ucsi: acpi: Implement resume callback
usb: typec: ucsi: Check the connection on resume
usb: gadget: aspeed: Fix probe regression
usb: gadget: uvc: fix sg handling during video encode
usb: gadget: uvc: fix sg handling in error case
usb: gadget: uvc: fix dropped frame after missed isoc
usb: dwc3: gadget: Don't delay End Transfer on delayed_status
usb: dwc3: Don't switch OTG -> peripheral if extcon is present
MAINTAINERS: Update maintainers for broadcom USB
MAINTAINERS: move USB gadget and phy entries under the main USB entry
Pull gpio fixes from Bartosz Golaszewski:
- convert gpio-tegra to using an immutable irqchip
- MAINTAINERS update
* tag 'gpio-fixes-for-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
MAINTAINERS: Change myself to a maintainer
gpio: tegra: Convert to immutable irq chip
Pull perf fixes from Borislav Petkov:
- Rename a perf memory level event define to denote it is of CXL type
- Add Alder and Raptor Lakes support to RAPL
- Make sure raw sample data is output with tracepoints
* tag 'perf_urgent_for_v6.1_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/mem: Rename PERF_MEM_LVLNUM_EXTN_MEM to PERF_MEM_LVLNUM_CXL
perf/x86/rapl: Add support for Intel Raptor Lake
perf/x86/rapl: Add support for Intel AlderLake-N
perf: Fix missing raw data on tracepoint events
Pull LoongArch fixes from Huacai Chen:
"Remove unused kernel stack padding, fix some build errors/warnings and
two bugs in laptop platform driver"
* tag 'loongarch-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
platform/loongarch: laptop: Fix possible UAF and simplify generic_acpi_laptop_init()
platform/loongarch: laptop: Adjust resume order for loongson_hotkey_resume()
LoongArch: BPF: Avoid declare variables in switch-case
LoongArch: Use flexible-array member instead of zero-length array
LoongArch: Remove unused kernel stack padding
Pull cifs fixes from Steve French:
- use after free fix for reconnect race
- two memory leak fixes
* tag '6.1-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix use-after-free caused by invalid pointer `hostname`
cifs: Fix pages leak when writedata alloc failed in cifs_write_from_iter()
cifs: Fix pages array leak when writedata alloc failed in cifs_writedata_alloc()
Pull random number generator fix from Jason Donenfeld:
"One fix from Jean-Philippe Brucker, addressing a regression in which
early boot code on ARM64 would use the non-_early variant of the
arch_get_random family of functions, resulting in the architectural
random number generator appearing unavailable during that early phase
of boot.
The fix simply changes arch_get_random*() to arch_get_random*_early().
This distinction between these two functions is a bit of an old wart
I'm not a fan of, and for 6.2 I'll see if I can make obsolete the
_early variant, so that one function does the right thing in all
contexts without overhead"
* tag 'random-6.1-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: use arch_get_random*_early() in random_init()
Pull SCSI fixes from James Bottomley:
"Varions small fixes, all in drivers.
Some of these arrived during the merge window and got held over to
make sure of testing on the -rc tree.
The biggest change is for standards conformance in the target driver,
closely followed by a set of bug fixes in megaraid_sas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: ufs: core: Fix typo in comment
scsi: mpi3mr: Select CONFIG_SCSI_SAS_ATTRS
scsi: ufs: core: Fix typo for register name in comments
scsi: pm80xx: Display proc_name in sysfs
scsi: ufs: core: Fix the error log in ufshcd_query_flag_retry()
scsi: ufs: core: Remove unneeded casts from void *
scsi: lpfc: Fix spelling mistake "unsolicted" -> "unsolicited"
scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
scsi: target: iblock: Fold iblock_emulate_read_cap_with_block_size() into iblock_get_blocks()
scsi: qla2xxx: Fix serialization of DCBX TLV data request
scsi: ufs: qcom: Remove redundant dev_err() call
scsi: megaraid_sas: Move megasas_dbg_lvl init to megasas_init()
scsi: megaraid_sas: Remove unnecessary memset()
scsi: megaraid_sas: Simplify megasas_update_device_list
scsi: megaraid_sas: Correct an error message
scsi: megaraid_sas: Correct value passed to scsi_device_lookup()
scsi: target: core: UA on all LUNs after reset
scsi: target: core: New key must be used for moved PR
scsi: target: core: Abort all preempted regs if requested
scsi: target: core: Fix memory leak in preempt_and_abort
...
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- make the multipath dma alignment match the non-multipath one
(Keith Busch)
- fix a bogus use of sg_init_marker() (Nam Cao)
- fix circulr locking in nvme-tcp (Sagi Grimberg)
- Initialization fix for requests allocated via the special hw queue
allocator (John)
- Fix for a regression added in this release with the batched
completions of end_io backed requests (Ming)
- Error handling leak fix for rbd (Yang)
- Error handling leak fix for add_disk() failure (Yu)
* tag 'block-6.1-2022-10-28' of git://git.kernel.dk/linux:
blk-mq: Properly init requests from blk_mq_alloc_request_hctx()
blk-mq: don't add non-pt request with ->end_io to batch
rbd: fix possible memory leak in rbd_sysfs_init()
nvme-multipath: set queue dma alignment to 3
nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
nvme-tcp: replace sg_init_marker() with sg_init_table()
block: fix memory leak for elevator on add_disk failure
Pull io_uring fix from Jens Axboe:
"Just a fix for a locking regression introduced with the deferred
task_work running from this merge window"
* tag 'io_uring-6.1-2022-10-28' of git://git.kernel.dk/linux:
io_uring: unlock if __io_run_local_work locked inside
io_uring: use io_run_local_work_locked helper
Pull misc hotfixes from Andrew Morton:
"Eight fix pre-6.0 bugs and the remainder address issues which were
introduced in the 6.1-rc merge cycle, or address issues which aren't
considered sufficiently serious to warrant a -stable backport"
* tag 'mm-hotfixes-stable-2022-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (23 commits)
mm: multi-gen LRU: move lru_gen_add_mm() out of IRQ-off region
lib: maple_tree: remove unneeded initialization in mtree_range_walk()
mmap: fix remap_file_pages() regression
mm/shmem: ensure proper fallback if page faults
mm/userfaultfd: replace kmap/kmap_atomic() with kmap_local_page()
x86: fortify: kmsan: fix KMSAN fortify builds
x86: asm: make sure __put_user_size() evaluates pointer once
Kconfig.debug: disable CONFIG_FRAME_WARN for KMSAN by default
x86/purgatory: disable KMSAN instrumentation
mm: kmsan: export kmsan_copy_page_meta()
mm: migrate: fix return value if all subpages of THPs are migrated successfully
mm/uffd: fix vma check on userfault for wp
mm: prep_compound_tail() clear page->private
mm,madvise,hugetlb: fix unexpected data loss with MADV_DONTNEED on hugetlbfs
mm/page_isolation: fix clang deadcode warning
fs/ext4/super.c: remove unused `deprecated_msg'
ipc/msg.c: fix percpu_counter use after free
memory tier, sysfs: rename attribute "nodes" to "nodelist"
MAINTAINERS: git://github.com -> https://github.com for nilfs2
mm/kmemleak: prevent soft lockup in kmemleak_scan()'s object iteration loops
...
Pull powerpc fixes from Michael Ellerman:
- Fix a case of rescheduling with user access unlocked, when preempt is
enabled.
- A follow-up fix for a recent fix, which could lead to IRQ state
assertions firing incorrectly.
- Two fixes for lockdep warnings seen when using kfence with the Hash
MMU.
- Two fixes for preempt warnings seen when using the Hash MMU.
- Two fixes for the VAS coprocessor mechanism used on pseries.
- Prevent building some of our older KVM backends when
CONTEXT_TRACKING_USER is enabled, as it's known to cause crashes.
- A couple of fixes for issues seen with PMU NMIs.
Thanks to Nicholas Piggin, Guenter Roeck, Frederic Barrat Haren Myneni,
Sachin Sant, and Samuel Holland.
* tag 'powerpc-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s/interrupt: Fix clear of PACA_IRQS_HARD_DIS when returning to soft-masked context
powerpc/64s/interrupt: Perf NMI should not take normal exit path
powerpc/64/interrupt: Prevent NMI PMI causing a dangerous warning
KVM: PPC: BookS PR-KVM and BookE do not support context tracking
powerpc: Fix reschedule bug in KUAP-unlocked user copy
powerpc/64s: Fix hash__change_memory_range preemption warning
powerpc/64s: Disable preemption in hash lazy mmu mode
powerpc/64s: make linear_map_hash_lock a raw spinlock
powerpc/64s: make HPTE lock and native_tlbie_lock irq-safe
powerpc/64s: Add lockdep for HPTE lock
powerpc/pseries: Use lparcfg to reconfig VAS windows for DLPAR CPU
powerpc/pseries/vas: Add VAS IRQ primary handler
Currently the return value of 'sub_driver->init' is not checked. If
sparse_keymap_setup() called in the init function fails, 'generic_
inputdev' is freed, then it will lead a UAF when using it in generic_
acpi_laptop_init(). Fix it by checking the return value and setting
generic_inputdev to NULL after free, so as to avoid double free it.
The error code in generic_subdriver_init() is always negative, so the
return of generic_subdriver_init() can be simplified.
Fixes: 6246ed0911 ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some laptops don't support SW_LID, but still have backlight control,
move backlight resuming before SW_LID event handling so as to avoid
backlight mistake due to early return.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Not all compilers support declare variables in switch-case, so move
declarations to the beginning of a function. Otherwise we may get such
build errors:
arch/loongarch/net/bpf_jit.c: In function ‘emit_atomic’:
arch/loongarch/net/bpf_jit.c:362:3: error: a label can only be part of a statement and a declaration is not a statement
u8 r0 = regmap[BPF_REG_0];
^~
arch/loongarch/net/bpf_jit.c: In function ‘build_insn’:
arch/loongarch/net/bpf_jit.c:727:3: error: a label can only be part of a statement and a declaration is not a statement
u8 t7 = -1;
^~
arch/loongarch/net/bpf_jit.c:778:3: error: a label can only be part of a statement and a declaration is not a statement
int ret;
^~~
arch/loongarch/net/bpf_jit.c:779:3: error: expected expression before ‘u64’
u64 func_addr;
^~~
arch/loongarch/net/bpf_jit.c:780:3: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
bool func_addr_fixed;
^~~~
arch/loongarch/net/bpf_jit.c:784:11: error: ‘func_addr’ undeclared (first use in this function); did you mean ‘in_addr’?
&func_addr, &func_addr_fixed);
^~~~~~~~~
in_addr
arch/loongarch/net/bpf_jit.c:784:11: note: each undeclared identifier is reported only once for each function it appears in
arch/loongarch/net/bpf_jit.c:814:3: error: a label can only be part of a statement and a declaration is not a statement
u64 imm64 = (u64)(insn + 1)->imm << 32 | (u32)insn->imm;
^~~
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Eliminate the following coccicheck warning:
./arch/loongarch/include/asm/ptrace.h:32:15-21: WARNING use flexible-array member instead
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Yushan Zhou <katrinzhou@tencent.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer making sense. Remove the padding for clarity.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Pull s390 fixes from Vasily Gorbik:
- Remove outdated linux390 link from MAINTAINERS
- Add few missing EX_TABLE entries to inline assemblies
- Fix raw data collection for pai_ext PMU
- Add kernel image secure boot trailer for future firmware versions
- Fix out-of-bounds access on cio_ignore free
- Fix memory allocation of mdev_types array in vfio-ap
* tag 's390-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vfio-ap: Fix memory allocation for mdev_types array
s390/cio: fix out-of-bounds access on cio_ignore free
s390/pai: fix raw data collection for PMU pai_ext
s390/boot: add secure boot trailer
s390/pci: add missing EX_TABLE entries to __pcistg_mio_inuser()/__pcilg_mio_inuser()
s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
s390/uaccess: add missing EX_TABLE entries to __clear_user()
MAINTAINERS: remove outdated linux390 link
