ISO 11898-1 specifies in section 11.3.3 "Transmitter delay
compensation" that "the configuration range for [the] SSP position
shall be at least 0 to 63 minimum time quanta."
Because SSP = TDCV + TDCO, it means that we should allow both TDCV and
TDCO to hold zero value in order to honor SSP's minimum possible
value.
However, current implementation assigned special meaning to TDCV and
TDCO's zero values:
* TDCV = 0 -> TDCV is automatically measured by the transceiver.
* TDCO = 0 -> TDC is off.
In order to allow for those values to really be zero and to maintain
current features, we introduce two new flags:
* CAN_CTRLMODE_TDC_AUTO indicates that the controller support
automatic measurement of TDCV.
* CAN_CTRLMODE_TDC_MANUAL indicates that the controller support
manual configuration of TDCV. N.B.: current implementation failed
to provide an option for the driver to indicate that only manual
mode was supported.
TDC is disabled if both CAN_CTRLMODE_TDC_AUTO and
CAN_CTRLMODE_TDC_MANUAL flags are off, c.f. the helper function
can_tdc_is_enabled() which is also introduced in this patch.
Also, this patch adds three fields: tdcv_min, tdco_min and tdcf_min to
struct can_tdc_const. While we are not convinced that those three
fields could be anything else than zero, we can imagine that some
controllers might specify a lower bound on these. Thus, those minimums
are really added "just in case".
Comments of struct can_tdc and can_tdc_const are updated accordingly.
Finally, the changes are applied to the etas_es58x driver.
Link: https://lore.kernel.org/all/20210918095637.20108-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This allows explicitly specifying which children are present on the mdio
bus. Additionally, it allows for non-phy MDIO devices on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an optional mdio bus child node. If present, the mac will
look for PHYs there instead of directly under the top-level node. This
eliminates any ambiguity about whether child nodes are PHYs, and allows
the MDIO bus to contain non-PHY devices.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16nm internal EPHY that is present in 7712 is actually a 16nm
Gigabit PHY which has been forced to operate in 10/100 mode. Its
controls are therefore via the EXT_GPHY_CTRL registers and not via the
EXT_EPHY_CTRL which are used for all GENETv5 adapters. Add a match on
the 7712 compatible string to allow that differentiation to happen.
On previous GENETv4 chips the EXT_CFG_IDDQ_GLOBAL_PWR bit was cleared by
default, but this is not the case with this chip, so we need to make
sure we clear it to power on the EPHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 includes a GENETv5 adapter with an on-chip 10/100 16nm Ethernet PHY
which requires us to document that controller's integration specifically
for proper driver keying.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds some helpers for accessing non-phy MDIO devices. They are
analogous to phy_(read|write|modify), except that they take an mdio_device
and not a phy_device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With current KPU profile, we have 2 reserved entries which can
be loaded from firmware to parse custom headers. Adding changes
to increase these reserved entries to 6.
And also removed KPU entries for unused LTYPEs like
NPC_LT_LA_IH_8_ETHER, NPC_LT_LA_IH_4_ETHER, NPC_LT_LA_IH_2_ETHER
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Delete impossible devlink notifications
This series is a followup to the delayed devlink notification scheme.
I removed the impossible notifications together with attempt to annotate
various calls in order to mark them as pre/post devlink_register().
Other notifications are called before and after delvink_register() so
they weren't changed in this pathcset.
====================
Link: https://lore.kernel.org/r/cover.1634825474.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parameters are registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible parameters
notifications along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The trap logic is registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible trap group
notifications along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The trap policer logic is registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible notifications
along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The change of devlink_register() to be last devlink command together
with delayed notification logic made the publish API to be obsolete.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.
Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following coccicheck warning:
./drivers/net/dsa/sja1105/sja1105_main.c:1193:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Fixes: 9ca482a246 ("net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delays")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211021094606.7118-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Second set of patches for v5.16 and this time we have a big one. We
have the new Realtek driver rtw89 with over 90 kLOC and also over 150
patches for mt76. ath9k also got few new small features. And the usual
cleanups and fixes all over.
Major changes:
rtw89
* new Realtek 802.11ax driver
* supports Realtek 8852AE 802.11ax 2x2 chip
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
mt76
* mt7921 aspm support
* mt7921 testmode support
* mt7915 LED support
* mt7921 6GHz band support
* support for eeprom data in DT
* mt7915 TWT support
* mt7921s SDIO support
* tag 'wireless-drivers-next-2021-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (213 commits)
zd1201: use eth_hw_addr_set()
wl3501_cs: use eth_hw_addr_set()
ray_cs: use eth_hw_addr_set()
...
====================
Link: https://lore.kernel.org/r/20211022075845.0E679C4360D@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Make sure local references to netdev->dev_addr are constant.
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Manually fix all net/usb drivers without separate maintainers.
v2: catc does DMA to the buffer, leave the conversion to Oliver
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Silent merge conflict between these two:
3d677735d3 ("net/mlx5: Lag, move lag files into directory")
14fe2471c6 ("net/mlx5: Lag, change multipath and bonding to be mutually exclusive")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull drm fixes from Dave Airlie:
"Nothing too crazy at the end of the cycle, the kmb modesetting fixes
are probably a bit large but it's not a major driver, and its fixing
monitor doesn't turn on type problems.
Otherwise it's just a few minor patches, one ast regression revert, an
msm power stability fix.
ast:
- fix regression with connector detect
msm:
- fix power stability issue
msxfb:
- fix crash on unload
panel:
- sync fix
kmb:
- modesetting fixes"
* tag 'drm-fixes-2021-10-22' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/ast: Add detect function support"
drm/kmb: Enable ADV bridge after modeset
drm/kmb: Corrected typo in handle_lcd_irq
drm/kmb: Disable change of plane parameters
drm/kmb: Remove clearing DPHY regs
drm/kmb: Limit supported mode to 1080p
drm/kmb: Work around for higher system clock
drm/panel: ilitek-ili9881c: Fix sync for Feixin K101-IM2BYL02 panel
drm: mxsfb: Fix NULL pointer dereference crash on unload
drm/msm/devfreq: Restrict idle clamping to a618 for now
Vladimir Zapolskiy reports:
Commit a7259df767 ("memblock: make memblock_find_in_range method
private") invokes a kernel panic while running kmemleak on OF platforms
with nomaped regions:
Unable to handle kernel paging request at virtual address fff000021e00000
[...]
scan_block+0x64/0x170
scan_gray_list+0xe8/0x17c
kmemleak_scan+0x270/0x514
kmemleak_write+0x34c/0x4ac
The memory allocated from memblock is registered with kmemleak, but if
it is marked MEMBLOCK_NOMAP it won't have linear map entries so an
attempt to scan such areas will fault.
Ideally, memblock_mark_nomap() would inform kmemleak to ignore
MEMBLOCK_NOMAP memory, but it can be called before kmemleak interfaces
operating on physical addresses can use __va() conversion.
Make sure that functions that mark allocated memory as MEMBLOCK_NOMAP
take care of informing kmemleak to ignore such memory.
Link: https://lore.kernel.org/all/8ade5174-b143-d621-8c8e-dc6a1898c6fb@linaro.org
Link: https://lore.kernel.org/all/c30ff0a2-d196-c50d-22f0-bd50696b1205@quicinc.com
Fixes: a7259df767 ("memblock: make memblock_find_in_range method private")
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ucounts fixes from Eric Biederman:
"There has been one very hard to track down bug in the ucount code that
we have been tracking since roughly v5.14 was released. Alex managed
to find a reliable reproducer a few days ago and then I was able to
instrument the code and figure out what the issue was.
It turns out the sigqueue_alloc single atomic operation optimization
did not play nicely with ucounts multiple level rlimits. It turned out
that either sigqueue_alloc or sigqueue_free could be operating on
multiple levels and trigger the conditions for the optimization on
more than one level at the same time.
To deal with that situation I have introduced inc_rlimit_get_ucounts
and dec_rlimit_put_ucounts that just focuses on the optimization and
the rlimit and ucount changes.
While looking into the big bug I found I couple of other little issues
so I am including those fixes here as well.
When I have time I would very much like to dig into process ownership
of the shared signal queue and see if we could pick a single owner for
the entire queue so that all of the rlimits can count to that owner.
That should entirely remove the need to call get_ucounts and
put_ucounts in sigqueue_alloc and sigqueue_free. It is difficult
because Linux unlike POSIX supports setuid that works on a single
thread"
* 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Move get_ucounts from cred_alloc_blank to key_change_session_keyring
ucounts: Proper error handling in set_cred_ucounts
ucounts: Pair inc_rlimit_ucounts with dec_rlimit_ucoutns in commit_creds
ucounts: Fix signal ucount refcounting
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, and can.
We'll have one more fix for a socket accounting regression, it's still
getting polished. Otherwise things look fine.
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv", there are
valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of
init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv abort sessions on
receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg() fix
return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails, prevent
stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues"
* tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
usbnet: sanity check for maxpacket
net: enetc: make sure all traffic classes can send large frames
net: enetc: fix ethtool counter name for PM0_TERR
ptp: free 'vclock_index' in ptp_clock_release()
sfc: Don't use netif_info before net_device setup
sfc: Export fibre-specific supported link modes
net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flags
net/mlx5e: IPsec: Fix a misuse of the software parser's fields
net/mlx5e: Fix vlan data lost during suspend flow
net/mlx5: E-switch, Return correct error code on group creation failure
net/mlx5: Lag, change multipath and bonding to be mutually exclusive
ice: Add missing E810 device ids
igc: Update I226_K device ID
e1000e: Fix packet loss on Tiger Lake and later
e1000e: Separate TGP board type from SPT
ptp: Fix possible memory leak in ptp_clock_register()
net: stmmac: Fix E2E delay mechanism
nfc: st95hf: Make spi remove() callback return zero
net: hns3: disable sriov before unload hclge layer
net: hns3: fix vf reset workqueue cannot exit
...
Pull powerpc fixes from Michael Ellerman:
- Fix a bug exposed by a previous fix, where running guests with
certain SMT topologies could crash the host on Power8.
- Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is
enabled.
Thanks to Nathan Lynch, Srikar Dronamraju, and Valentin Schneider.
* tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/smp: do not decrement idle task preempt count in CPU offline
powerpc/idle: Don't corrupt back chain when going idle
Łukasz Stelmach says:
====================
AX88796C SPI Ethernet Adapter
This is a driver for AX88796C Ethernet Adapter connected in SPI mode as
found on ARTIK5 evaluation board. The driver has been ported from a
v3.10.9 vendor kernel for ARTIK5 board.
====================
Link: https://lore.kernel.org/r/20211020182422.362647-1-l.stelmach@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ASIX AX88796[1] is a versatile ethernet adapter chip, that can be
connected to a CPU with a 8/16-bit bus or with an SPI. This driver
supports SPI connection.
The driver has been ported from the vendor kernel for ARTIK5[2]
boards. Several changes were made to adapt it to the current kernel
which include:
+ updated DT configuration,
+ clock configuration moved to DT,
+ new timer, ethtool and gpio APIs,
+ dev_* instead of pr_* and custom printk() wrappers,
+ removed awkward vendor power managemtn.
+ introduced ethtool tunable to control SPI compression
[1] https://www.asix.com.tw/products.php?op=pItemdetail&PItemID=104;65;86&PLine=65
[2] https://git.tizen.org/cgit/profile/common/platform/kernel/linux-3.10-artik/
The other ax88796 driver is for NE2000 compatible AX88796L chip. These
chips are not compatible. Hence, two separate drivers are required.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code checks whether the skb had one-step TX timestamping enabled, in
order to schedule the work item for emptying the priv->tx_skbs queue.
That code checks for "tx_swbd->skb" directly, when we already had a skb
retrieved using enetc_tx_swbd_get_skb(tx_swbd) - a TX software BD can
also hold an XDP_TX packet or an XDP frame. But since the direct tx_swbd
dereference is in an "if" block guarded by the non-NULL quality of
"skb", accessing "tx_swbd->skb" directly is not wrong, just confusing.
Just use the local variable named "skb".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
