Gal Pressman says:
====================
Fix ntuple rules targeting default RSS
This series addresses a regression in ethtool flow steering where rules
targeting the default RSS context (context 0) were incorrectly rejected.
The default RSS context always exists but is not stored in the rss_ctx
xarray like additional contexts. The current validation logic was
checking for the existence of context 0 in this array, causing valid
flow steering rules to be rejected.
This prevented configurations such as:
- High priority rules directing specific traffic to the default context
- Low priority catch-all rules directing remaining traffic to additional
contexts
Patch 1 fixes the validation logic to skip the existence check for
context 0.
Patch 2 adds a selftest that verifies this behavior.
v3: https://lore.kernel.org/20250609120250.1630125-1-gal@nvidia.com
v2: https://lore.kernel.org/20250225071348.509432-1-gal@nvidia.com
====================
Link: https://patch.msgid.link/20250612071958.1696361-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test_rss_default_context_rule() to verify that ntuple rules can
correctly direct traffic to the default RSS context (context 0).
The test creates two ntuple rules with explicit location priorities:
- A high-priority rule (loc 0) directing specific port traffic to
context 0.
- A low-priority rule (loc 1) directing all other TCP traffic to context
1.
This validates that:
1. Rules targeting the default context function properly.
2. Traffic steering works as expected when mixing default and
additional RSS contexts.
The test was written by AI, and reviewed by humans.
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250612071958.1696361-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Context 0 (default context) always exists, there is no need to check
whether it exists or not when adding a flow steering rule.
The existing check fails when creating a flow steering rule for context
0 as it is not stored in the rss_ctx xarray.
For example:
$ ethtool --config-ntuple eth2 flow-type tcp4 dst-ip 194.237.147.23 dst-port 19983 context 0 loc 618
rmgr: Cannot insert RX class rule: Invalid argument
Cannot insert classification rule
An example usecase for this could be:
- A high-priority rule (loc 0) directing specific port traffic to
context 0.
- A low-priority rule (loc 1) directing all other TCP traffic to context
1.
This is a user-visible regression that was caught in our testing
environment, it was not reported by a user yet.
Fixes: de7f7582df ("net: ethtool: prevent flow steering to RSS contexts which don't exist")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250612071958.1696361-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- eir: Fix NULL pointer deference on eir_get_service_data
- eir: Fix possible crashes on eir_create_adv_data
- hci_sync: Fix broadcast/PA when using an existing instance
- ISO: Fix using BT_SK_PA_SYNC to detect BIS sockets
- ISO: Fix not using bc_sid as advertisement SID
- MGMT: Fix sparse errors
* tag 'for-net-2025-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: MGMT: Fix sparse errors
Bluetooth: ISO: Fix not using bc_sid as advertisement SID
Bluetooth: ISO: Fix using BT_SK_PA_SYNC to detect BIS sockets
Bluetooth: eir: Fix possible crashes on eir_create_adv_data
Bluetooth: hci_sync: Fix broadcast/PA when using an existing instance
Bluetooth: Fix NULL pointer deference on eir_get_service_data
====================
Link: https://patch.msgid.link/20250611204944.1559356-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before the cited commit, the kernel unconditionally embedded SCM
credentials to skb for embryo sockets even when both the sender
and listener disabled SO_PASSCRED and SO_PASSPIDFD.
Now, the credentials are added to skb only when configured by the
sender or the listener.
However, as reported in the link below, it caused a regression for
some programs that assume credentials are included in every skb,
but sometimes not now.
The only problematic scenario would be that a socket starts listening
before setting the option. Then, there will be 2 types of non-small
race window, where a client can send skb without credentials, which
the peer receives as an "invalid" message (and aborts the connection
it seems ?):
Client Server
------ ------
s1.listen() <-- No SO_PASS{CRED,PIDFD}
s2.connect()
s2.send() <-- w/o cred
s1.setsockopt(SO_PASS{CRED,PIDFD})
s2.send() <-- w/ cred
or
Client Server
------ ------
s1.listen() <-- No SO_PASS{CRED,PIDFD}
s2.connect()
s2.send() <-- w/o cred
s3, _ = s1.accept() <-- Inherit cred options
s2.send() <-- w/o cred but not set yet
s3.setsockopt(SO_PASS{CRED,PIDFD})
s2.send() <-- w/ cred
It's unfortunate that buggy programs depend on the behaviour,
but let's restore the previous behaviour.
Fixes: 3f84d577b7 ("af_unix: Inherit sk_flags at connect().")
Reported-by: Jacek Łuczak <difrost.kernel@gmail.com>
Closes: https://lore.kernel.org/all/68d38b0b-1666-4974-85d4-15575789c8d4@gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Tested-by: Christian Heusel <christian@heusel.eu>
Tested-by: André Almeida <andrealmeid@igalia.com>
Tested-by: Jacek Łuczak <difrost.kernel@gmail.com>
Link: https://patch.msgid.link/20250611202758.3075858-1-kuni1840@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdevsim supports netpoll. Make sure we don't call napi_complete()
from it, since it may not be scheduled. Breno reports hitting a
warning in napi_complete_done():
WARNING: CPU: 14 PID: 104 at net/core/dev.c:6592 napi_complete_done+0x2cc/0x560
__napi_poll+0x2d8/0x3a0
handle_softirqs+0x1fe/0x710
This is presumably after netpoll stole the SCHED bit prematurely.
Reported-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Tested-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250611174643.2769263-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
net_sched: no longer use qdisc_tree_flush_backlog()
This series is based on a report from Gerrard Tai.
Essentially, all users of qdisc_tree_flush_backlog() are racy.
We must instead use qdisc_purge_queue().
====================
Link: https://patch.msgid.link/20250611111515.1983366-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerrard Tai reported a race condition in ETS, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes: b05972f01e ("net: sched: tbf: don't call qdisc_put() while holding tree lock")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerrard Tai reported a race condition in TBF, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes: b05972f01e ("net: sched: tbf: don't call qdisc_put() while holding tree lock")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://patch.msgid.link/20250611111515.1983366-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerrard Tai reported a race condition in RED, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes: 0c8d13ac96 ("net: sched: red: delay destroying child qdisc on replace")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerrard Tai reported a race condition in PRIO, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes: 7b8e0b6e65 ("net: sched: prio: delay destroying child qdiscs on change")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerrard Tai reported that SFQ perturb_period has no range check yet,
and this can be used to trigger a race condition fixed in a separate patch.
We want to make sure ctl->perturb_period * HZ will not overflow
and is positive.
Tested:
tc qd add dev lo root sfq perturb -10 # negative value : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb 1000000000 # too big : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb 2000000 # acceptable value
tc -s -d qd sh dev lo
qdisc sfq 8005: root refcnt 2 limit 127p quantum 64Kb depth 127 flows 128 divisor 1024 perturb 2000000sec
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250611083501.1810459-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata.
Cc: stable@vger.kernel.org
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: d219df60a7 ("bpf: Add ipip6 and ip6ip decap support for bpf_skb_adjust_room()")
Fixes: 1b00e0dfe7 ("bpf: update skb->protocol in bpf_skb_net_grow")
Fixes: 6578171a7f ("bpf: add bpf_skb_change_proto helper")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250610001245.1981782-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the link is up, either eth_proto_oper or ext_eth_proto_oper
typically reports the active link protocol, from which both speed
and number of lanes can be retrieved. However, in certain cases,
such as when a NIC is connected via a non-standard cable, the
firmware may not report the protocol.
In such scenarios, the speed can still be obtained from the
data_rate_oper field in PTYS register. Since data_rate_oper
provides only speed information and lacks lane details, it is
incorrect to derive the number of lanes from it.
This patch corrects the behavior by setting the number of lanes to
UNKNOWN instead of incorrectly using MAX_LANES when relying on
data_rate_oper.
Fixes: 7e959797f0 ("net/mlx5e: Enable lanes configuration when auto-negotiation is off")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, a unique tunnel id was added for the matching on TC
non-zero chains, to support inner header rewrite with goto action.
Later, it was used to support VF tunnel offload for vxlan, then for
Geneve and GRE. To support VF tunnel, a temporary mlx5_flow_spec is
used to parse tunnel options. For Geneve, if there is TLV option, a
object is created, or refcnt is added if already exists. But the
temporary mlx5_flow_spec is directly freed after parsing, which causes
the leak because no information regarding the object is saved in
flow's mlx5_flow_spec, which is used to free the object when deleting
the flow.
To fix the leak, call mlx5_geneve_tlv_option_del() before free the
temporary spec if it has TLV object.
Fixes: 521933cdc4 ("net/mlx5e: Support Geneve and GRE with VF tunnel offload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When there are more than one destinations, we create a FW flow
table and provide it with all the destinations. FW requires to
have wire as the last destination in the list (if it exists),
otherwise the operation fails with FW syndrome.
This patch fixes the destination array action creation: if it
contains a wire destination, it is moved to the end.
Fixes: 504e536d90 ("net/mlx5: HWS, added actions handling")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The newly introduced mutex is only used for reformat actions, but it was
initialized for modify header instead.
The struct that contains the mutex is zero-initialized and an all-zero
mutex is valid, so the issue only shows up with CONFIG_DEBUG_MUTEXES.
Fixes: b206d9ec19 ("net/mlx5: HWS, register reformat actions with fw")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When attempting to add a rule to an existing flow group, if a matching
flow group exists but is not active, the error code returned should be
EAGAIN, so that the rule can be added to the matching flow group once
it is active, rather than ENOENT, which indicates that no matching
flow group was found.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When firmware asks the driver to allocate more pages, using event of
give_pages, the driver should always allocate it from same NUMA, the
original device NUMA. Current code uses dev_to_node() which can result
in different NUMA as it is changed by other driver flows, such as
mlx5_dma_zalloc_coherent_node(). Instead, use saved numa node for
allocating firmware pages.
Fixes: 311c7c71c9 ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-06-10 (i40e, iavf, ice, e1000)
For i40e:
Robert Malz improves reset handling for situations where multiple reset
requests could cause some to be missed.
For iavf:
Ahmed adds detection, and handling, of reset that could occur early in
the initialization process to stop long wait/hangs.
For ice:
Anton, properly, sets missed use_nsecs value.
For e1000:
Joe Damato moves cancel_work_sync() call to avoid deadlock.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000: Move cancel_work_sync to avoid deadlock
ice/ptp: fix crosstimestamp reporting
iavf: fix reset_task for early reset event
i40e: retry VFLR handling if there is ongoing VF reset
i40e: return false from i40e_reset_vf if reset is in progress
====================
Link: https://patch.msgid.link/20250610171348.1476574-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently bc_sid is being ignore when acting as Broadcast Source role,
so this fix it by passing the bc_sid and then use it when programming
the PA:
< HCI Command: LE Set Exte.. (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 140.000 msec (0x00e0)
Max advertising interval: 140.000 msec (0x00e0)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x01
Scan request notifications: Disabled (0x00)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT_SK_PA_SYNC is only valid for Broadcast Sinks which means socket used
for Broadcast Sources wouldn't be able to use the likes of getpeername
to read out the sockaddr_iso_bc fields which may have been update (e.g.
bc_sid).
Fixes: 0a766a0aff ("Bluetooth: ISO: Fix getpeername not returning sockaddr_iso_bc fields")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using and existing adv_info instance for broadcast source it
needs to be updated to periodic first before it can be reused, also in
case the existing instance already have data hci_set_adv_instance_data
cannot be used directly since it would overwrite the existing data so
this reappend the original data after the Broadcast ID, if one was
generated.
Example:
bluetoothctl># Add PBP to EA so it can be later referenced as the BIS ID
bluetoothctl> advertise.service 0x1856 0x00 0x00
bluetoothctl> advertise on
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 13
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x09
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
...
bluetoothctl># Attempt to acquire Broadcast Source transport
bluetoothctl>transport.acquire /org/bluez/hci0/pac_bcast0/fd0
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 255
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0e
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID: 11371620 (0xad8464)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Link: https://github.com/bluez/bluez/issues/1117
Fixes: eca0ae4aea ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The len parameter is considered optional so it can be NULL so it cannot
be used for skipping to next entry of EIR_SERVICE_DATA.
Fixes: 8f9ae5b3ae ("Bluetooth: eir: Add helpers for managing service data")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via C45 (clause 45) mdiobus,
there is no verification of parameters passed to the ioctl and
it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before C45 read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 4e4aafcddb ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via mdiobus, there is no verification of
parameters passed to the ioctl and it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 080bb352fa ("net: phy: Maintain MDIO device and bus statistics")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to 802.1AE standard, when ES and SC flags in TCI are zero,
used SCI should be the current active SC_RX. Current code uses the
header MAC address. Without this patch, when ES flag is 0 (using a
bridge or switch), header MAC will not fit the SCI and MACSec frames
will be discarted.
In order to test this issue, MACsec link should be stablished between
two interfaces, setting SC and ES flags to zero and a port identifier
different than one. For example, using ip macsec tools:
ip link add link $ETH0 macsec0 type macsec port 11 send_sci off
end_station off
ip macsec add macsec0 tx sa 0 pn 2 on key 01 $ETH1_KEY
ip macsec add macsec0 rx port 11 address $ETH1_MAC
ip macsec add macsec0 rx port 11 address $ETH1_MAC sa 0 pn 2 on key 02
ip link set dev macsec0 up
ip link add link $ETH1 macsec1 type macsec port 11 send_sci off
end_station off
ip macsec add macsec1 tx sa 0 pn 2 on key 01 $ETH0_KEY
ip macsec add macsec1 rx port 11 address $ETH0_MAC
ip macsec add macsec1 rx port 11 address $ETH0_MAC sa 0 pn 2 on key 02
ip link set dev macsec1 up
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Co-developed-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de>
Signed-off-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de>
Signed-off-by: Carlos Fernandez <carlos.fernandez@technica-engineering.de>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before appending sysdata, prepare_extradata() checks if any feature is
enabled in sysdata_fields (and exits early if none is enabled).
When SYSDATA_RELEASE was introduced, we missed adding it to the list of
features being checked against sysdata_fields in prepare_extradata().
The result was that, if only SYSDATA_RELEASE is enabled in
sysdata_fields, we incorreclty exit early and fail to append the
release.
Instead of checking specific bits in sysdata_fields, check if
sysdata_fields has ALL bit zeroed and exit early if true. This fixes
case when only SYSDATA_RELEASE enabled and makes the code more general /
less error prone in future feature implementation.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Fixes: cfcc9239e7 ("netconsole: append release to sysdata")
Link: https://patch.msgid.link/20250609-netconsole-fix-v1-1-17543611ae31@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk->sk_prot->sock_is_readable is a valid function pointer when sk resides
in a sockmap. After the last sk_psock_put() (which usually happens when
socket is removed from sockmap), sk->sk_prot gets restored and
sk->sk_prot->sock_is_readable becomes NULL.
This makes sk_is_readable() racy, if the value of sk->sk_prot is reloaded
after the initial check. Which in turn may lead to a null pointer
dereference.
Ensure the function pointer does not turn NULL after the check.
Fixes: 8934ce2fd0 ("bpf: sockmap redirect ingress support")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250609-skisreadable-toctou-v1-1-d0dfb2d62c37@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set use_nsecs=true as timestamp is reported in ns. Lack of this result
in smaller timestamp error window which cause error during phc2sys
execution on E825 NICs:
phc2sys[1768.256]: ioctl PTP_SYS_OFFSET_PRECISE: Invalid argument
This problem was introduced in the cited commit which omitted setting
use_nsecs to true when converting the ice driver to use
convert_base_to_cs().
Testing hints (ethX is PF netdev):
phc2sys -s ethX -c CLOCK_REALTIME -O 37 -m
phc2sys[1769.256]: CLOCK_REALTIME phc offset -5 s0 freq -0 delay 0
Fixes: d4bea547eb ("ice/ptp: Remove convert_art_to_tsc()")
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a reset event is received from the PF early in the init cycle, the
state machine hangs for about 25 seconds.
Reproducer:
echo 1 > /sys/class/net/$PF0/device/sriov_numvfs
ip link set dev $PF0 vf 0 mac $NEW_MAC
The log shows:
[792.620416] ice 0000:5e:00.0: Enabling 1 VFs
[792.738812] iavf 0000:5e:01.0: enabling device (0000 -> 0002)
[792.744182] ice 0000:5e:00.0: Enabling 1 VFs with 17 vectors and 16 queues per VF
[792.839964] ice 0000:5e:00.0: Setting MAC 52:54:00:00:00:11 on VF 0. VF driver will be reinitialized
[813.389684] iavf 0000:5e:01.0: Failed to communicate with PF; waiting before retry
[818.635918] iavf 0000:5e:01.0: Hardware came out of reset. Attempting reinit.
[818.766273] iavf 0000:5e:01.0: Multiqueue Enabled: Queue pair count = 16
Fix it by scheduling the reset task and making the reset task capable of
resetting early in the init cycle.
Fixes: ef8693eb90 ("i40evf: refactor reset handling")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VFLR interrupt is received during a VF reset initiated from a
different source, the VFLR may be not fully handled. This can
leave the VF in an undefined state.
To address this, set the I40E_VFLR_EVENT_PENDING bit again during VFLR
handling if the reset is not yet complete. This ensures the driver
will properly complete the VF reset in such scenarios.
Fixes: 52424f974b ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The function i40e_vc_reset_vf attempts, up to 20 times, to handle a
VF reset request, using the return value of i40e_reset_vf as an indicator
of whether the reset was successfully triggered. Currently, i40e_reset_vf
always returns true, which causes new reset requests to be ignored if a
different VF reset is already in progress.
This patch updates the return value of i40e_reset_vf to reflect when
another VF reset is in progress, allowing the caller to properly use
the retry mechanism.
Fixes: 52424f974b ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- MGMT: Fix UAF on mgmt_remove_adv_monitor_complete
- MGMT: Protect mgmt_pending list with its own lock
- hci_core: fix list_for_each_entry_rcu usage
- btintel_pcie: Increase the tx and rx descriptor count
- btintel_pcie: Reduce driver buffer posting to prevent race condition
- btintel_pcie: Fix driver not posting maximum rx buffers
* tag 'for-net-2025-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: MGMT: Protect mgmt_pending list with its own lock
Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete
Bluetooth: btintel_pcie: Reduce driver buffer posting to prevent race condition
Bluetooth: btintel_pcie: Increase the tx and rx descriptor count
Bluetooth: btintel_pcie: Fix driver not posting maximum rx buffers
Bluetooth: hci_core: fix list_for_each_entry_rcu usage
====================
Link: https://patch.msgid.link/20250605191136.904411-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SFQ has an assumption of always being able to queue at least one packet.
However, after the blamed commit, sch->q.len can be inflated by packets
in sch->gso_skb, and an enqueue() on an empty SFQ qdisc can be followed
by an immediate drop.
Fix sfq_drop() to properly clear q->tail in this situation.
Tested:
ip netns add lb
ip link add dev to-lb type veth peer name in-lb netns lb
ethtool -K to-lb tso off # force qdisc to requeue gso_skb
ip netns exec lb ethtool -K in-lb gro on # enable NAPI
ip link set dev to-lb up
ip -netns lb link set dev in-lb up
ip addr add dev to-lb 192.168.20.1/24
ip -netns lb addr add dev in-lb 192.168.20.2/24
tc qdisc replace dev to-lb root sfq limit 100
ip netns exec lb netserver
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
Fixes: a53851e2c3 ("net: sched: explicit locking in gso_cpu fallback")
Reported-by: Marcus Wichelmann <marcus.wichelmann@hetzner-cloud.de>
Closes: https://lore.kernel.org/netdev/9da42688-bfaa-4364-8797-e9271f3bdaef@hetzner-cloud.de/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20250606165127.3629486-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
