RSSI statistics are grouped by CCK, OFDM or non-legacy rate. These
statistics will be collected in training state for both (main/aux)
antenna. There is a time period (ANTDIV_DELAY) for rate adaptive
settle down before start collect statistics when switch antenna.
Antenna diversity checks packet count from training state for each
group and use the most one as the final RSSI for comparison, and
then choose the better one as target antenna.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-7-pkshih@realtek.com
RSSI strength is only from PHY path A, but there are two antenna for the
module which supports antenna diversity. So, set RSSI value to index 1 of
RSSI array if current antenna is on antenna B. Then, debugfs can show
two RSSI values with a asterisk mark on selected antenna.
RSSI: -23 dBm (raw=174, prev=173) [-26, -23*]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-4-pkshih@realtek.com
TX antenna diversity is a mechanism to select a proper antenna from two
antenna for single one hardware PHY chip. It chooses antenna with better
EVM or RSSI, and use GPIO to control SPDT to switch selected antenna.
RFE type from efuse is used to define if a module can support TX antenna
diversity when (type % 3) is 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-3-pkshih@realtek.com
If there is a failure during copy_from_user or user-provided data
buffer is invalid, rtw_debugfs_copy_from_user should return negative
error code instead of a positive value count.
Fix this bug by returning correct error code. Moreover, the check
of buffer against null is removed since it will be handled by
copy_from_user.
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/tencent_D2EB102CC7435C0110154E62ECA6A7D67505@qq.com
The driver can receive several frames in the same USB transfer.
Add the code to handle this in rtl8xxxu_parse_rxdesc24(), even though
currently all the relevant chips send only one frame per USB transfer
(RTL8723BU, RTL8192EU, RTL8188FU, RTL8710BU).
This was tested with RTL8188FU, RTL8192EU, RTL8710BU, and RTL8192FU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/16d2d1ff-6438-10c9-347f-6e14dd358ccf@gmail.com
As this driver uses HAS_RATE_CONTROL, rate_flags will not be provided by
mac80211.
Stop using tx_info->control.rates[0].flags and ieee80211_get_rts_cts_rate()
and use rts_threshold and bss_conf.use_cts_prot instead to determine
when to use RTS and CTS.
Send RTS with 24M rate like the vendor drivers. Also set this RTS rate
for ampdu_enable = true, because we also enable RTS for these frames.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230428150833.218605-17-martin.kaistra@linutronix.de
As this driver uses HAS_RATE_CONTROL, tx_rates will not be provided by
mac80211.
For some frames c->control.rates[0].idx is negative, which means
ieee80211_get_tx_rate() will print a warning and return NULL.
Only management frames have USE_DRIVER_RATE set, so for all others the
rate info of txdesc is ignored anyway.
Remove call to ieee80211_get_tx_rate() and send management frames with
1M (rate info = 0).
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230428150833.218605-16-martin.kaistra@linutronix.de
When the action of an xdp program was XDP_TX, lan966x was creating
a xdp_frame and use this one to send the frame back. But it is also
possible to send back the frame without needing a xdp_frame, because
it is possible to send it back using the page.
And then once the frame is transmitted is possible to use directly
page_pool_recycle_direct as lan966x is using page pools.
This would save some CPU usage on this path, which results in higher
number of transmitted frames. Bellow are the statistics:
Frame size: Improvement:
64 ~8%
256 ~11%
512 ~8%
1000 ~0%
1500 ~0%
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230422142344.3630602-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-04-24
We've added 5 non-merge commits during the last 3 day(s) which contain
a total of 7 files changed, 87 insertions(+), 44 deletions(-).
The main changes are:
1) Workaround for bpf iter selftest due to lack of subprog support
in precision tracking, from Andrii.
2) Disable bpf_refcount_acquire kfunc until races are fixed, from Dave.
3) One more test_verifier test converted from asm macro to asm in C,
from Eduard.
4) Fix build with NETFILTER=y INET=n config, from Florian.
5) Add __rcu_read_{lock,unlock} into deny list, from Yafang.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
selftests/bpf: avoid mark_all_scalars_precise() trigger in one of iter tests
bpf: Add __rcu_read_{lock,unlock} into btf id deny list
bpf: Disable bpf_refcount_acquire kfunc calls until race conditions are fixed
selftests/bpf: verifier/prevent_map_lookup converted to inline assembly
bpf: fix link failure with NETFILTER=y INET=n
====================
Link: https://lore.kernel.org/r/20230425005648.86714-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gerhard Engleder says:
====================
tsnep: XDP socket zero-copy support
Implement XDP socket zero-copy support for tsnep driver. I tried to
follow existing drivers like igc as far as possible. But one main
difference is that tsnep does not need any reconfiguration for XDP BPF
program setup. So I decided to keep this behavior no matter if a XSK
pool is used or not. As a result, tsnep starts using the XSK pool even
if no XDP BPF program is available.
Another difference is that I tried to prevent potentially failing
allocations during XSK pool setup. E.g. both memory models for page pool
and XSK pool are registered all the time. Thus, XSK pool setup cannot
end up with not working queues.
Some prework is done to reduce the last two XSK commits to actual XSK
changes.
====================
Link: https://lore.kernel.org/r/20230421194656.48063-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Send and complete XSK pool frames within TX NAPI context. NAPI context
is triggered by ndo_xsk_wakeup.
Test results with A53 1.2GHz:
xdpsock txonly copy mode, 64 byte frames:
pps pkts 1.00
tx 284,409 11,398,144
Two CPUs with 100% and 10% utilization.
xdpsock txonly zero-copy mode, 64 byte frames:
pps pkts 1.00
tx 511,929 5,890,368
Two CPUs with 100% and 1% utilization.
xdpsock l2fwd copy mode, 64 byte frames:
pps pkts 1.00
rx 248,985 7,315,885
tx 248,921 7,315,885
Two CPUs with 100% and 10% utilization.
xdpsock l2fwd zero-copy mode, 64 byte frames:
pps pkts 1.00
rx 254,735 3,039,456
tx 254,735 3,039,456
Two CPUs with 100% and 4% utilization.
Packet rate increases and CPU utilization is reduced in both cases.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for XSK zero-copy to RX path. The setup of the XSK pool can
be done at runtime. If the netdev is running, then the queue must be
disabled and enabled during reconfiguration. This can be done easily
with functions introduced in previous commits.
A more important property is that, if the netdev is running, then the
setup of the XSK pool shall not stop the netdev in case of errors. A
broken netdev after a failed XSK pool setup is bad behavior. Therefore,
the allocation and setup of resources during XSK pool setup is done only
before any queue is disabled. Additionally, freeing and later allocation
of resources is eliminated in some cases. Page pool entries are kept for
later use. Two memory models are registered in parallel. As a result,
the XSK pool setup cannot fail during queue reconfiguration.
In contrast to other drivers, XSK pool setup and XDP BPF program setup
are separate actions. XSK pool setup can be done without any XDP BPF
program. The XDP BPF program can be added, removed or changed without
any reconfiguration of the XSK pool.
Test results with A53 1.2GHz:
xdpsock rxdrop copy mode, 64 byte frames:
pps pkts 1.00
rx 856,054 10,625,775
Two CPUs with both 100% utilization.
xdpsock rxdrop zero-copy mode, 64 byte frames:
pps pkts 1.00
rx 889,388 4,615,284
Two CPUs with 100% and 20% utilization.
Packet rate increases and CPU utilization is reduced.
100% CPU load seems to the base load. This load is consumed by ksoftirqd
just for dropping the generated packets without xdpsock running.
Using batch API reduced CPU utilization slightly, but measurements are
not stable enough to provide meaningful numbers.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function tsnep_rx_poll() is already pretty long and the skb receive
action can be reused for XSK zero-copy support. Move page based skb
receive to separate function.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move queue enable and disable code to separate functions. This way the
activation and deactivation of the queues are defined actions, which can
be used in future execution paths.
This functions will be used for the queue reconfiguration at runtime,
which is necessary for XSK zero-copy support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make initialization of TX and RX queues less dynamic by moving some
initialization from netdev open/close to device probing.
Additionally, move some initialization code to separate functions to
enable future use in other execution paths.
This is done as preparation for queue reconfigure at runtime, which is
necessary for XSK zero-copy support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TX/RX ring size is static and power of 2 to enable compiler to optimize
modulo operation to mask operation. Make this optimization already in
the code and don't rely on the compiler.
CPU utilisation during high packet rate has not changed. So no
performance improvement has been measured. But it is best practice to
prevent modulo operations.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SET_COALESCE may change operation mode and parameters in one call.
Changing operation mode may cause the driver to reset the parameter
values to what is a reasonable default for new operation mode.
Since driver does not know which parameters come from user and which
are echoed back from ->get, driver may ignore the parameters when
switching operation modes.
This used to be inevitable for ioctl() but in netlink we know which
parameters are actually specified by the user.
We could inform which parameters were set by the user but this would
lead to a lot of code duplication in the drivers. Instead try to call
the drivers twice if both mode and params are changed. The set method
already checks if any params need updating so in case the driver did
the right thing the first time around - there will be no second call
to it's ->set method (only an extra call to ->get()).
For mlx5 for example before this patch we'd see:
# ethtool -C eth0 adaptive-rx on adaptive-tx on
# ethtool -C eth0 adaptive-rx off adaptive-tx off \
tx-usecs 123 rx-usecs 123
Adaptive RX: off TX: off
rx-usecs: 3
rx-frames: 32
tx-usecs: 16
tx-frames: 32
[...]
After the change:
# ethtool -C eth0 adaptive-rx on adaptive-tx on
# ethtool -C eth0 adaptive-rx off adaptive-tx off \
tx-usecs 123 rx-usecs 123
Adaptive RX: off TX: off
rx-usecs: 123
rx-frames: 32
tx-usecs: 123
tx-frames: 32
[...]
This only works for netlink, so it's a small discrepancy between
netlink and ioctl(). Since we anticipate most users to move to
netlink I believe it's worth making their lives easier.
Link: https://lore.kernel.org/r/20230420233302.944382-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Haiyang Zhang says:
====================
Update coding style and check alloc_frag
Follow up patches for the jumbo frame support.
As suggested by Jakub Kicinski, update coding style, and check napi_alloc_frag
for possible fallback to single pages.
====================
Link: https://lore.kernel.org/r/1682096818-30056-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev/napi_alloc_frag() may fall back to single page which is smaller
than the requested size.
Add error checking to avoid memory overwritten.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename mana_refill_rxoob for naming consistency.
And remove some empty lines between function call and error
checking.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lorenzo Bianconi says:
====================
add page_pool support for page recycling in veth driver
Introduce page_pool support in veth driver in order to recycle pages in
veth_convert_skb_to_xdp_buff routine and avoid reallocating the skb through
the page allocator when we run a xdp program on the device and we receive
skbs from the stack.
====================
Link: https://lore.kernel.org/r/cover.1682188837.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce page_pool stats support to report info about local page_pool
through ethtool
Tested-by: Maryam Tahhan <mtahhan@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
