Move the possible resolution values back to the driver. This removes the
atmel,adc-res and atmel,adc-res-names properties, leaving only
atmel,adc-use-res. As atmel,adc-res-names had to contain "lowres" and
"highres", those where already the only allowed values for
atmel,adc-use-res.
Also introduce a new compatible string for the sama5d3 as this is the only
one with a different resolution. Also it doesn't even have the LOWRES
bit.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-3-alexandre.belloni@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We use this part in an example for the envelope detector. That showed
that we need to allow for the #io-channel-cells property which
trivial-devices.yaml does not.
It doesn't make sense to add that property to trivial-devices as
it only applies for those devices that can provide some sort of
DAC or ADC service to another device driver. Hence solution will
be to pull some IIO devices out to have their own file on a case
by case basis.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20201031181242.742301-4-jic23@kernel.org
This basically has same questions as for the afe4403. We could combine
the two bindings, but as the drivers are separate and it would be a little
fiddly due to different buses let's keep the separating.
To repeat questions from the ti,afe4403 binding.
A few questions came up whilst converting this one.
1) What is actually required?
- Checking Linux driver, interrupt is not, and the tx-supply could
be supplied by a stub regulator as long as it's always on.
As such I have reduced the required list to just compatible and reg.
2) What is the regulator called?
- It's tx-supply in the binding doc, but the driver request tx_sup
I will shortly send out a fix for the driver to match the binding
doc which is the better choice of naming.
As Andrew's email is bouncing, I've put myself as temporary maintainer
for this binding until someone else steps up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201031184854.745828-9-jic23@kernel.org
A few questions came up whilst converting this one.
1) What is actually required?
- Checking Linux driver, interrupt is not, and the tx-supply could
be supplied by a stub regulator as long as it's always on.
As such I have reduced the required list to just compatible and reg.
2) What is the regulator called?
- It's tx-supply in the binding doc, but the driver requests tx_sup.
I'll post a fix patch to change the driver to fix this as it makes
little sense.
Andrew's email is bouncing so until someone else steps up I have
listed myself as maintainer for this binding.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201031184854.745828-8-jic23@kernel.org
When updating the buffer demux, we will skip a scan element from the
device in the case `in_ind != out_ind` and we enter the while loop.
in_ind should only be refreshed with `find_next_bit()` in the end of the
loop.
Note, to cause problems we need a situation where we are skippig over
an element (channel not enabled) that happens to not have the same size
as the next element. Whilst this is a possible situation we haven't
actually identified any cases in mainline where it happens as most drivers
have consistent channel storage sizes with the exception of the timestamp
which is the last element and hence never skipped over.
Fixes: 5ada4ea9be ("staging:iio: add demux optionally to path from device to buffer")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20201112144323.28887-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_format_avail_list() and iio_format_avail_range() functions are
almost identical. The only differences are that iio_format_avail_range()
expects a fixed amount of items and adds brackets "[ ]" around the output.
Refactor them into a common helper function. This improves the
maintainability of the code as it makes it easier to modify the
implementation of these functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20201114120000.6533-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a heap allocated memory for the SPI transfer buffer. Using stack memory
can corrupt stack memory when using DMA on some systems.
This change moves the buffer from the stack of the trigger handler call to
the heap of the buffer of the state struct. The size increases takes into
account the alignment for the timestamp, which is 8 bytes.
The 'data' buffer is split into 'tx_buf' and 'rx_buf', to make a clearer
separation of which part of the buffer should be used for TX & RX.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201124123807.19717-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
register functions, and a devm_add_action_or_reset() for the regulator
disable.
With this, the exit & error paths can be removed.
Another side-effect is that this should avoid some static-analyzer's check
with respect to a potential null dereference of the regulator. The null
dereference isn't likely to happen (under normal operation), so there isn't
a requirement to have this fixed/backported in other releases.
As a note: this is removing spi_set_drvdata() since there is no other
spi_get_drvdata() (or dev_get_drvdata()) call that need it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201127094038.91714-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
So far, the thermocouple-type property described in here is only
used in a single driver. Whilst I would like it to be more generally
used that hasn't happened yet and I don't see a reason to maintain
this small file in the hope that it happens.
I pushed for this generic binding in the first place. Hopefully
we can bring it back at somepoint.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Link: https://lore.kernel.org/r/20201031184854.745828-47-jic23@kernel.org
This binding document covers a very large number of different sensors.
As such the existing documentation is less specific than it could
be (such as which devices have 2 interrupt pin options).
That can be improved later.
Denis, are you happy to be listed as maintainer for this one?
If not feel free to suggestion someone else.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Link: https://lore.kernel.org/r/20201031184854.745828-45-jic23@kernel.org
One question in here is whether we want to constrain the number of
interrupts. Some parts definitely only have 1 such pin, and others
2 pins but I can not find information on the bma254.
Oleksandr's email address is bouncing so I've listed myself as
maintainer for this binding until someone else steps up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201031184854.745828-41-jic23@kernel.org
The current driver and indeed binding are named after a part that they
do not list in the compatible. Hence renamed the binding to reflect
one that does.
>From the driver it looks like there is a lot more backwards compatibility
than the binding currently reflects. We could consider expressing that
more explicitly in the yaml for the compatible property. I have
added one explicit pair that was present in the upstream dtsi files.
I added Matthias alongside Zhiyong Tao because I don't think
Zhiyong Tao has reviewed recent patches. Please let me know if this
isn't the right thing to do.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20201031184854.745828-34-jic23@kernel.org
A few questions came up in this one.
1) Why does the txt file document io-channel-ranges as a required property.
That property is for iio-channel consumers, and this is a provider.
I have dropped it.
2) The example had an @180a6000 for the ADC but given it uses syscon for
all access, it doesn't have its own reg etc. I've dropped that from
the binding example.
Note this example was lifted directly from bcm-cygnus.dtsi so both
issues are present there as well.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Link: https://lore.kernel.org/r/20201031184854.745828-33-jic23@kernel.org
