arm64: ZynqMP DT changes for v6.5
Various small fixes and cleanups to be aligned with the latest dt-schema.
Other major changes are:
- Wire mali-400 gpu
- Change board name for zcu1275
- Use ethernet-phy-id to handle ETH phy reset properly
- Switch to amd.com emails
- Update people in DT bindings
* tag 'zynqmp-dt-for-v6.5' of https://github.com/Xilinx/linux-xlnx: (33 commits)
dt-bindings: usb: xilinx: Replace Manish by Piyush
dt-bindings: xilinx: Remove Rajan, Jolly and Manish
arm64: zynqmp: Used fixed-partitions for QSPI in k26
arm64: zynqmp: Add pmu interrupt-affinity
arm64: zynqmp: Set qspi tx-buswidth to 4
arm64: zynqmp: Fix usb node drive strength and slew rate
arm64: zynqmp: Describe TI phy as ethernet-phy-id
arm64: zynqmp: Switch to amd.com emails
arm64: zynqmp: Convert kv260-revA overlay to ASCII text
dt-bindings: xilinx: Switch xilinx.com emails to amd.com
arm64: xilinx: Use zynqmp prefix for SOM dt overlays
arm64: zynqmp: Add phase tags marking
arm64: zynqmp: Describe bus-width for SD card on KV260
arm64: zynqmp: Enable AMS on SOM and other zcu10x boards
arm64: zynqmp: Enable DP driver for SOMs
arm64: zynqmp: Setup clock for DP and DPDMA
arm64: zynqmp: Switch to ethernet-phy-id in kv260
arm64: zynqmp: Disable USB3.0 for zc1751-xm016-dc2
arm64: zynqmp: Add pinctrl emmc description to SM-K26
arm64: zynqmp: Add gpio labels for modepin gpio
...
Link: https://lore.kernel.org/r/CAHTX3d+2s_KmCnd=x5hydGb+LYoznAzYGTizvqqN2NFmrBurfw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New boards are
- Indiedroid Nova (rk3588)
- Add Edgeble Neural Compute Module 6B (rk3588)
- FriendlyARM NanoPi R2C Plus (rk3328)
- Anbernic RG353PS (rk3566)
- Lunzn Fastrhino R66S / R68S (rk3568)
The rk3588 got a lot of attention and gained support for the GIC ITS
(needed an errata from Rockchip), timers, otp memory, saradc and sdio.
The rk356x got support for its RGA block
With all the core improvements to rk3588 support, the Rock5b got a lot
improvements from that too, namely support for its PMIC, sd-card and
saradc, as well as a clock-rate fix for its es8316 codec.
Similarly the rk3588-evb1 also got support for its PMIC.
The Anberic RGxx3 series got a better bluetooth compatible and updates
to its LEDs to make them use the PWM blocks they're connected to.
* tag 'v6.5-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: Add saradc node to rock5b
arm64: dts: rockchip: Fix compatible for Bluetooth on rk3566-anbernic
arm64: dts: rockchip: Add SD card support to rock-5b
arm64: dts: rockchip: add PMIC to rock-5b
arm64: dts: rockchip: Assign ES8316 MCLK rate on rk3588-rock-5b
arm64: dts: rockchip: Add Indiedroid Nova board
dt-bindings: arm: rockchip: Add Indiedroid Nova
dt-bindings: vendor-prefixes: add Indiedroid
arm64: dts: rockchip: Add sdio node to rk3588
arm64: dts: rockchip: add default pinctrl for rk3588 emmc
arm64: dts: rockchip: Add DT node for ADC support in RK3588
arm64: dts: rockchip: add PMIC to rk3588-evb1
arm64: dts: rockchip: Add rk3588 Edgeble Neu6 Model B IO
arm64: dts: rockchip: Add rk3588 Edgeble Neu6 Model B SoM
arm64: dts: rockchip: Add Rockchip RK3588J
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 6B
arm64: dts: rockchip: Add RGA2 support to rk356x
media: dt-bindings: media: rockchip-rga: add rockchip,rk3568-rga
arm64: dts: rockchip: Add rk3588 OTP node
arm64: dts: rockchip: Add FriendlyARM NanoPi R2C Plus
...
Link: https://lore.kernel.org/r/3239799.44csPzL39Z@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM32 DeviceTree updates for v6.5
NAND support on IPQ4019 boards is restored, after a faulty node rename.
On MSM8226 IMEM, PMU and RPM stats are introduced. The Huawei Watch
gains vibrator support.
On MSM8974, the LGE Nexus 5 gains vibrator support. The APQ8074
Dragonboard marks BLSP2 BAM controlled remotely, DSI panel, audio and
modem DSPs are enabled.
On SDX65 PCIe controller and PHY are introduced, to provide endpoint
functionality. This is enabled on the related MTP.
A range of DeviceTree cleanups are also included.
* tag 'qcom-dts-for-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (27 commits)
ARM: dts: qcom: apq8074-dragonboard: enable DSI panel
ARM: dts: qcom: apq8074-dragonboard: enable adsp and MSS
ARM: dts: qcom: apq8074-dragonboard: Set DMA as remotely controlled
ARM: dts: qcom: apq8026-huawei-sturgeon: Add vibrator
ARM: dts: qcom: msm8226: Add IMEM node
ARM: dts: qcom: msm8226: Add rpm-stats device node
ARM: dts: qcom: msm8226: Add PMU node
ARM: dts: qcom: sdx65-mtp: Enable PCIe EP
ARM: dts: qcom: sdx65-mtp: Enable PCIe PHY
ARM: dts: qcom: sdx65: Add support for PCIe EP
ARM: dts: qcom: sdx65: Add support for PCIe PHY
ARM: dts: qcom: msm8974: align WCNSS Bluetooth node name with bindings
ARM: dts: qcom: apq8084: correct thermal sensor unit-address
ARM: dts: qcom: msm8960-cdp: move regulator out of simple-bus
ARM: dts: qcom: apq8060-dragonboard: move regulators out of simple-bus
ARM: dts: qcom: ipq8064: align USB node names with bindings
ARM: dts: qcom: ipq8064: correct LED node names
ARM: dts: qcom: ipq8064: drop invalid GCC thermal-sensor unit-address
ARM: dts: qcom: ipq8064: drop leading 0 from unit-address
ARM: dts: qcom: msm8974: correct pronto unit-address
...
Link: https://lore.kernel.org/r/20230611010843.2482142-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DeviceTree updates for v6.5
This introduces the RDP442 and RDP433 reference devices on IPQ5332 and
IPQ9574, respectively. RDP418, RDP433, RDP449 and RDP453 on the IPQ9574
are added. On MSM8939 the Square T2 board and the Sony Xperia M4 Aqua is
added. Support for Acer Apire 1, built on the Snapdragon 7c platform is
introduced. Fxtec Pro1X on SM6115 is added. Lastly long floating
support for SC8180X and the Lenovo Flex 5G, and the Primus reference
device, has been added.
On IPQ5332 and IPQ6018 QFPROM support is introduced, and as described
above the RDP442 board on the prior. Download mode support and various
reserved-memory regions are also introduced on IPQ6018.
IPQ8074 gains another SPI controller.
On IPQ9574 CPU frequency scaling, low speed busses, RNG, Watchdog,
qfprom, SMEM and RPM are introduced. As are support for four new board,
mentioned above.
MSM8916 gains a range of structural improvements, to better suite the
various boards supported. Regulator constraints are corrected and their
states are adjusted to match reality (e.g. always-on regulators marked
as always-on). BQ Aquaris X5 gains support for front flash LED.
As mentioned above, MSM8939 support is introduced with support for
boards from Sony and Square.
MSM8953 gains DMA support in I2C masters.
MSM8996-based Sony Xperia boards gains description of their RGB
notification LED.
On SA8775P support for UFS, USB, GPU clock and iommu controllers, PMU,
AOSS, watchdog and missing low-speed controllers are added. On the Ride
platform UFS, USB and an i2c bus are enabled.
iommu properties are added to QSPI on both SC7180 and SC7280. LPASS
clocks are adjusted and MDP node cleaned up slightly, on SC7180. As
mentioned above, support for Acer Aspire 1 is introduced.
Long lingering patches introducing SC8180X, the Lenovo Flex 5G and the
Primus reference device has been merged.
On SC8280XP ethernet is added and enabled on the automotive ride
platform. An SDC controller is introduced and enabled on the SC8280XP
CRD. On the Lenovo Thinkpad X13s and the CRD reference device the USB
SuperSpeed phy is added to the Type-C graph, to enable support for
orientation switching.
Fairphone 3 gains support for its notification LED.
On SDM845 the iommu stream for QSPI is defined, SHIFT SHIFT6mq gains
support for flash LED and the RB3 (DB845c) board gains support for
bonded/dual DSI-mode, to allow 4k output.
On SM6115 CPU idle-states, crypto engine support and SuperSpeed USB PHY
are introduced. As mentioned above Fxtec Pro1X is introduced. On the
QRB4210 Robotics Platform RB2 USB, Audio and Compute DSPs, display,
CAN-bus and GPIO LEDs are introduced, fixed regulators are described and
the SD-card description is corrected.
Support for crypto engine is added to SM8150, while Sony Xperia 1 and 5
gains SD-card support, camera regulators and GPIO line names sorted out.
SM8250 also gets support for crypto engine, and Sony Xperia 1 II and 5
II gains support for hardware video accelerator.
Crypto engine is introduced for SM8350 as well. The HDK gets the USB
Type-C graph described for Superspeed orientation switching and
DisplayPort output.
On SM8450 video clock controller and crypto engine are added, missing
opp levels are introduced and the USB Type-C graph is defined for
orientation switching and altmode.
SM8550 gains GPU and video clock controllers and missing opp levels are
added. The WCD9385 audio codec is added for the SM8550 MTP and on the
QRD PCIe, USB, audio display and flash LED are added.
* tag 'qcom-arm64-for-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (195 commits)
arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G
arm64: dts: qcom: sc8180x: Introduce Primus
arm64: dts: qcom: sc8180x: Add pmics
arm64: dts: qcom: sc8180x: Add display and gpu nodes
arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes
arm64: dts: qcom: sc8180x: Add PCIe instances
arm64: dts: qcom: sc8180x: Add QUPs
arm64: dts: qcom: sc8180x: Add thermal zones
arm64: dts: qcom: sc8180x: Add interconnects and lmh
arm64: dts: qcom: Introduce the SC8180x platform
arm64: dts: qcom: msm8916: Move aliases to boards
arm64: dts: qcom: pm8916: Rename &wcd_codec -> &pm8916_codec
arm64: dts: qcom: msm8916/39: Clean up MDSS labels
arm64: dts: qcom: msm8916/39: Use consistent name for I2C/SPI pinctrl
arm64: dts: qcom: msm8916/39: Rename &blsp1_uartN -> &blsp_uartN
arm64: dts: qcom: msm8916: Rename &msmgpio -> &tlmm
arm64: dts: qcom: qrb4210-rb2: Enable USB node
arm64: dts: qcom: sm6115: Add USB SS qmp phy node
arm64: dts: qcom: ipq5332: add support for the RDP442 variant
dt-bindings: arm: qcom: document MI01.3 board based on IPQ5332 family
...
Link: https://lore.kernel.org/r/20230611004944.2481596-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree for 6.5:
- New board support: i.MX8MM based Emtop SoM & Baseboard, NXP i.MX8MM EVKB
board, i.MX8MP based Gateworks Venice gw7905-2x device.
- A series from Adam Ford to add Camera and Audio support for i.MX8M
based Beacon boards.
- Add Audio output support for i.MX8MP TQMa8MPxL/MBa8MPxL board.
- Add HDMI and display support for imx8mm-evk and imx8mm-phg board.
- Add coresight trace devices support for i.MX8MP SoC.
- A couple of changes from Krzysztof Kozlowski to add missing cache
properties.
- A couple of changes from Laurent Pinchart to add CSIS and ISI devices
for i.MX8MP SoC.
- A series from Marek Vasut to add more devices for i.MX8MP, and enable
SAI audio on i.MX8MP DHCOM PDK2 and PDK3.
- Correct GSC vdd_bat data size for Gateworks Venice devices.
- Add more device support for i.MX93, Watchdog, OCOTP, idle states, DDR
performance monitor, etc.
- Small and random clean-ups and device node additions.
* tag 'imx-dt64-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
arm64: dts: imx8mq: Pass address-cells/size-cells to mipi_dsi
arm64: dts: imx8mq: Use 'dsi' as node name
arm64: dts: imx8mp-venice-gw702x: fix GSC vdd_bat data size
arm64: dts: imx8mq-tqma8mq-mba8mx: Remove invalid properties
arm64: dts: imx8mq: Add missing pci property
arm64: dts: imx8mq: Fix lcdif clocks
arm64: dts: imx8mq: Fix lcdif compatible
arm64: dts: imx8mp: don't initialize audio clocks from CCM node
arm64: dts: imx8mm-venice: Fix GSC vdd_bat data size.
arm64: dts: imx8mp: Add coresight trace components
arm64: dts: imx93: add ddr performance monitor node
arm64: dts: imx8mm-phg: Add display support
arm64: dts: tqma8mqml: Add vcc supply to i2c eeproms
arm64: dts: imx8mm-evk: Add HDMI support
arm64: dts: imx8mn-var-som-symphony: adapt FEC pinctrl for SOMs with onboard PHY
arm64: dts: imx8mn-var-som: add 20ms delay to ethernet regulator enable
arm64: dts: imx8mp-msc-sm2s: Add sound card
arm64: dts: imx8mn-beacon: Migrate sound card to simple-audio-card
arm64: dts: imx8mp-beacon-kit: Enable WM8962 Audio CODEC
arm64: dts: imx93: add fsl,stop-mode property to support WOL
...
Link: https://lore.kernel.org/r/20230610072530.418847-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX ARM device tree for 6.5:
- New board support: Marantec Maveo Box.
- Add HDMI support for TQMa6x/MBa6 board.
- A series from Andrew Lunn to add phy-mode and fixed links for Ethernet
devices on imx51, imx6qdl and vf610.
- A bunch of changes from Fabio Estevam to clean up deprecated and
invalid properies, fix up node names to remove dt-schema warnings.
- A series of maintenance updates for Protonic Holland boards, mostly
on the USB subsystem configuration, thermal zones, and the naming of
GPIO keys.
- Update dma-apbh device node name to remove dtbs_check warnings.
- Remove invalid nodes from fan-controller for a couple of Gateworks
boards.
- Small random updates and clean-ups on various boards.
* tag 'imx-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: imx6qdl: vicut1: rename power to power-button
ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
ARM: dts: imx6dl: plybas: fix USB over-current detection on USB OTG port
ARM: dts: imx6ul: prti6g: fix USB over-current detection on USB OTG port
ARM: dts: imx6qp: prtwd3: Enable USB over current detection on USB OTG port
ARM: dts: imx6dl: prtmvt: fix different USB related warnings
ARM: dts: imx6dl: alti6p: fix different USB related warnings
ARM: dts: imx6dl: vicut1: Address USB related warnings
ARM: dts: imx6dl: Add trip points to thermal zones on several devices
ARM: dts: imx6dl: lanmcu: Configure over-current polarity for USB OTG node
ARM: dts: imx6dl: lanmcu: Disable unused USB PHY nodes
ARM: dts: imx6q: prtwd2: Correct iomux configuration for ENET MDIO and MDC
ARM: dts: imx6dl: prtvt7: Remove touchscreen inversion
ARM: dts: imx6dl: prtvt7: Adjust default backlight brightness to 65
ARM: dts: imx6qdl: vicut1: The sgtl5000 uses i2s not ac97
ARM: dts: imx: Use 'eeprom' as node name
ARM: dts: imx6ul-ccimx6ulsom: Fix the "coin" regulator name
ARM: dts: imx: Use 'pmic' as node name
ARM: dts: imx6: Use the mux- prefix
ARM: dts: imx7d-sdb: Allow UHS modes
...
Link: https://lore.kernel.org/r/20230610072530.418847-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v6.5-rc1
This introduces support for the IGX Orin and Jetson Orin Nano devices
and enables various additional features on the Jetson AGX Orin and
Jetson Orin NX. This also enables some basic thermal support to prevent
the devices from overheating.
Support for the GPU on the Google Pixel C is enabled and various minor
issues are fixed and cleaned up.
* tag 'tegra-for-6.5-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable thermal support on Jetson Orin Nano
arm64: tegra: Enable thermal support on Jetson Orin NX
arm64: tegra: Enable thermal support on Jetson AGX Orin
arm64: tegra: Add Tegra234 thermal support
arm64: tegra: Add a few blank lines for better readability
arm64: tegra: Sort properties more logically
arm64: tegra: Enable GPU on Smaug
arm64: tegra: Add GPU power rail regulator on Smaug
arm64: tegra: Update USB phy-name for Jetson Orin NX
arm64: tegra: Enable USB device for Jetson AGX Orin
arm64: tegra: Add Tegra234 pin controllers
arm64: tegra: Support Jetson Orin Nano Developer Kit
arm64: tegra: Add missing cache properties on Tegra210
arm64: tegra: Fix PCIe regulator for Orin Jetson AGX
arm64: tegra: Add CPU OPP tables and interconnects property
arm64: tegra: Add support for IGX Orin
Link: https://lore.kernel.org/r/20230609193620.2275240-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v6.5-rc1
Several new modules and devices are documented and fixes incorporated
for the Tegra234 GPIO controller pin mappings as well as the possible
Tegra XUDC PHY connections.
* tag 'tegra-for-6.5-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra: Document Jetson Orin Nano Developer Kit
dt-bindings: tegra: Document Jetson Orin Nano
dt-bindings: gpio: Remove FSI domain ports on Tegra234
dt-bindings: usb: tegra-xudc: Remove extraneous PHYs
dt-bindings: tegra: Add ICC IDs for dummy memory clients
dt-bindings: tegra: Document compatible for IGX
Link: https://lore.kernel.org/r/20230609193620.2275240-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
This also removes a duplicate definition of the PWM fan and changes its
cooling levels. This should have no effect, though, because the fan
wasn't previously connected to anything and by default would be turned
off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add thermal zone details and enable the PWM fan as cooling device.
Note that this also changes the cooling levels for the PWM fan, which
should have no effect, though, because the fan wasn't previously
connected to anything and by default would be turned off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for the BPMP thermal node on Tegra234 and add
thermal zone definitions.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Surround device tree nodes with blank lines for increased readability.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We typically sort the "compatible" property first because it defines
what the remainder of the properties can be. For the sound node on the
Jetson AGX Orin this wasn't done, so fix that up.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
mipi_dsi node requires #address-cells and #size-cells.
Pass them to fix the following schema warnings:
imx8mq-mnt-reform2.dtb: mipi-dsi@30a00000: '#address-cells' is a required property
From schema: Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
imx8mq-mnt-reform2.dtb: mipi-dsi@30a00000: '#size-cells' is a required property
From schema: Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use 'dsi' as node name to avoid the following schema warning:
imx8mq-evk.dtb: mipi-dsi@30a00000: $nodename:0: 'mipi-dsi@30a00000' does not match '^dsi(@.*)?$'
From schema: Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On this board, vdd_bat is 16bit, not 24bit. Set the mode to
mode_voltage_16bit (3) instead of mode_voltage_24bit (1).
Fixes: 0d5b288c21 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They originated from the downstream kernel and slipped into mainline.
Remove them to silence also dtbs_check warnings:
pcie@33800000: Unevaluated properties are not allowed ('epdev_on-supply',
'hard-wired' were unexpected)
pcie@33c00000: Unevaluated properties are not allowed ('epdev_on-supply',
'hard-wired' were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the required bus-range property to PCI RC node. Fixes the warning:
pcie@33c00000: 'bus-range' is a required property
From schema: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add display APB and AXI clocks as required by bindings. This fixes the
warnings:
lcd-controller@30320000: clocks: [[2, 128]] is too short
From schema: Documentation/devicetree/bindings/display/fsl,lcdif.yaml
lcd-controller@30320000: clock-names: ['pix'] is too short
From schema: Documentation/devicetree/bindings/display/fsl,lcdif.yaml
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"fsl,imx8mq-lcdif" is compatible to "fsl,imx6sx-lcdif", adjust the list
accordingly. Fixes the dtbs_check warning:
imx8mq-tqma8mq-mba8mx.dtb: lcd-controller@30320000: compatible: 'oneOf'
conditional failed, one must be fixed:
['fsl,imx8mq-lcdif', 'fsl,imx28-lcdif'] is too long
'fsl,imx8mq-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif', 'fsl,imx8mp-lcdif', 'fsl,imx93-lcdif']
'fsl,imx6sx-lcdif' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The audio clocks should be intitialized to the correct rate by the subsystem
using them. There is no need to always initialize them from the CCM node
assigned-clocks property. This way boards using the audio clocks in a non-
standard way can change them without first duplicating the CCM clock
setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renesas DTS updates for v6.5 (take two)
- Add IOMMU support for PCIe devices on R-Car Gen3 and RZ/G2 SoCs,
- Add HSCIF1 serial port support on Renesas ULCB boards equipped with
the Shimafuji Kingfisher extension,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ulcb-kf: Add HSCIF1 node
arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
arm64: dts: renesas: Add IOMMU related properties into PCIe host nodes
Link: https://lore.kernel.org/r/cover.1686304614.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Clean-up for pinctrl-single node names for omaps for v6.5
To avoid producing lots of make dtbs checks warnings when the yaml binding
for pinctrl-single gets merged, let's fix up the pin group node names. We
want to do this rather than add non-standard node name workarounds to the
yaml binding.
Also included is a non-urgent fix to move gta04 model name out of the pinmux
node that can wait for the merge window.
* tag 'omap-for-v6.5/dt-pin-nodes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Unify pinctrl-single pin group nodes for dra7
ARM: dts: Unify pinctrl-single pin group nodes for am4
ARM: dts: Unify pinctrl-single pin group nodes for am33xx
ARM: dts: Unify pinctrl-single pin group nodes for ti81xx
ARM: dts: Unify pinctrl-single pin group nodes for omap5
ARM: dts: Unify pinctrl-single pin group nodes for omap4
ARM: dts: Unify pinctrl-single pin group nodes for omap2
ARM: dts: Unify pinctrl-single pin group nodes for omap3
ARM: dts: gta04: Move model property out of pinctrl node
Link: https://lore.kernel.org/r/pull-1685700720-242492@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use "dai-format" to configure DAI audio format as specified in
audio-graph-port.yaml bindings.
Fixes: 144d1ba705 ("ARM: dts: stm32: Adapt STM32MP157 DK boards to stm32 DT diversity")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The realtek Bluetooth module uses the same driver as the
realtek,rtl8822cs-bt and the realtek,rtl8723bs-bt, however by selecting
the 8723bs advanced power saving features are disabled that appear
to interfere with normal operation of the bluetooth module. This
change switches the compatible string to disable power saving. Without
this patch evtest of a paired bluetooth controller fails, with this
patch the controller operates as expected.
Fixes: b6986b7920 ("arm64: dts: rockchip: Update compatible for bluetooth")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230508160811.3568213-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it
and drop unnecessary ranges property.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The I2S0_8CH_MCLKOUT clock rate on Rock 5B board defaults to 12 MHz and
it is used to provide the master clock (MCLK) for the ES8316 audio
codec.
On sound card initialization, this limits the allowed sample rates
according to the MCLK/LRCK ratios supported by the codec, which results
in the following non-standard rates: 15625, 30000, 31250, 46875.
Hence, the very first access of the sound card fails:
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
However, all subsequent attempts will succeed, as the audio graph card
will request a correct clock frequency, based on the stream sample rate
and the multiplication factor.
Assign MCLK to 12.288 MHz, which allows the codec to advertise most of
the standard sample rates.
Fixes: 55529fe3f3 ("arm64: dts: rockchip: Add rk3588-rock-5b analog audio")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-4-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Indiedroid Nova is an SBC from a sub-brand of Ameridroid that
includes the following hardware:
- A 40-pin GPIO header
- 2 USB-A 3.0 ports
- 2 USB-A 2.0 ports
- A USB-C 2.0 OTG port (used for USB power delivery)
- A USB-C 3.0 port that can do display port output.
- A Micro HDMI 2.1 port.
- A 1GB ethernet port.
- An RT8821CS based WiFi/Bluetooth module.
- A user replaceable eMMC module.
- An SDMMC card slot.
- A MIPI DSI connector.
- A MIPI CSI connector.
- A 3.5mm TRRS audio jack with microphone input.
- An 2 pin socket for an RTC battery.
- A 4 pin socket for a debug port.
- A power button (connected to PMIC), a reset button (connected to SoC
reset), a boot button, and a recovery button (both connected to the
ADC).
- 4GB, 8GB, or 16GB of system RAM.
This initial devicetree includes support for the WiFi, bluetooth,
analog audio out/in, SDMMC, eMMC, RTC, UART debugging, and has
the regulator values from the schematics. ADC, graphics output, GPU,
USB, and wired ethernet are still pending additional upstream changes.
Analog audio will require changes to handle a difference between the
requested clock frequency of 12288000 and the actual clock freqency
of 12287999 before it will work properly. This will be done in a
subsequent patch series.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230531161220.280744-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
